Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

25/12/2023

 Volkswagen oleg07 (130Pts.)

0

2012 VW Jetta would not start from any of the remotes and OEM remote after successful programming

I just installed the EVO-ALL with the VWT3 harness, programming went good but the vehicle doesn't start from any of the remotes, the module lights up ( red then yellow and both stay on ) and never get ignition or accessory turned on. The wiring is connected properly, I double-checked everything and tried different coding but still no result and it does not recognize the OEM remote 3 lock clicks or Lock-Unlock-Lock. I am out of ideas, only thing that comes to my mind is that my ignition switch has a different pinout, also after loading the recommended coding it started to give me a 4 RED LED blinks. I am out of ideas, any help would be greatly appreciated. SN: 001A07 367259
Login to reply View 0 answer(s)

23/07/2023

 RF-Kits holdmybeer (150Pts.)

1

RF642W - Two way communication not working

In order to have a remote with each physical key, I purchased a 2nd RF642W kit. After pairing the remotes from the 2nd kit to the vehicle the remotes work in that they are able to preform all the functions. However, they don't appear to recieve 2 way confirmation. The most annoying part of this is when I press lock/unlock on one of the 2nd kit's remotes the vehicle locks/unlocks 3x before the remote says it did not work (even though it did). Is there a way to get the remotes from the 2nd kit to recieve the 2 way confirmations?
Login to reply View 1 answer(s)

15/12/2022

 Hyundai Brian Sahid (420Pts.)

0

Signals, headlamps, etc not working after remote start.

2019 Elantra GT manual with EVO ALL, Compustar CMX. Vehicle starts properly, but after a remote start sequence the signal, headlamps and a few other accessories related to steering wheel mounted controls do not work. Only way to regain operation of these functions in to remove cars battery for a few minutes. Happens only after 5-8 remote start sequences. Removed parking light control from EVO and hard wired directly to Compustar with appropriate resistor with no change.
Login to reply View 1 answer(s)

20/03/2022

 Subaru PJ Jan (340Pts.)

0

key Bypass

My Dcryptor has reached its limit 

model S/N 002B04171986
Login to reply View 1 answer(s)

06/03/2022

 Volkswagen anatoliy guzovatyy (130Pts.)

0

Remote 642w not working after successful pairing,but works from OEM remote

Installed new remote 642w and successfully paired with evo one module, but not working at all . Option for this remote H2 is on . Evo one works fine from OEM remote. What others hidden problems can be? It's for 2013 vw Passat. Thank you for replying!
Login to reply View 1 answer(s)

17/01/2022

 BMW Mark B (130Pts.)

0

Programming or wiring?

A random shop installed this mobile start 3 years ago and ive had issues on and off with mobile connectivity for the past year(of course shop disappeared). 06 BMW 330xi manual transmission, with push start Just installed a new receiver to update the old one that is no longer supported. Mycar brand of mobile starter. Prior to installing the new receiver the car would function normally minus the mobile start would not connect. Changed the receiver out to the new 4g module and now car is connected to the app and all the functions work except for remote start. Car needs to be put into "ready mode". Go to manually start the car and it will not crank. If the program button on the evo-one controller was bumped, will that disable any of the starting functions? If this module needs to be programmed, could it block the clutch sensor and stop the car from starting? I didnt see any wires fall off and the "depress clutch" symbol popped up once on the dash. Looking for a spot to start diagnosising the no start issue.
Login to reply View 1 answer(s)

19/12/2021

 Chevrolet Jacob Landis (130Pts.)

0

Remote Start not working after programming

Just finished installing the remote starter kit on my 2019 Silverado 1500 LD. Followed all the instructions and everything went exactly as desicribed in the manual. After programming and reinstalling the RS Module, the truck will not remote start. No LEDs lighting up when I push the lock button 3x as instructed.
Login to reply View 1 answer(s)

28/10/2021

 Toyota phap truong (250Pts.)

0

2007 highlander hybrid key bypass programming

I've followed the programming instructions and press and hold the programing button, plugged in the wiring and then let go of the programming button when it gets to RED, but it's stuck on RED and never starts blinking 10 times to start the programming. I've tried this both on my EVO ALL and EVO ONE with the same results. I've double check all my connections and metered between them to make sure the connection is good.
Login to reply View 1 answer(s)

20/10/2021

 Nissan baldev jhutty (190Pts.)

0

bypass key programing

i have a 2012 nissan versa without intelegent key im using t harness. i plugged in all plugs and connected flash link updated module. now i was KEY BYPASS PROGRAMMING PROCEDURE . i did firs 2 steps now when i go to turn on key the yellow led is solid and red does not turn on. please help also i have not connected any lock unlock wires and driver door pin or the hood pin aswell as the parking light wire.
Login to reply View 2 answer(s)

28/09/2021

 Toyota Jeffrey Garoon (170Pts.)

0

Dot key + bypass not working

06 highlander dot key + Evo one 442. Not registering key signal upon insertion. I've been told this vehicle requires bypass, but am unsure how to program the remotes.
Login to reply View 1 answer(s)

12/08/2021

 Buick Mohamed Ali (450Pts.)

0

RF912 KIT SOUND

Normally when i press the rf kit remote it makes a sound that car recieved the order, but recently my remote is giving 2 more short beeps after the first one, though it might be low battery indicator but changed the battery and it remained the same, any ideas ?
Login to reply View 1 answer(s)

18/04/2021

 Toyota dominic marcil (250Pts.)

0

Rav4 XSE. 2021

Rav 4. 2021. XSE. Hybride push avec un évo one et toy13. Tout fonctionne bien sauf que le. Remote Connect original avec application ne veut plus démarrer
Login to reply View 1 answer(s)

26/03/2021

 Hyundai Kevin Raymond (250Pts.)

0

Evo One won't start after 5 min or so but was working right after key bypass programming procedure

Hi, I'm kind of lost here, nobody seem to have the answer to my problem, not even Fortin when I call them for help. I installed my Evo One on my Hyundai Tucson 2020 standart key start, followed exactly all the wiring as per the guide, double check all my connection (EMS, CAN BUS, ignition wires, etc) and there's no loose cable. After that I did the key bypass programming procedure with EMS cable : hold down program button while plugging the 6 pin heavy gauge wire till it was red, plug all the others wires, press 7 times program button till it flash 6 times every second, put the key in and turn to ON. At this point the red led flashed 10 time quickly and after stayed on while the blue light started flashing quickly too. After that I turned Ignition to OFF and every light turn off. Right after that I tried to start the car by pressing LOCK, UNLOCK, LOCK and the car started no problem. I then stop the car, close the door and wait... 5 min later, I tried to restart the car with the remote starter but it didn't work. The car got the lock unlock lock signal but no light is flashing on the module anymore like if it went into sleep mode or something. I tried many thing and here is what I found out : - If I unplug all cable from the Evo One and plug it straight back it then start receiving signal again for the next 5 min or so. - If I open the trunk and close it back, the module seem to start back receiving signal from oem remote. To me it feel like there is a cut off or something that stop the module from receiving any signal from the oem remote after a certain amount of time, kind if it was to prevent from draining the battery of the car. Could also be that the Evo One is loosing the key programming after current shutting off in the car but then it shouldn't start by just unplugging and replugging the 6 pin ignition wires. *Sorry if my english is not perfect, I usually speak french.
Login to reply View 2 answer(s)

06/12/2020

 Toyota jonathan finch (200Pts.)

0

2010 RAV4 dot Key fail to program

I have EVO-ONE-Toy and a T harness. I get thru the key recognition (10 red flash) but no blue lights. I have checked my CAN high and CAN low multiple times. Any Suggestions ? Also have tried with 79.48 and 79.64. Trying to keep this simple with 3x lock to start.
Login to reply View 1 answer(s)

08/11/2018

 Chevrolet John Steel (160Pts.)

0

Only blue light flashing

Hello. I am able to update firmware and program EVO-ALL to my truck with no problems. Decrypting also works but when I then plug it into my truck it just slowly flashes the blue led.
Login to reply View 1 answer(s)

05/07/2016

 FAQ derek g (325870Pts.)

3

What is the correct way to connect wires?

T-Taps, Butt connectors 2 pounds of solder I've seen and heard it all...most of the time resulting in a headache and lost time. So i thought i would break it down and show the 5 easy steps to make a good quality and secure connection in a vehicle.

The 5 Steps are as follows:

1- Strip back the inulation of the wire you wish to connect to.

2- Seperate the braid to create an opening in the wire.

3- Insert the wire that is to be connected into the opening.

4- Close the wire.

5- Finally twist the wire around securing them togehter and finish it off with some electrical tape.

Login to reply View 0 answer(s)

09/02/2018

 Ford Remi Mercier (160Pts.)

0

Nothing happen after programming

Hi, I bought a Evo All with FORT-1 Harness for my 2016 Transit. All wires plugged and checked twice(except for light wire cause I dont want them to light up). When I do the programming sequence, all the light flashes has they need. but when I at the point of remote starting within the 5 seconds, it does not.. and then the blue light flash 10 times then the dash turns off and no sign of the Evo.. when I press my remote, I have no lights going on the EVO at all. Also, during programming, the dash says No Key detected. For info, I already installed a Evo in my 2015 F-150 and worked great..
Login to reply View 1 answer(s)

16/05/2017

 Mazda Nick Ter-Kuile (280Pts.)

0

Cant upload data to Dcrytor or Flash Unit

2017 Mazda CX9 Push To Start Unit Wired up as per guide 65561 Using Evo-ALL & THAR-MAZ2 Unit responds via LED's all as per instructions When sending Data to Dcryptor it appears to show no progress even after 1 hour Have updated Remote Start to V1.21 however after update flashlin kmanager freezes at EVO UPDATE SUCCESSFULL. Flashlink Manager red and & green are solid. Blue is blinking. No lights on EVO-ONE. If i disconnect and reconnect it goes to Bypass mode. Running V71.43, if i click Flash it tries to flash unit and then says unit discconnected - EVO RED led is flashing, Flashlink Red LED is Solid. I have to discconect and reconnect to get it to appear in flashlink manager again
Login to reply View 2 answer(s)

08/03/2017

 Dodge mohammed salladin (710Pts.)

0

Chick engine flashing

Hi sir am working on Dodge Charger 2015 it's complete working and car starting engine normally but we found chick engine flashed ,we read it by diagnostic tool and found U0415 invalid data received from Anti-lock break system control module we erase it and start by PTS no errors come once we start engine by 3lock errors come this problem comes in jeep and dodge 2014 and more , any help
Login to reply View 1 answer(s)

09/04/2017

 Jeep Gino Rocha (160Pts.)

0

Blue Light Flashing After Programming

I have a Jerp Commander 2007, followed instructions. Added yellow cable, everything went smooth with programming, till the point where u take key out and hit lock button. After that blue led light just flashes and won't start the vehicle. Any ideas?
Login to reply View 1 answer(s)

02/01/2017

 Ford Chad Cyr (950Pts.)

0

EVO-ALL - "Died" after flashing/programming - No LEDs/No Longer Connects

EVO-ALL - "Died" after flashing/programming - No LEDs/No Longer Connects Updated a brand new EVO-ALL that came as part of a EVO-FORT1 kit to install into a 2015 Ford F250 pickup. After flashing and setting options/saving I connected it to the truck to program and no LEDs came on. Tried connecting back up to the updater, but it will not connect. Tried holding the programming button to do the normal reset but it shows no sign of life - Checked the connection pins and all seems fine. I grabbed another EVO-ALL I had on hand and proceeded to flash and program that unit without any issues. Could this be a bad unit that just suddenly died? I've never seen this happen.
Login to reply View 1 answer(s)

11/12/2016

 Toyota Scott Mefferd (160Pts.)

0

Cant Program Leds will not flash

red and blue led are lit and steady. Step 4 nothing happens the leds do not flash when i pres the programming button.
Login to reply View 1 answer(s)

19/11/2016

 FAQ Corey Church (170Pts.)

1

No LED's on unit after initial install

I completed all the intall wiring on my evo one on a 2007 mitsubishi eclipse, updated the bypass and remote start and when I plugged the unit in, I didn't see and LED's light up at all. Tryed to program the bypass, no LED's. removed the unit and tried to check the programming on the unit and it all seems to be fine. Looked in the Questions on the support site, and found that perhaps a master reset needs to be done. I can't seem to get any response from the unit on the car to do anything so I can't get into the programming mode to reset and can't get the red light during the master reset. What can I do?
Login to reply View 1 answer(s)

24/10/2016

 FAQ derek g (325870Pts.)

0

Ever wonder what the led's on the evo mean?

A simple and quick explanation!

Login to reply View 0 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue