Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

what's all the accessories i need to connect a fortin evo-all to 2013 JEEP CHEROKEE ( standard key )

what's all the accessories i need to connect a fortin evo-all to 2013 JEEP CHEROKEE ( standard key )

0

What connection did I miss? 2009 Jeep Compass

2009 Jeep Compass automatic. Kit is EVO-CHRT5 with a built in T-Harness and a EVO-ALL Install is complete and programming procedure completes correctly at each step. No extra sensors- no hood switch or valet switch yet. But there is no start with the remote. Vehicle starts normally with the key in the ignition. I received a code in the box for wiring color setup and had to choose from about 8 guides. The displayed numbers mean nothing as the numbers at the top of the pages when printed show something different. I am using Guide 63651. Besides the T-connections, I also connected the two yellow wires together. No other wires were connected and I am not sure what to do with the purple wire #18 as the drawing says it goes to the kick panel at item 3. What is it wired to? A troubleshooting guide says to check for power at yellow/red and yellow/blue. I get nothing when trying to start. New: I found a comment on a youtube video about hooking the green/red wire to the purple wire in the T-harness. That does not make any difference for me. Still no attempt by the car to turn on or to crank. Of course the horn honks and the doors lock each time I hit the lock button.

0

Why or how csn i flash my evo all for my 2013 jeep patriot

How do I know my evo all is flashed correctly

0

2008 Jeep Patriot Evo-Alll slow flashing blue light

Here is what I have: 2008 Jeep Patriot Automatic Transmission, EVO-ALL, ProStart CT4311-TW, Jeep Patriot T-Harness. After programming evo-all, it only slow- flashes Blue LED. CT-4311 is connected D2D to evo all. Yellow ignition wire from CT-4311 connected to Evo-All yellow ignition wire connected to yellow t-harness wire. purple Mux wire connected to evo all. CT4311 park lights wire wired to Jeep parking lights (white/purple) when 3 lock press on factory remote.....nothing, slow flashing blue light. when lock button on CT4311 remote pressed, CT-4311 clicks, no lock, park lights flash 1 time when unlock button on CT4311 remote pressed, CT-411 clicks, no unlock, park lights flash 2 times when start button pressed, ignition comes on, dash lights up, no start, no crank. Repeats 2 more times. any suggestions? I am thinking there must be something in the settings/options of EVO-All. I have the programmer and software. I just selected the "default" options when flashing. thanks Mike

0

EVO-ALL Hardware 7 - Jeep J1850 protocol

Hello, I bought an EVO-ALL (Hardware version 7), however I would like to use it on a 2001 Jeep Grand Cherokee ...

From the site documentation I see that you have to use a version 4.06 maximum (not available on hardware version 7) From some information I saw that the J1850 protocol has been reintegrated from version 7.74.22, I want to know if all the other more recent versions are also equipped? (To date the most recent version is 7.88.10) thank you in advance

0

Manual transmission ready remote start

I have a 2017 Wrangler and after completing the hood pin switch and the installation of the siren, I finally tried to test the remote start methord

Using the factory keyless remote lock-unlock-lock....after several seconds...nothing happened 

Using the LINKR-LT2 mycar control app after several seconds from blue turned into red and nothing happened. 

I am assuming my reqdy mode procedure will be to have the engine running,  transmission in neutral,  pressing the brake, engaging the parking brake, release the brake pedal, turn the engine off then open the door and leave setting the alarm to lock the car.... but the engine shut off as soon as I remove the key from the ignition.

 

What am I doing wrong?

S/N 002B04043387

 

0

2018 Jeep Cherokee push button start cruise comes on but won't set after install

04/12/2018

Jeep Shane h (130Pts.)

0

2017 Cherokee Not starting

I programmed the entire unit but the vehicle refuses to start. The evo all module blinks blue when i press the lock button. I dont know what else to do please help.

0

what is the black data plug wire colors and funtion? Cat get past step7 in programming.

2016 Jeep Cherokee stand alone remote start. using evo all & chrt 6 Tharness i get to step 7 but blue light never comrs on. also can you tell me the function of the 4 wires in the black data plug? this harness did not have te plug so I found a plug that fit and wired the red wire to 12 volts, the black wire to ground, do I need the other 2 wires? if so what are their colors and function? Thanks

0

2004 Jeep Red Light Doesnt Come On

After installing the EvoAll with connection 1 and attempting to program with program 1 the blue lighht turns off but the red light doesnt come on. What would be caussing this?

0

What Options to program for '07 Wrangler automatic trans

What options should be selected as default for a stand alone installation in a 2007 Jeep Wrangler with auto transmission? I've been checking and unchecking boxes for several days now trying to figure it out. Currently, after remote start then turning off vehicle, about 3 seconds later the horn beeps and the doors lock. Problem is my keys were stiil in the vehicle and I had already exited the Jeep.

0

Evo All with THAR-CHR5 harness and door problem

I am using the EVO-All as a stand alone on a 2006 Jeep commander. In order to simplify the transducer connections I am using a THAR-CHR5 harness. I wired it according to guide EVO=CHRT5 schematic F. I have programed the evo all as a stand alone and set the option to unlock then lock after remote start. The car does remote start with 3 key presses of the oem remote. I have detected 2 problems with the doors. First off it will remote start with the doors open and with the doors closed it will unlock the doors but not lock them after a start. It also does not shut down with a brake application. Should I have not used the T-harness and wired it according to Guide 8141 connection 2 and not used the T-harness?

0

Evo All with THAR-CHR5 harness and door problem

I am using the EVO-All as a stand alone on a 2006 Jeep commander. In order to simplify the transducer connections I am using a THAR-CHR5 harness. I wired it according to guide EVO=CHRT5 schematic F. I have programed the evo all as a stand alone and set the option to unlock then lock after remote start. The car does remote start with 3 key presses of the oem remote. I have detected 2 problems with the doors. First off it will remote start with the doors open and with the doors closed it will unlock the doors but not lock them after a start. It also does not shut down with a brake application. Should I have not used the T-harness and wired it according to Guide 8141 connection 2 and not used the T-harness?

02/01/2016