Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

07/11/2021

 Ford Jesse Slone (130Pts.)

0

2008 Ford Expedition driver door pin wire location?

I am trying to locate the driver door pin wire on the driver's side.  I even cut a wire I was sure was it, only to find that the door chime still went off when I closed the door.  I obviously don't know how to test this correctly 

I tried disconnecting the two harnesses that are in the driver kick panel that are smaller, neither of them seemed to have any effect when disconnected them and closed the door, the chime still stopped.  So it must be in the large connector with the bolt through it, or somewhere else?

In the guide, its says "see diagram", but I can't find one in there to save my life.  I would prefer to stay on the Driver's side since I don't have any wire handy to fish over to the SJB.  Of course, at this point, I would take the SJB diagram, but can't find it.  Thanks for your help!

Login to reply View 1 answer(s)

29/03/2019

 Ford Nelson Santos (130Pts.)

0

Will the firmware for 2016 expedition standard key work for push to start?

Firmware compatible.
Login to reply View 1 answer(s)

21/03/2019

 Ford Geoffry LALAND (160Pts.)

0

What will work for a 2014 expedition

2014 expedition
Login to reply View 1 answer(s)

20/03/2019

 Ford Geoffry LALAND (160Pts.)

0

What is a standard key mean on a 2014 Expedition

What is a standard key
Login to reply View 1 answer(s)

14/03/2018

 Ford Chris Vaughan (130Pts.)

0

EVO One; after remote start vehicle will not shut down

I've installed two of these, within a month of each other. Both installs went smoothly. However, this last one is a 2007 Expedition. I can start it with the fob w/3x Lock, and kill it with the 3x Lock. But it is letting me drive the vehicle without the key and will not shut off with by pushing the brake, or with the key. After the full run time, it stops like normal. I have not tried driving it for 15 minutes, as i'm afraid it will shut down while driving. A1-A11 are active.
Login to reply View 2 answer(s)

13/10/2015

 Ford Orlan (210Pts.)

0

2014 Expedition lock, unlock, driver pin wire color / location.

Hello, I have a Pro-Start remote starter that will be connected to EVO-all using d2d. I will be using guide 3318, connection 4 as per guide. My question is where do i connect the lock , unlock and driver pin wires of EVO-all to the vehicle? The guide shows to connect the wires from evoall to pins 6,8,9 of the connector in the vehicle for lock/unlock/driver pin. However, slots 8 and 9 are empty and slot 6 is for factory alarm arm. As per Autostart wiring guide, lock is at pin 17, unlock at pin4 and driver pin at pin 14. Can you please clarify where to connect the lock/unlock/driver pin wires from evo-all to the vehicle? Also, the guide shows to connect the remote start ignition and evo-all keysense wires to the number 1 pin of the PATS module. The guide labeled it as Keysense. The vehicle wiring guide shows it is Pats Ignition and that the keysense wire of the vehicle is at the ignition harness (blue/gray). Do I go ahead and connect ignition and keysense wire as per evo-all guide? or should i connect to the wire specified in the vehicle wiring guide? Also, if the vehicle does not have factory alarm, do I still connect notes 1,2,3 (in green). How would i wire connector D (red 6 pin harness of evo-all) if there is no factory alarm? Last question, how do i know if the vehicle has 40-bit or 80-bit keys. Evo-all guide only lists 2014 expedition as 80 bit however, other bypass modules (idatalink) lists this vehicle as 40 bit key. Can you please advise? Thank you in advance.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue