Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

2015 jeep grand Cherokee PTS using evo all climate shuts off with remote start

Installed an evo all a while ago but customer noticed the climate is off when she starts with evo all 3x lock and start 2 When she uses factory remote start or manual start climate turns on no problem It’s turning the climate off the screen says climate off even though she turns it all on before she shuts Jeep off 2015 jeep grand Cherokee diesel PTS

23/10/2024

Jeep G Trob (130Pts.)

0

EVO-All and CHRT4 - no connection type option

Greetings, Programming an EVO-ALL for install in a 2012 Grand Cherokee PTS, planning to use a CHRT4 T-harness for install. When programming the unit with the FLASH-LINK, firmware 59.02 in the section for selecting 'Connection Type', it only presents 'Wire-to-wire' option...is that correct?

21/05/2024

Jeep G M (16110Pts.)

1

2022 wrangler

Hello. I installed evo-all on a 2022 Wrangler. When registering, the decryptor wrote: "DCRYPTORS LIMIT HAS BEEN REACHED FOR THIS CAR...What should I do?

0

When i try to remote start after install a blue light flashes on module but Jeep does not start

I finished installing and programming my remote start on my 2020 Jeep Wrangler w/o keyless entry. I have the after market remote start remotes and when I go to start it a blue light flashes once on the module but the Jeep does not start. Dash screen light comes on and so does the lights by the gear selector but that’s it.

0

Why Vehicle won't start from the remote? Yellow LED on when i turn to on the ignition.

Vehicle won't start from remote after programming.

0

2017 Jeep Grand Cherokee Starts the shuts off immediately

2017 Jeep Grand Cherokee. EVO -All Inside Firmware 69.06 Hardware inside 7.0
CHR7A wiring harness. Installed according to directions and got the lights on the EVO-All as shown. DCRYPTOR process seemed to be successful.
Vehicle starts then stops within 1-2 seconds.
Are there any settings/options I should be setting?

0

Does the 2014 Jeep Cherokee char-7 harness work if it has a key barrel ignition and not push-to-start?

Will the evo-all with chr-7 harness to remote start a 2014 Jeep Cherokee that does NOT have push-to-start.

15/11/2021

Jeep G M (16110Pts.)

0

2017 jeep compass

Hello. In the manual № 98391, in the programming procedure, in the 7th step, it is written that press the start-stop to turn ON the ignition. Then it is written again, press the start-stop to turn ON the ignition ... And when did we turn it off?

0

Jeep Grand Cherokee 2015 blue light wont come back on after turning the ignition off

this is a push to start jeep I followed the steps: 1. plug in holding button 2. let go on blue and then turn the igntion on 3. after i press the button when the igition is on the blue light shuts off 4. turn the igniton off and then it is supposed to be red and blue flashign but that hasnt happened for me

0

2018 Jeep Cherokee push button start cruise comes on but won't set after install

0

‘18 Wrangler - Remote start shuts engine off when doors are off

I have a 2018 Jeep Wrangler. I installed the EVO-CHRT6 Stand Alone, vehicle remote starts and everything works fine with the doors on. Remote start the vehicle, unlock vehicle, open door, get in, close door, hit brake, lights blink twice, vehicle is not using Fortin anymore. As a wrangler owner, we take the doors off. When I remote start the vehicle with doors off I follow a similar process. Remote start vehicle, unlock vehicle, get in, hit brake, vehicle shuts off and lights blink twice, which then I'll have to use the push button to start vehicle back up. How can I fix this? The remote start needs to recognize the doors opening and closing rather than just the unlock being pressed.

0

factory alarm Problem with remote start

I have jeep grand cherokee 2013 (push to start) and install EVO-CHRT4 without the rf kit when I trun remote start it was sounding horn and hazard lamp and not stopping When trying to run the car with remotes, the alarm times work and the time does not work Update my device to 74.29 Park lights and hood pin are not installed Options: C1 D1 D6 I hope to solve the problem Best regard

0

Yellow LED flashes 5x after vehicle shutdown

using the fortin evo all as a bypass for a passive keyless entry on my 2014 jeep wrangler manual transmission. The device is set to be a bypass module and not a stand alone remote starter. Ive been able to bypass the clutch and program the device, but once i power down my vehicle the fortin module will flash yellow 5x and then it wont work till i reprogram it again. Initially it thought it was because if the clutch bypass, but that works so any help is appreciated.