Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

Will the evo-vwt3 work on my VW Passat 2018 standard key and where can I find install instructions

0

2017 Forester can't program DCryptor

2017 Forester X, key start, new EVO-One, installed per Guide #97491w/THAR-ONE-SUB1 t-harness, all connections made per pin location, not wire color. When I reach Step 5 on the DCryptor programming and start the car, I get red/blue on solid and they stay on even after the car is shut off, until I pull the 6-pin. Car starts normally with the key if the EVO-One is connected, will not start with the red plug disconnected, which I believe is correct. I've reset and reprogrammed the module twice with the same result.

Update after reading multiple other recommendations about getting to solid red and blue at step 5: 1. Instructions say to use Firmware 84.11 (minimum), I have 84.12 and .11 is not available. 2. I checked continuity  from pin 10 (light blue) of the 20 pin connector (IMO signal) to pin D1 (Yellow/green) IMO body side and have continuity. Car starts and immediately quits with red "D" connector unplugged,  starts and runs normally with it plugged in. 3.  Have battery voltage at E1 (white) and E5 (pink) with ignition on, no power with ignition off. Module SN:002B04 656833.

0

What’s needed? 2017 Audi S3 PP DSG Virtual cockpit

As title states what do I need to order to install remote start capabilities. Which system EvoRS, Evo One, T-harness AUD1 or 2, bypass modules, etc. Thanks in advance!

0

2015 Fiat 500 Standard Transmission install diagram

Is there install diagram for 2015 Fiat 500 standard Transmission installing EVO-ONE-3641 and EVOStart LTE Thank you in advance Michael Pepper Mobile Sound Systems

0

Install guide

02 gs300 I am looking for a simple install guide for the evo one without the t harness.

0

2015 Kia Sorento Standard Key T-Harness Evo-One Step 4 Solid Amber Light

Installing a Evo-One in a 2015 Kia Sorento with T-Harness and standard key. Completed wiring. Spliced yellow A1 into pink ignition wire in T-Harness. Cut white wire in T-Harness. I have flashed the Evo-One with the lastest firmware in both remote start connection and bypass mode. In FlashLink Manager for desktop Pro Mode, I set the mode to OEM Lock-Unlock-Lock on 38.4(?). I am using an OEM key. That is the only option I configured. With the key out, I plug in the 6 wire harness while holding the programming button. Lights flash red->blue->red & blue->yellow and I release the button. Yellow is solid on, other lights are off. I plug in the remaining connectors. Insert the key into ignition, and turn to RUN position. The light stays solid yellow. I have probed the C2 & C4 and have 2.4v for CAN-Low at the C connector. I have 2.6v at the C1 & C3 connector for CAN-High. I can not get to the blue flashing x10 times in the programming steps. Car starts normally with key.

0

2018 RVR LED & headights light Flash continusuly after Remote Started

Hello everyone We installed an Evo-One on this RVR 2018 with factory HID headlights and LED Fog light using 23101 guide. We followed the guide to a T, the issue we are have is that as you remote start the vehicle using 3X lock the vehicle starts properly, but if the lights are set on automatic, the headlights and LED lights flash continuously as well if you turn off the lights and remote started the Vehicle the LED fog lights flash continuously both will flash until you take over the vehicle. Has anybody come across this? We think it might be a faulty EVO one module any thoughts please help.

0

Fortin Evo-ALL will not program

2018 VW Tiguan Standard Key, Automatic Trans, no Heated steering wheel I have the THAR-VW6 installed correctly. The EVO-ALL will not program. When trying to program, I hold down the programming button and connect the data link cable, light goes to blue, I release, all 3 light flash. I have an R-link and a Flashlink. I've flashed the EVO-ALL with the correct firmware. Service# 001A07 367521 Please help.

0

OVE-ONE no LED lights when 6 pin main harness is inserted

EVO-ONE with HON2 Tharness and EVO Start module. Programming with Flash Link Updater was completed successfully but when connecting 6 pin main power harness inside the vehicle while holding down the programming button, none of the LED lights illuminate. Power harness leads were tested with a multimeter and there is 12 volts but the EVO-ONE LED's do not light up so I cannot enter the dcryptor programming mode. Even though none of the lights on the EVO-One illuminate, the connected EVO Start module has a flashing RED led so there is definitely power going to the EVO-ONE. Installed on a 2019 Honda Civic

0

2015 Forester (push to start) , shut down immidiately after remote started.

2015 Forester (push to start) , shut down immidiately after remote started (after 1 or 2 second), what im missing here?

0

EVO-One with THAR-TOY16 Programming stuck at step 7

Hi Fortin support team: Vehicle: Lexus RX350h 2024 (Hybrid vehicle) EVO-One GUIDE: #116181 Rev:20240513 Firmware: both 88.33 & 88.34 EVO-One S/N: 002B04659051 Programming stuck at step 7: The BLUE LED will not turn OFF, The RED LED will not turn ON. Unable to add RFK942. What should I do?

0

2012 Hyundai Sonata PTS - No ignition control - EVO All

2012 Hyundai PTS Fortin EVO All with Fortin LTE Connected all wires as per installation instructions. Bought Flash link and flashed to 17.31 following the wizard. Programmed Frotin Evo module to vehicle(blue LED blinks rapidly). When pressing starting lock 3x - module sounds internal relay is clicking and parking light flash however dash ignition does not come on. Checking EVO all diagram - RED Connected D2 yellow/blue start+ wires goes into 1n4004 diodes - strip facing towards PTS button - then to yellow/black and yellow/orange. ignition does not turn on. Disconnected the diodes to measure direct and yellow/blue wire for voltage output...getting zero volts when remote start is requested. Tried to reflash Fortin 4 times and still have not been able to get voltage output from d2 yellow/blue. I am missing something or is there internal module fault?

0

2012 Hyundai Sonata PTS - No ignition control - EVO All

2012 Hyundai PTS Fortin EVO All with Fortin LTE Connected all wires as per installation instructions. Bought Flash link and flashed to 17.31 following the wizard. Programmed Frotin Evo module to vehicle(blue LED blinks rapidly). When pressing starting lock 3x - module sounds internal relay is clicking and parking light flash however dash ignition does not come on. Checking EVO all diagram - RED Connected D2 yellow/blue start+ wires goes into 1n4004 diodes - strip facing towards PTS button - then to yellow/black and yellow/orange. ignition does not turn on. Disconnected the diodes to measure direct and yellow/blue wire for voltage output...getting zero volts when remote start is requested. Tried to reflash Fortin 4 times and still have not been able to get voltage output from d2 yellow/blue. I am missing something or is there internal module fault?