Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

31/01/2024

 Audi Vitalii Vasylchuk (240Pts.)

0

Audi a6c7 problems rmf411

I need help realy!!! I installed it evo-one + rm411, starting with the OEM key works.3 item close is car in run. I wanted to install rm411, the programming of the key fob is successful, but it does not react to it.no open, no close, no run engine... how should it be???maybe you need settings??? I have 2 of them, here is one of them, the other is in the car, bought this year. on this block 002B04 650369 need to reset the decryptor because I didn't understand what was wrong and tried many others...please help me to do it right...and to work rmf411, really needed maybe somewhere in the settings you need to put a point that there is an additional remote control and not OEM
Login to reply View 1 answer(s)

13/01/2024

 Audi Dsk (140Pts.)

1

EVO ALL - 2012 Audi A4 Step 7 flashes red 3 times

I am in the process of installing this and I get to step 7 and it is supposed to be solid red then in step 8 red and yellow alternating. At step 7 after Blue red yellow alternate it goes to 3 red flashes over and over. What could be causing this?
Login to reply View 0 answer(s)

02/01/2024

 Audi Drake Trebon (180Pts.)

0

2014 audi a6 push to start unable to complete decryption process EVO-ONE

Im able to get the module into programing mode with the flashing red, yellow, and blue lights. The vehicle will shut down (key off) durring the process but will not key on. The key off happens near the end of the programing procedure i belive this is supposed to be a signal to key on and complete the key learning. I also notice the evo one will light blue when the fob is pressed but when remote start sequience is started no lights illuminate on the module. Im thinking firmware issue im running 60.10 as recomended and tried a few others. module # 002B04 266571
Login to reply View 2 answer(s)

02/01/2024

 Audi Drake Trebon (180Pts.)

0

2014 audi a6 push to start unable to complete decryption process EVO-ONE

Im able to get the module into programing mode with the flashing red, yellow, and blue lights. The vehicle will shut down (key off) durring the process but will not key on. The key off happens near the end of the programing procedure i belive this is supposed to be a signal to key on and complete the key learning. I also notice the evo one will light blue when the fob is pressed but when remote start sequience is started no lights illuminate on the module. Im thinking firmware issue im running 60.10 as recomended and tried a few others. module # 002B04 266571
Login to reply View 2 answer(s)

23/01/2023

 Audi Jose ortiz2 (130Pts.)

0

2008 audi A4 standard key 6 speed what kit is needed all in one if possible

can i know what is needed to install a kit to this audi
Login to reply View 1 answer(s)

20/12/2022

 Audi Vincc (230Pts.)

0

Can't complete Step 5 - Blue LED don't Flash. Audi S4 2014

Anyone can help me? I'm Stuck on Step 5 while programming my EVO-ALL with the T-Harness EVO-AUDT1 on My Audi S4 B8 (2014). The BLUE LED doesn't begin flashing. CAN Connections are Good. I Measure round about 3V on the Whit 5 Pin connector between Grey and Grey-Black. Grey-Black goes to Orange-Brown (CAN-Low) and Grey goes to Orange-Green (CAN-High) like in the Guide described. I have connected these Cables at the CAN Connector near the Relays at the left bottom under the Driver footwell. S/N: 001A06905491 Thanks!
Login to reply View 1 answer(s)

06/01/2021

 Audi jeremy vermeulen (670Pts.)

0

looking for a no key required for Audi A4 and Q7 2017-2020 solution using thar-aud2

i am looking for a bypass soloution for 2017-2020 Audi A4 and Q7 models that do not require a sacrifice key. also want to be able to use t harness to avoid splicing the wiring in the vehicle. the customer only has one operational key for the vheicle.
Login to reply View 1 answer(s)

11/11/2020

 Audi Jake Thomas (200Pts.)

0

DCryptor procedure / Acquire data - Evo-One module

Hi,

I forgot to Acquire data from the car and the module Evo-One was already updated, so during the installation page 6/10 step 4 the BLUE LED switchs off when i turn the ignition ON  https://cdn02.fortin.ca/download/77141/evo-one_ig_thr_bi_aud1-a4-a5-q5-s4-s5_2015_pts_a_77141.pdf 

So i am wondering if i should to do factory reset the module AND HOW to do it! According this answer https://fortin.ca/en/qa/67178/evo-one-reset the module must be installed on the vehicle which is not in my case.

I could'nt find those following connecters:

12. immobilizer data purple/blue

17.  start/stop black/blue

18. start/stop 2 black/red

19. start/stop 3 grey/blue

25. key release Grey/yellow

and more.

Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue