Questions & Answers

I have a Evo-Can module that has never been used is it possible to use this as a standalone remote start on a 2009 Dodge Ram Sport gas engine? I have searched endlessly for information which little to no information I also have the THAR-CHR4 harness that is supposed to work with the module . When I search for wiring diagrams they all show the Evo-All or Evo-One module any assistance would be greatly appreciated if the Evo-Can module can be used,is it possible to still flash the module with required data?

Hello, I am looking to get remote start only for my '19 Ram 1500 promaster. It does not have remote start or alarm now. It uses a standard turn key. According to the website it says I can use the EVO-ONE. Looking at the install instructions on page 5, it shows what looks to be a remote starter module of some sort?

Am I looking at the right instructions for this setup?

If so, do I need another part?

Also, is there a t-harness made for this yet?

Thanks!

2014 ram 1500 (standard key start) after successful programming, vehicle can be remote started by 3x lock only....H2 - fortin 2 is selected on in flashlink setting, ascl6 app protocol is set to fortin, RFA2A adaptor is connected but still no luck, both red and green led on ascl6 are on solid, been trying to get the evo all to pair with ascl6 with no success.

evo all led lights are stuck at step 8, will not go to step 9 

1 - Disconnect the Black 4 pin power connector from the Evo-All.

2 - Press and Hold the Programming button on the Evo-All while plugging back the Black 4 pin connector.

3 - The LED’s on the Evo-All will begin to cycle. Keep pressing the programming button until the RED and BLUE LED’s are On.

4 - Release the programming button.

5 - Press and Hold the programming button again for 5 seconds. The BLUE and RED LED’s will blink once.

6 - Release the programming button.

7 - Cycle the ignition to the ON position.

8 - The RED, YELLOW and BLUE LED’s will be ON.

9 - Seconds later the RED and BLUE LED’s will blink once to confirm that the MyCar ID has been learned to the Evo-All.

10 - Cycle the vehicle’s ignition to the OFF position to Exit EVO-ALL programming.

Today I tried installing the Evo-All to a 2016 Ram 3500 diesel using the T-harness. I made it to step 7 and could not get past that. 

In step 7 it says “No key = Red” and “Key in= Red and blue”. Whenever i put the key in, the red and blue will stay on for a few seconds then only the blue will stay on. Is this supposed to happen?

I then put it into the RUN position but it will not flash rapidly. If I put it back into OFF, the blue will go back to solid.I checked the CANBUS wires multiple times and made sure they were at the right spot. I even switched them. In step 8 it says “ignition off= red” and “ignition on= red and blue off”. I dont see a red light after step 7 but the blue does turn off when the ignition is on.  One thing I did notice though was that the CAN-HIGH wire Grey/White Pin6 on the guide is a different color on my truck; its sort of a tan color but it is still pin 6. The yellow wire DOES match up. Would this have to do with anything?

I followed the intructions on how to test the CANBUS connection and ignition(https://fortin.ca/en/qa/403/programming-evo-all). The ignition is good but whenever I put it in RUN, the blue light will not flash so im sure its a CANBUS problem i just cannot figure out what it is. I also tried resetting the module and it did not work. I updated  it to the latest firmware and even dropped it down to the one it says on the guide but that did not work either. I also tried waiting in between the steps and no luck. Any help is appreciated.