Good afternoon,

I am having an issue with my 2016 Mustang MT not cranking or starting with the remote start feature. Vehicle goes into ready mode after the correct sequence, the module clicks and a solid red LED appears on the back of the module itself. After setting ready mode, I hop out and press lock twice to kill the vehicle. Lastly, I use the 3x lock sequence to remote start the vehicle, it primes, and I just hear the relay that I installed clicking over and over and the accessory mode turning on and off repeatedly until I manually start the vehicle to break the sequence. I thought it was an issue with the sacrificed key, but I held my regular-use key fob in the vehicle to confirm that it wasn't the issue, still the same condition as before. All connections look to be good, only soldered connections were used.

SN: 002B04 710520

Thank you for your help.

I finished installing the EVO One on my 2014 Subaru Forester 2.5i. I connected all the required cable according to the guide. I used Flashlink to install the 84.12 Bypass firmware and 1.26 Remote starter firmware. I successfully completed the programing procedure in GUIDE # 97491 for Evo one with THAR-ONE-SUB1 harness using decryptor. I also enabled the 3x oem remote start setting. The issue I am having now is the would sometimes start momentarily then immediately dies or the starter would click but not turn over. I tried messing around with the tactless sensitivity levels in flashlink but still having the same issue.

I recently purchased the THAR-ONE-MAZ5 with the EVO-ONE remote starter and immobilizer bypass module for my 2023 Mazda CX-30. I installed everything following Manual #99841, but I’m experiencing an issue.

Problem 1: Vehicle Shuts Down After Takeover  

After remote-starting the vehicle using my OEM key, I follow the takeover procedure (Page 11 of Manual #99841). However, as soon as I press the brake pedal, the engine shuts off.  

Problem 2: A/C & Accessories Not Working Properly

Additionally, most accessories (including A/C) do not turn on during remote start. Even if I manually activate the A/C after remote starting, I can hear the compressor running, but the blower fan does not work nor the A/C interface screen.

Neither THAR-AUD1 nor THAR-AUD2 lists the 2017 TDI Key port as compatible;  however the EVO-ONE lists Q5 2017 as compatible.  I have a 2017 Audi Q5 B8.5 2.0 TDI Ultra , automatic transmission with CNHA engine code (sold Outside US)  and I would like to buy a EVO-ONE with the correct harness for my vehicle. 

Do I have to buy a THAR-AUD1 or THAR-AUD2 harness separate to the EVO-ONE for 2017 Audi Q5 B8.5 2.0 TDI Ultra, automatic transmission with CNHA engine code ? If so,  Which do i Buy,  THAR-AUD1 or THAR-AUD2 for 2017 Audi Q5 B8.5 2.0 TDI Ultra, automatic transmission with CNHA engine code?Will I have to sacrifice a key? 

Hello everyone, 

Looking to install this evo all with this radiostar generation remote starter (https://policeauctionscanada.com/Listing/Details/49897032/Radiostar-2-Way-LCD-Vehicle-Security-System-Remote-Start-240093B) As my buddy is insisting to use it. It wouldve been a lot easier if i do it with fortin RF kits. Anyway. My question is according to the this diagram on the fortin website (https://cdn02.fortin.ca/download/66011/EVO-ALL_IG_SAL_BI_FOR-EDGE_2015-2017_C_66011.pdf)

Where should i connect all those dotted lines going to the remote starter? There is no datalink on this remote starter. Unlock and lock to the remote starter side? Specifically the “start/stop external” and the “convenient ignition out” from evo all going to the remote starter side? Im confused. Please help. I appreciate it. Thanks in advance

Hi i have evo one and i change in settings on my flashlink 4 the number 6 option it says door lock before and after remote-start it was no so I chose Look after remote-start 8.3 after that when i run my car by the remote my wheels don't turn full only half but when i turn my car by the button it's work fine so I do the reset bypass side and return to the flashlink 4 and the same option number 6 door lock before and after remote-start and I put it back to no like it was and i did decryptor but nothing change the opinion didn't work when i turn the car by remote didn't happend like before it was like door open the closing then the car run 

My evo one SN#002B04108420

Flashlink 4 SN#002505 085445

Bought a used car with “Orbit One remote starter & alarm & bypass module”

Starter Vr: 7.1.21 , Evo-All Vr: 4.18

Serice No: 002B07 323505

Was bought without a remote start key, wondering if I am able to program a new key, or remove the entire system and have done by dealer