Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

12/11/2024

 Hyundai Christopher Barrow (130Pts.)

0

2013 Hyundai Genesis Coupe auto- Alarm going off after remote starting

Had the EVO ONE installed for about a year with all the functions working. The engine locked up and after the dealer replaced it everything still works except when you remote start about 20ish seconds past and the car alarm will go off. I've tried changing some settings, the master reset ( plug in the big connector and let the button go when its red then hold again until it cycles) then flashing it again still no change. I checked the wiring and found no breakage or cuts. 2 things I've noticed is that if I'm trying to do the KEY BYPASS PROGRAMMING PROCEDURE after I get solid yellow and I plug in the rest of the connectors and turn the car on the light does not change, tried about 4 times, but when I do the PROGRAMMING VEHICLE WITHOUT PATS DATA WIRE (even thought I did the PATS wiring like the diagram said) I get through all the steps no problem and end up with the original issue. 2nd thing is when I remote start it unlocks then locks and starts (like it should) then after a couple of seconds it locks again which I feel like its arming the alarm because I tested unlocking the car after that second lock and around the time the alarm would normally go off it doesn't but what happens is the car relocks its self then after some seconds the alarm goes off again. Also note if I turn the alarm off the cycle of the car locking itself again then the alarm going off will continue forever until I either disable the remote start or put my key and turn it to the on position To me its sounding like the EVO one isn't acting like the "key" which points to the key bypass Issue and I cannot seem to find a forum about the problem I am having
Login to reply View 1 answer(s)

24/05/2024

 Hyundai Erika Eugenio (180Pts.)

0

Fortin Evo Start - No fuel reading - 2012 Sonata

Installed Fortin EVO ALL + Fortin EVO Start. Everything works except for fuel gauge reading on app. 

I am able use all available app functions for remote start, door close, lock/unlock, GPS, internal temperature. On the App I am unable to get fuel level to be displayed. (see attached screenshot) 

https://photos.app.goo.gl/pi3MAUQ8rGQbjYpM6

Login to reply View 1 answer(s)

26/03/2021

 Hyundai Kevin Raymond (250Pts.)

0

Evo One won't start after 5 min or so but was working right after key bypass programming procedure

Hi, I'm kind of lost here, nobody seem to have the answer to my problem, not even Fortin when I call them for help. I installed my Evo One on my Hyundai Tucson 2020 standart key start, followed exactly all the wiring as per the guide, double check all my connection (EMS, CAN BUS, ignition wires, etc) and there's no loose cable. After that I did the key bypass programming procedure with EMS cable : hold down program button while plugging the 6 pin heavy gauge wire till it was red, plug all the others wires, press 7 times program button till it flash 6 times every second, put the key in and turn to ON. At this point the red led flashed 10 time quickly and after stayed on while the blue light started flashing quickly too. After that I turned Ignition to OFF and every light turn off. Right after that I tried to start the car by pressing LOCK, UNLOCK, LOCK and the car started no problem. I then stop the car, close the door and wait... 5 min later, I tried to restart the car with the remote starter but it didn't work. The car got the lock unlock lock signal but no light is flashing on the module anymore like if it went into sleep mode or something. I tried many thing and here is what I found out : - If I unplug all cable from the Evo One and plug it straight back it then start receiving signal again for the next 5 min or so. - If I open the trunk and close it back, the module seem to start back receiving signal from oem remote. To me it feel like there is a cut off or something that stop the module from receiving any signal from the oem remote after a certain amount of time, kind if it was to prevent from draining the battery of the car. Could also be that the Evo One is loosing the key programming after current shutting off in the car but then it shouldn't start by just unplugging and replugging the 6 pin ignition wires. *Sorry if my english is not perfect, I usually speak french.
Login to reply View 2 answer(s)

26/03/2021

 Hyundai Kevin Raymond (250Pts.)

0

Evo One won't start after 5 min or so but was working right after key bypass programming procedure

Hi, I'm kind of lost here, nobody seem to have the answer to my problem, not even Fortin when I call them for help. I installed my Evo One on my Hyundai Tucson 2020 standart key start, followed exactly all the wiring as per the guide, double check all my connection (EMS, CAN BUS, ignition wires, etc) and there's no loose cable. After that I did the key bypass programming procedure with EMS cable : hold down program button while plugging the 6 pin heavy gauge wire till it was red, plug all the others wires, press 7 times program button till it flash 6 times every second, put the key in and turn to ON. At this point the red led flashed 10 time quickly and after stayed on while the blue light started flashing quickly too. After that I turned Ignition to OFF and every light turn off. Right after that I tried to start the car by pressing LOCK, UNLOCK, LOCK and the car started no problem. I then stop the car, close the door and wait... 5 min later, I tried to restart the car with the remote starter but it didn't work. The car got the lock unlock lock signal but no light is flashing on the module anymore like if it went into sleep mode or something. I tried many thing and here is what I found out : - If I unplug all cable from the Evo One and plug it straight back it then start receiving signal again for the next 5 min or so. - If I open the trunk and close it back, the module seem to start back receiving signal from oem remote. To me it feel like there is a cut off or something that stop the module from receiving any signal from the oem remote after a certain amount of time, kind if it was to prevent from draining the battery of the car. Could also be that the Evo One is loosing the key programming after current shutting off in the car but then it shouldn't start by just unplugging and replugging the 6 pin ignition wires. *Sorry if my english is not perfect, I usually speak french.
Login to reply View 2 answer(s)

10/01/2021

 Hyundai Stephen Renna (260Pts.)

0

2019 veloster push to start not working

I just installed the Evo-One with the T harness. I programed the Evo and the started the car. Followed the reservation mode and the hit the push to start button and the car shuts off! I notice that when the car is on the Evo-One only shows a orange/yellow light, that's it. Please help.
Login to reply View 0 answer(s)

08/05/2019

 Hyundai Brandon Houston (190Pts.)

0

2016 Hyundai Accent won't start with t harness install

My car will start with key but not remote start theBLUE LIGHT STAYS ON CONNECT REST OF CONNECTORS TURN KEY ON LIGHT GOES OUT turn key off blue light goes back on can voltage is 2.7 and 2.5
Login to reply View 1 answer(s)

08/05/2019

 Hyundai Brandon Houston (190Pts.)

0

IS AN RF KIT NEEDED WHEN INSTALLING INTO 2016 HUNDAI ACCENT STANDARD KEY W/ T HARNESS

I have a 2016 Hyundai Accent standard key Evo One with a t harness is a rf kit needed for installation
Login to reply View 1 answer(s)

26/04/2019

 Hyundai Sebastien Bordeleau (240Pts.)

0

Auto usagé avec evo start problème...

Bonjour, j'ai acheté mon Auto usagé au concessionnaire kia. Et l'auto vien avec evo start. Le code actuel est utilisé par l'ancien propriétaire . Donc comment retirer l'ancien propriétaire si j'ai zero possibilités de contact avec lui....?

 

Merci

Login to reply View 1 answer(s)

20/10/2018

 Hyundai Rogelio Abraham2 (270Pts.)

0

Evo one, remote started run's and quit in 5 seconds

Evo one, remote started with RFkit RM411 runs but quit in 5 seconds ( remote starter attempted twice ) and failed. whats wrong? please help..
Login to reply View 1 answer(s)

17/01/2017

 Hyundai Neseth Kong (200Pts.)

0

Evo One can't Program Compustar G9 2 way

I have an EVO ONE which i installed in my 2016 Tucson with the T harness.  The wiring was minimal and straight forward, so I know it's all correct.  It's just 4 CANbus wires, parking lights, horn, and ignition.  The dealer I bought it from programmed it for a Revo 1.1(fortin2) but I couldn't get that to work.  I followed the procedure for the valet button and brake pedal, the car responds and flashes the lights when it's supposed to, but wouldn't respond when pressing the start button on the Revo.  So I sent those remotes back to the dealer to be replaced. 

While waiting for the replacement remotes, I was at best buy and spotted the compustar 2 way system (RF-2WG9-SP).  I bought it and ordered the flashlink2 unit online.  First, before the flashlink arrived, I swapped the 4 pin wires and programmed the remotes with the EVO ONE still set to fortin2 and firmware 1.21, and the compustar remotes WORKED.  I could Lock/Unlock my doors and hatch, as well as start the car.  The car responds exactly as it should with the lights and horn.  The problem is it only works as a one way remote.  The blue compustart remote is supposed to be one way, but the orange remote is supposed to give me a 2 way response.  However, at least I know all of my wiring is correct. So the problem is communications handshaking between the box and the remotes.

So my Flashlink comes in and i'm able to switch the options to firsttech from fortin2.  I tried to program the remotes on mode 1 and mode 5, but no success.  I tried to do a full master reset and flashed the firmware to 0.96.  I set it to firsttech in options and tried to program on mode 1 but didn't work.  So i did a master reset, set options to firsttech and tried to program on mode 5 but no success.  So I set it back to fortin2 and it programmed on mode 5 on the first try.  Everything works again except only as a 1 way remote.

Any ideas, I figured it would be straight forward to program this remote?

Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue