Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

OVE-ONE no LED lights when 6 pin main harness is inserted

EVO-ONE with HON2 Tharness and EVO Start module. Programming with Flash Link Updater was completed successfully but when connecting 6 pin main power harness inside the vehicle while holding down the programming button, none of the LED lights illuminate. Power harness leads were tested with a multimeter and there is 12 volts but the EVO-ONE LED's do not light up so I cannot enter the dcryptor programming mode. Even though none of the lights on the EVO-One illuminate, the connected EVO Start module has a flashing RED led so there is definitely power going to the EVO-ONE. Installed on a 2019 Honda Civic

0

How to Wire Clutch Pedal Stroke Sensor for 2020 Honda Civic Type R

Hello I have the Evo-One and Fortin THARONE-HON7 T-Harness. Everything is wired up but I'm not sure how to create a relay to connect to the clutch pedal stroke sensor.

0

HONDA CR-V 2018

Hi dudes. HONDA CR-V 2018 wire colors doesn't match. Can I use this colors order instead? Cuz in the scheme only the ignition connector match. Please and thanks you.   https://ibb.co/rsk37g3 https://ibb.co/JkSF2Wv https://ibb.co/vJnQbNR https://ibb.co/5KqkYB5  

0

An error occurred while detecting your module, please replug and try again or contact customer support.

When connecting my EVO-One to the Flash Link I'm receiving an error message: An error occurred while detecting your module. Please replug the module and try again, if the problem persists contact customer support. The red light on the device near the yellow loop wire is solid red when plugged into the computer or vehicle. I'm presuming the device needs to be reset by support or replaced. S/N: 002B04 162218

0

Why can't I program my EVO-ONE on my 2015 CR-V?

I am trying to install an EVO-ONE remote starter on my 2015 Honda CRV Push-to-Start. I am using the T-harness. I connect the 24 and 28 pin connectors correctly. When I hold down the program button and plug in the 6-pin plug, nothing happens. No lights turn on on the module. I know I am doing this part correctly. Previously, I had an EVO-ALL and got it set up correctly (but I ditched that effort because I couldn't get the Crimestopper remote starter to work and just bought the EVO-ONE). I did this process on the EVO-ALL (using the 4-pin data link wire) countless times without difficulty - this part was never the problem. Why don't I get any lights at all when I hold down the program button and plug in the 6-pin connector on the EVO-ONE? I have updated both the "bypass" side to 73.31 and the "remote starter" side to 1.24 using the Flashlink. I updated the bypass side, then I unplugged it from the computer. Then I plugged it back in and updated the remote starter side. On the bypass side, I have C1, D2, and D6 enabled. On the remote starter side, I have 38.2 enabled. None of that even matters because the module won't even light up when I plug it in! Of note, if I have the 6-pin main harness plugged into the EVO-ONE and turn the car's power on, it does flash some lights - so I know it is getting power.

 

This is my only concern: I am using the T-harness that came with the EVO-ALL + Crimestopper kit that I purchased online prior to giving up on that and switching to the EVO-ONE. The label on the T-harness says "THAR-HON3". It does not say "THAR-ONE-HON3". However, it appears to be the exact same harness as the THAR-ONE-HON3. It has all of the same connectors. Please do not recommend to me that all I need to do is buy the T-harness that is specifically called "THAR-ONE-HON3" unless you are absolutely certain that this is the issue because I have already spent more money than I should have trying to install a stupid remote starter on my vehicle. I only see one type of T-harness available on this website for my push-to-start vehicle, so I don't think that there is really a difference between the two. However, if you know for a fact that there is a true difference between "THAR-HON3" and "THAR-ONE-HON3" and that the "THAR-HON3" T-harness is incompatible with the EVO-ONE, I will buy the THAR-ONE-HON3 T-harness.

 

Sorry for the long post. I am just trying to anticipate any follow up questions and go ahead and address them. Thanks in advance for your help. I'm almost ready to throw all of this in the trash and buy a car with remote start on it.

0

Honda CR-V 2014 Evo one

i have honda crv 2014 standard key , and i am installing evo one with T-harnes 2 and RF2W antina fob , i connect same what is show , i and i follow the instruction solied red then push twich flash red , then pust the key to ignition fast red falshing but the blue light will not show after 10 flashing and even at all all the wires are connected by the T harnes and the orand wire and the pink wire are connected for each connecter 12 pin and the 20 ping , the ground is connected , the only wire is not connected is the fuesed wire which is pin 1 white or brown in the T harness which is said it is output , i never touch the programming yet for the interface of the unit which is still the default setting from the manfacure , any advice or suggestion . ?

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue