Questions & Answers

When connecting my evo-all to the flash link through flash link manage I get a message saying flash link is not compatible with the device. What is up or what did I do wrong? It never gets to a screen to select vehicle just stays in the home screen with the error and the only think I can select is updating firmware to the flash link which I did. Please help.

Evo all bypass module

When connecting my evo-all to the flash link through flash link manage I get a message saying flash link is not compatible with the device. What is up or what did I do wrong? It never gets to a screen to select vehicle just stays in the home screen with the error and the only think I can select is updating firmware to the flash link which I did. Please help.

Evo all bypass module

Dear

Hello everyone. Has my subject states I called them. I have 14 compass 2.4. Since I have owned my jeep for about 2.5yrs I have nothing but problems with the factory remote start. Sometimes it works, sometimes it doesn't. I press the buttons to now end and get nothing. Doors won't unlock, or they do, but they don't lock. Try to start it it will beep twice and nothing, or I get 1 beep. 

So today I got frustrated. It beeped twice and got nothing or it beeped once. Wouldn't unlock/lock. I haven't driven it all week, been in a garage. So I called JEEP express my frustration and aggravation. And that JEEP should own up this reoccurring problem to me and others and recall the vehicles, or offer sometime of remedy. But all I got is from a lady reading me the damn manual on WHAT may cause this. I been there, done, tried it, etc... I told them that I am tempted to go see about aftermarket one and JEEP should pay for it. Glad I didn't need to get in my jeep in a hurry. I wouldn't bc the fob or whatever won't work and I was to damn busy fondling with keys. "This is not except able."

I know jeep won't do anything abt it. But at least I can say I tried. 

Just a crappy design. I think I will try an aftermarket thing to see if there is away to bypass the OEM one.

HI,

I have Evo-All + RF kit 912 on Jeep Wrangler 2012.

All works fine, very happy, but when Remote start the jeep I have an error on dash.

With obd computer the error is: B2102 - IGNITION RUN/START INPUT CIRCUIT HIGH"

I can clear the error, but at next remoted starts it come back.

With standard key the error dont appear.

Any idea to solve?

Thanks

HI,

I have Evo-All + RF kit 912 on Jeep Wrangler 2012.

All works fine, very happy, but when Remote start the jeep I have an error on dash.

With obd computer the error is: B2102 - IGNITION RUN/START INPUT CIRCUIT HIGH"

I can clear the error, but at next remoted starts it come back.

With standard key the error dont appear.

Any idea to solve?

Thanks

HI,

I have Evo-All + RF kit 912 on Jeep Wrangler 2012.

All works fine, very happy, but when Remote start the jeep I have an error on dash.

With obd computer the error is: B2102 - IGNITION RUN/START INPUT CIRCUIT HIGH"

I can clear the error, but at next remoted starts it come back.

With standard key the error dont appear.

Any idea to solve?

Thanks

I finally got my EVO-ONE and the LINKR-LT2 to remote start my 2017 Jeep Wrangler manual transmission... it works every time.. 

The only thing that technical support from mycar controls and myself haven't figure it out yet is "why after ready mode (neutral position, parking brake, brakes) the EVO-One will let me remove the key and unlock the doors or door depending of the initial command which I love (It does follow 1 passenger or more than one and unlocks the necessary door or doors depending on the remote sequence done to unlock driver's door or all doors)...back to the commandas... after I shut the door the car will kill the engine and after some seconds...I think is like 60sec. the car will lock the doors by itself.

Every time the car locks the doors...mycar control app will not show this status and only will have the green signal with doors unlocked,.. even though they are in fact locked.

Mycar control technical support told me that I have to choose an option to lock the doors with my factory remote and eliminate the automatic lock the doors command from the EVO-ONE or CAR ALARM (we are not sure who is sending the command... I think is the EVO-ONE but I need to confirm the blue led to be sure and haven't done it yet)

Can someone help me to know what setting number will set this option?,,,, The evo-one is super hidden and in order to remove it and have space to work under my steering column I have to remove the driver seat... jeep space in the front is super tight...

Thanks in advance 

Natalie