Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

Thinking out loud about this 2008 Focus install

I saw a couple of other manufacturers have a T-Harness that works with the 2008 Focus, but not Fortin's.  I also noticed that the FORT1 is compatible with the 2008 Taurus.  So I pulled up the install sheets:

https://fortin.ca/download/107381/EVO-ONE_IG_REG_BI_FOR-FOCUS_2008-2009_A_107381.pdf
https://fortin.ca/download/95201/EVO-ALL_IG_RTS_BI_FOR-TAURUS-2008-2010_KEY40bits_A_95201.pdf

The ignition connectors appear to be the same form factor and the same pinouts, but different wire colors.  Just wondering if someone could perhaps review this and see if this would change the install options at all?  Like using the THAR-FOR1 with the EVO-ONE?  Or possibly being able to use the EVO-FORT1 or FORT4?

I do see that the Focus install has a Disarm wire connection that is not present on the others.  The other guide for reference is here

Appreciate it!

0

Remote start needs to be enabled on a 2008 Focus?

Looking into doing an install on a 2008 Focus. Came across this thread: https://fortin.ca/en/qa/103382/09-focus-remote-start-works-great!-However-the-heater-fan-does-not-run-untill-the-key-is-turned-on./ Wondering if one of the Fortin guys can verify if Forscan is needed or not. Haven't come across this before.

0

2008 volvo s60

Hi, I have 2008 volvo s60 std key automatic and i want to install evo all. Can you help me to find correct installation manual?

0

2008 audi A4 standard key 6 speed what kit is needed all in one if possible

can i know what is needed to install a kit to this audi

0

2008 Toyota Yaris without transponder

Hi guys. As you can see, I am trying to install an EVO ONE with KIT RFK411. I already have all the installation done but I have not been able to carry out the programming since this car does not have a TRANSPONDER. I am using this schematic: evo-one_ig_reg_bi_toy-yaris_2006_wokl_a_104141.pdf

Can you tell me what I should modify in the firmware, what programming should I do and what do I do with the TRANSPONDER connections? Thank you very much in advance.   https://ibb.co/phW8t2P https://ibb.co/tqhYCdM https://ibb.co/rfqFyW2 https://ibb.co/jM3xqSf https://ibb.co/MfkFq51 https://ibb.co/gzd5rTH https://ibb.co/3rGV5KZ https://ibb.co/k69KrmV

 

0

Why no remote start for 2008 A6

Just curious As to why remote start function is not a available for the 2008 Audi A6. I really do not want to rely on compustar or some other DEI product.

0

2008 chev express van dash lights stay on after remote start is shut off till door is opened. Evo-all

    Evo-all is hooked up wire to wire to a avital remote start, 4103

  i just timed it, when the remote start ends, the dome light comes on, the radio shuts off and the exit illumination activated, about 30 secs later the dome light shuts off, then about a min later the exterior lights shut off. However the dash lights remain on for another nine mins. They time out and turn off then.

0

20008 honda civic coupe manual transmission

good day. i want to install evo one on a 2008 honda civic manual transmission. i can see there is a diagram for automatic transmission but nothing for manual transmission. my question is do i just add the cluth bypass connection? is it the thin white wire(a5) or the thick white wire(e1)? thank you so much.

0

2008 Honda Odyssey

I have 2008 Honda Odyssey installed the Evo-one & Evo-Start2 with factory fob 3 times lock and App they are work perfect.

 i have one problem when use Evostart 2 app open sliding door only left sliding door work ,but right side doesn't work.

If i want both doors to work use the aux output (yellow/black) of the evo one connect to right side sliding door what colour wire of the car. i used guide # 86291 but didn't see it for sliding door wire, can you show me where it locate that wire and diagram?

Thank you very much.

 

SN:002B04189521

 

0

Red light stays on during programming and wont program the keys

I hVE 2008 Ford Escape. I installed the Evo all fort4 with the the t-harness. I have installed all connectors(1,2,3) and connected a relay to the lights as instructed in step 4. I plugged the black connector in while holding the button in and then let it go when the red light came on. I put in each key for 3 seconds each and then pushed the button in. It didn't start the vehicle. Red light stayed on teh whole time. It only blinked when I pushed the button in. What causes this and how can I fix it?

0

How to wire and programming

After programming my car won't turn over the car turns on but won't click over. When in on/run position led is yellow and not blue. I have a 2008 jeep Patriot I am not using any thing extra no kits no hood pin is there any thing else I need beside the Evo and harness for my vehicle

0

2008 Ford Expedition driver door pin wire location?

I am trying to locate the driver door pin wire on the driver's side.  I even cut a wire I was sure was it, only to find that the door chime still went off when I closed the door.  I obviously don't know how to test this correctly 

I tried disconnecting the two harnesses that are in the driver kick panel that are smaller, neither of them seemed to have any effect when disconnected them and closed the door, the chime still stopped.  So it must be in the large connector with the bolt through it, or somewhere else?

In the guide, its says "see diagram", but I can't find one in there to save my life.  I would prefer to stay on the Driver's side since I don't have any wire handy to fish over to the SJB.  Of course, at this point, I would take the SJB diagram, but can't find it.  Thanks for your help!

0

Q40 Parking lights turn on intermittently on remote start

I have the EVO-ALL with the T-harness installed on my Infiniti Q40 and G37S Coupe. The options are set identically. On the G37, when I remote start, my parking lights always turn on when I remote start the car. This is not always true on my Q40. More times than not, the parking lights do not come on at all. Option A14 is currently off on both vehicles. I tried turning this option on on the Q40 but there is no change on how (when) it works. The only real difference between the two is the type of RF kit I have installed. Any help will be greatly appreciated. Edit: Lights come on every time I remote start the car in the garage. Not when I start it outside the garage and it's sunny and bright. Lights switch is set to off for each of the tests.

0

JEEP patriot 2008 2.4 4*4 Fortin EVO-All +CHRT5 error p0513 in memory

Good day! JEEP Patriot 2008 2.4 connected Fortin EVO-ALL via CHRT5. Everything works as it should, the only moment that confuses and I want to solve this problem is that it gives error p0513 in the memory of the car. This happens when, after autostart, insert the key into the ignition switch, turn it to the "on" position and press the brake pedal. It turns out that when the control is transferred to the standard immobilizer in the key, the signal is lost and gives an error, but does not light the lamp. The key is programmed. After updating the firmware of the unit, I reset it to factory settings. It seems that I did everything according to the instructions. What could it be? Sorry for my english-gogl translation.

0

EVO-CHRT5 For Jeep Patriot 2008 I have factory fob, do I have to buy a separate remote starter or RFkit to make it work?

Hello all pro! Hi there, I bought EVO-CHRT5 (T-harness Included) for my Jeep Patriot 2008, my question is, do I have to buy a separate remote starter to be able to make it work? Im looking at the T-harness stand alone installation ( connection ) would this be the right connection for my Jeep? Yes my Jeep has a factory remote fob, but my problem looking at the stand alone wiring diagram is that one connector belong from T-harness ( black, 4 pin w/black and red blue white ) went to RF kit remote starter. do i have to buy this RF kit? can i just go along without making up this RF kit connection? And lastly the A2 and A3 from 20 pin EVO module which is the lock/unlock and the A13 start/stop, I bleieve this is an input which supposed to be connected from the vehicle lock/unlock door out put. but the A13 start/stop of 20 pin EVO ALL module where would this be connected from the vehicle? Also Im aware about the update and programming procedure I do have the the flash link updater im gonna be okay with that, Im just really confuse if i do have to buy a separate remote starter or RF kit to make my command start work. I hope someone can enlighten me Thank You so much !

0

Can i add motion and shock sensor at the same time to the evo-one?

I want to add a proximity sensor with the shock sensor

0

Honda Civic 2008 manual transmission I want to install an Evo one de do you recommend thanks

Tengo una transmisión manual Honda Civic 2008 Quiero instalar una Evo que guía de instalación me recomiendan gracias

0

2008 infiniti g37s coupe push start automatic transmission from us in miles

Hi guys I got the Fortin Evo-NIST1 with T-Harness and followed guide 80851 for auto transmission. I got all the wires mentioned connected. Brown wire from t harness to red wire by driver kick panel and the whiteblk to push start brown wire, at the bcm I got the two wires in the pin and tapped the 2nd wire which is red for me in the bcm. The bcm pin wire for (-) door pin is red color wire for me. The programming went smooth but The car doesn't start. When diagnosting I touch the dkblue wire to ground the break lights up and the module has red light. Three times lock the module blinks blue and that's all. Three times lock button module blinks blue everytime but the car does not start. The module does not have any lights after the blue blinks. Please help.

1

Blue LED goes out during bypass programming

2008 Hyundai Sonata Evo-One doesn't have PATS wire so I didn't use red connector and light blue wires from 20 pin connector. I finished all the wiring and checked it million times. When I press programming button and plug the 6 pin connector, let go on blue, connect 20 pin, antenna, valet, and can bus, put the key turn to on position LEDs go out. I tried turning on option 20.2 but when I plug the 6 pin connector all lights flash then they go out and nothing. I'm I missing something? EDIT: Turned out my antenna was faulty, everything works great now.

0

2008 Pontiac G5 Factory with Fortin

I have a 2008 Pontiac G5 it originally came with a factory remote start however it stopped working a year ago. I was wondering if I can install a fortin all in one? Thanks

0

How do I enable/configure trunk release using the linkr-lt2 with evo-one unit?

Can't configure trunk release on the linkr-2

0

08 Nissan Pathfinder - RF642W Lock Button Locks, Unlock Button Locks, Programming Settings or Wrong Wire?

2008 Nissan Pathfinder S - Standard Key - OEM Alarm Fortin EVO-ONE With NIS2 Harness Guide Followed: 75611 Unit was flashed to recommended/newest firmware prior to install. Service No: 002B07 200206 Everything is installed and working (As far as the Remote Starter Goes). When using the OEM Remotes the vehicle will lock and unlock as it always has. However, when using the RF642W remotes, The remote start works flawlessly (Push button, parking lights on, start/Crank, Run) The lock button locks the doors, but the unlock button also locks them (and does not unlock). The OEM Remote will unlock the door as normal with the remote starter running, but I would really like to not have to carry two remotes with me. Vehicle Running Oem Remote: Only Solid Yellow is on, No Blue Flashes RF642W: Lock - Solid Yellow, Blue Flash - Locks Doors RF642W: Unlock - Solid Yellow, Blue Flash - Locks Doors Did I miss a step? Enable/disable a wrong option? Any help is greatly appreciated. Thank You in advance.

0

08 Nissan Pathfinder - RF642W Lock Button Locks, Unlock Button Locks, Programming Settings or Wrong Wire?

2008 Nissan Pathfinder S - Standard Key - OEM Alarm Fortin EVO-ONE With NIS2 Harness Guide Followed: 75611 Unit was flashed to recommended/newest firmware prior to install. Service No: 002B07 200206 Everything is installed and working (As far as the Remote Starter Goes). When using the OEM Remotes the vehicle will lock and unlock as it always has. However, when using the RF642W remotes, The remote start works flawlessly (Push button, parking lights on, start/Crank, Run) The lock button locks the doors, but the unlock button also locks them (and does not unlock). The OEM Remote will unlock the door as normal with the remote starter running, but I would really like to not have to carry two remotes with me. Vehicle Running Oem Remote: Only Solid Yellow is on, No Blue Flashes RF642W: Lock - Solid Yellow, Blue Flash - Locks Doors RF642W: Unlock - Solid Yellow, Blue Flash - Locks Doors Did I miss a step? Enable/disable a wrong option? Any help is greatly appreciated. Thank You in advance.

0

can i connect Brwn/White (Parking Light) wire from EvoAll to my Parking light relay.

Can I connect the Br/White wire from EvoAll to my Parking Light relay instaed of the Pink/Red of my Dakota?

0

2008 Ford Mustang. Can I use obd pins 6 and 14 for CAN bus instead of 3 and 11?

Just wondering if I can use OBD2 pins 6 and 14 for CAN bus comms with my EVO-All on my 2008 Ford Mustang. Not sure pins 3 and 11 as stated in guide are communicating properly. No door lock/unlock etc.

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue