Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

13/12/2023

 Ram Paul Carnaby (130Pts.)

0

Evo-Can remote start

I have a Evo-Can module that has never been used is it possible to use this as a standalone remote start on a 2009 Dodge Ram Sport gas engine? I have searched endlessly for information which little to no information I also have the THAR-CHR4 harness that is supposed to work with the module . When I search for wiring diagrams they all show the Evo-All or Evo-One module any assistance would be greatly appreciated if the Evo-Can module can be used,is it possible to still flash the module with required data?

Login to reply View 1 answer(s)

30/12/2019

 Ram joe waldon (130Pts.)

0

Can the evo all turn on heat qhen remote started?

Evo all works perfectly starting the ram 1500 just dont turn on heater of heated seats if cold out
Login to reply View 1 answer(s)

25/01/2019

 Ram Radoslaw Patora (740Pts.)

0

RAM 2500 DIESEL KEY+EVO ALL - REMOTE NOT WAITING FOR A GLOW PLUG

RAM 2500 2014 6.7 DIESEL + EVO ALL STAND ALONE 3X LOCK REMOTE START WORKS FINE BUT AFTER IGNITION ON DOES NOT WAIT FOR GLOW PLUG C1,D1,D2 ,AND DIESEL MODE IS ON
Login to reply View 1 answer(s)

07/01/2019

 Ram Loren Malcom (160Pts.)

0

Wired correctly, works, but dash goes nuts.

I have a 2014 ram 1500 with a tip key. I have the chrt6 evo all. Everything is hooked up correctly. But after it’s started the check engine light now is on and a bunch of other light come on including the TPMS, traction control, saying my fuel gauge sensor is bad. Blinker light on the dash not working. Etc... The directions call for a diode but doesn’t show where to put it in the schematics. Is this my issue? PLEASE HELP!
Login to reply View 1 answer(s)

04/12/2018

 Ram Joshua Wilson (190Pts.)

0

the dcrypter wont program.

i programmed my Evo-All on my 2018 ram 2500, however when i went to dcrypt the module, it never finishes processing the update, just spins continuously.
Login to reply View 1 answer(s)

01/11/2018

 Ram Jacob Marquis (130Pts.)

0

Car shuts off with key in ignition- 2016 Ram 1500

When I remote start with key then get in and put key in run possition the truck shuts off. Tried both keys, tried turning to start possition. Evo all. Have a 2016 ram 2500 diesel and using key that was not used to program it works .
Login to reply View 1 answer(s)

03/04/2018

 Ram Karl Ford (310Pts.)

0

Flashlink 2 and Evo All not connecting to computer

The red light is on thr FL2 and the Blue light is flashing on the EVO All when connected. I did a full reset after I tried to do the Smart Start install. Got all connections right but didnt know i needed Dealer assistance. (VSM200) The EVOALL was Warm to the touch after install attempt so I disconnected and then RESET.Then started from scratch till I got BSLOW FLASHING BLUE LIGHT... When i tried to reflash it..NADA...It's in ByPASS mode, i uninstalled and reinstalle the flash manager...even tried different computer. Did i do something wrong with the remote Start? DID i Fry something even though EVERYTHING works up to the flash point? TIA
Login to reply View 1 answer(s)

01/04/2018

 Ram Karl Ford (310Pts.)

0

Want to connect Evo All to VIPER 5901 AND Smart Start.....Need help with Install

I have my EVO ALL in my 15 RAM. I have a Viper 5901 that I want to ADD to it. I know the 3 main wires are the power and the Ground, and the hood Pin. I thought connecting the 4 pin connector to the Viper brain would be the start but I cant get the Antennae to flash. I took the EVO ALL module ot to Flash if but Im not Sure if I'm to turn it OFF because the 5901 would be recieving the signal and sending it to the EVO or not. Am i on the right track? Also how do I add the Smart Start modual......I prefer to do things myself and avoid $300 to add this Thanks in advance.
Login to reply View 1 answer(s)

12/11/2017

 Ram tim jankowski (130Pts.)

0

blue light wont flash after install

I connected everything the way it was supposed to be except for the data cable that is supposed to go to a rf antenna. I cant find one on my vehicle and am using my evo all with t harness as a stand alone remote start. I had to splice the red and black to a ground and power to get it going but the other two are not hooked to anything. I got it programmed correctly and when i hit the 3x lock it doesnt start or do anything.I have checked all the wires and everything is connected good and right. When i plug in the unit after plugging it into my computer all of the lights flash about 15 times then go off. I am not sure if I missed something but any help would be great. Thank you.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue