Questions & Answers

It's like a false/positive situation. I had someone overpress my rf remote and oem key was starting car on one lock. blah blah blah

Reprogrammed both sets of keys (2 oem's and 2 RF RM411 long range one way remotes). Everything works fine again, but if I use the one button RF RM411 I get the code thrown and a little red security light stays on for a couple of seconds once my key is in on position in ignition.

Now if I just use the OEM key, I don't get the red light. Also there is no engine light with code. The only reason I know it's there is I had the car seafoamed (should have done through break booster after MAF, used intake manifold. Had engine lights galore and ended up changing all 16 spark plugs myself (the good ones) and clearing misfire and crankshaft sensor codes.

Anyways, all is working great now, except this code I can't seem to clear in any way. Is this an issue with my car or Chrysler products? 

Usually when you have this code, the car will start but quit soon after.

Just let me know and I will just leave it alone and not worry about it.

Please do my a favour. Talk to me like I'm 7 and give me the step by step process of installing the valet switch.

1. connect which side of the wire to A13 (I'm thinking the black wire with grey checks (positive side). 

2. find a metal piece and attach wire that is black to a screw and fasten it.

3. Mount switch (where most people mount this). 

I'm having some recall work done with the air bag inflators on Nov 12th from the dealer. Also curious how to install this thing properly,

I have fully installed wiring using Military Splice method with a stripping tool. Each wire has 3m electrical tape and a small zip tie. So clean the military would be proud lol.

I have triple checked the wiring and everything is right. I think we're at a point that you need to look at my Service Tag # 001A07135564. 

This car will not remote start, shouldn't be this difficult. Perhaps a bad T-Harness???  

I see you used my ignition harness picture on WireColor.com lmao, maybe you should have waited. Also  see you revised the install guide as well using my info. If the car won't start, how is this helping?

I went over the colour of each wire several times to be sure before I made this post. HELP! 

I have fully installed wiring using Military Splice method with a stripping tool. Each wire has 3m electrical tape and a small zip tie. So clean the military would be proud lol.

I have triple checked the wiring and everything is right. I think we're at a point that you need to look at my Service Tag # 001A07135564. 

This car will not remote start, shouldn't be this difficult. Perhaps a bad T-Harness???  

I see you used my ignition harness picture on WireColor.com lmao, maybe you should have waited. Also  see you revised the install guide as well using my info. If the car won't start, how is this helping?

I went over the colour of each wire several times to be sure before I made this post. HELP! 

My ignition wire setup as follows. 1. Purple/Orange

                                                     2. Purple/Brown

                                                     3. Pink/White      (Now says Pink)

                                                     4. Pink/Green     (Now says Pink)

                                                     5. LTBlue/Red

Module and RF kit (RM411) is programed and works fine. When I remote start I get a blue light for each lock press on OEM remote. 

Then it unlocks and locks and get RED and YELLOW lights with bottom blue flashing I hear the chime and it tries to engage without starting.

I know I can't be the first 300c first gen owner that has had this problem, any help would be greatly appreciated. I can share the video of the starting sequence (email or onedrive link).  Thanks

https://1drv.ms/u/s!AglxCUFWL4h7k_RVT52kACjno0_xIA        (pic of Ignition plug)

Right click links and choose open in new window to stay in forum

I got it to remote start fine. But I unhooked it to put my dash back together and do cable management and then once I put it back together i tested it again. It then would only flash the lights. I kept repeating the process to remote start and it would work. And then it kept repeating this process to the point where it wouldn’t start at all. So I assume maybe I knocked a wire loose. Any idea what it would be?