Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

08/12/2024

 Ram Dinh Doan (160Pts.)

0

2017 Ram 1500 Start briefly then shut off

Installed the fortin evo all with THAR-CHR7 and a 5706v w2w. Programmed according to instructions. Everything is working properly except I can't get the vehicle to remote start every single time. It starts and shuts off right after starting. Sometimes the truck will remote start and stay running like it should but not everytime. What could be wrong? Is it the firmware version?
Login to reply View 1 answer(s)

27/09/2024

 Ram Ramy Fathi (230Pts.)

0

Does CHRT7 require any splicing or tapping for a 2024 Ram?

Considering buying a CHRT7 or CHRT6 for my 2024 Ramy 1500 Rebel with OEM remote start and keyless entry. I looked at the install guide, but its not quiet clear whether it requires splicing/tapping into any wires. (especially the parking lights, ignition, CAN low and High). Thanks
Login to reply View 1 answer(s)

26/11/2023

 Ram G M (16110Pts.)

0

dodge ram

Hello. I want to install fortin on a 2023 Dodge Ram. Can I use the instructions from Ram?
Login to reply View 1 answer(s)

18/10/2020

 Ram John Coelho (130Pts.)

0

How do I set the delay for the glow plugs to warm up?

I have the module set to diesel mode and the delay after pushing LOCK LOCK LOCK is only about 6 seconds. My truck has a glow plug monitor which tells you when its okay to start your truck, and on cold days, ie 35 degrees and below, the delay for this remote start is not long enough.
Login to reply View 1 answer(s)

14/02/2020

 Ram Michael Dolan (130Pts.)

0

Programming for diesel

I just purchased a chrt4 for my 2010 ram 2500 diesel. The ad stated it was not programmed so I purchased the flash link as well. Will I be able to program if for the diesel delay?
Login to reply View 2 answer(s)

14/02/2020

 Ram Michael Dolan (130Pts.)

0

Programming for diesel

I just purchased a chrt4 for my 2010 ram 2500 diesel. The ad stated it was not programmed so I purchased the flash link as well. Will I be able to program if for the diesel delay?
Login to reply View 2 answer(s)

14/10/2019

 Ram Engineering Department (130Pts.)

0

EVO-CHRT6 for RAM 4500 Diesel, brake pedal wont work for remote start.

When you request engine start with either the remote or the external activation wire it will not start, only when you hold the brake pedal will it engage. Once the engine is started, engine will not shut down with brake pedal or external activation wire.
Login to reply View 1 answer(s)

04/10/2018

 Ram Elizabeth Kingston (160Pts.)

0

2014 Ram 1500 crimestopper revo 1.1 hangs on yellow when programming remote

installing a revo 1.1 remote starter on my Fortin Evo All unit chrt6 on my 2014 ram 1500. when programming the remote units i unplug the power cable. hold program button and plug power cable back in. i get a solid red and solid blue. i press the program button and hold until the blue and red lights flash out and come back on. I put the key in the ignition and turn to run position i get a solid yellow. red and blue are still lit. when i push the button on the remote unit to pair to module the red and blue light are suppose to blink to acknowledge the remote unit has been programmed. on my unit the red and blue light go out and only the yellow light remains on. firmware 74.37. In my flash link setting under data protocols everything is greyed out i cannot select F2
Login to reply View 2 answer(s)

04/10/2018

 Ram Elizabeth Kingston (160Pts.)

0

2014 Ram 1500 crimestopper revo 1.1 hangs on yellow when programming remote

installing a revo 1.1 remote starter on my Fortin Evo All unit chrt6 on my 2014 ram 1500. when programming the remote units i unplug the power cable. hold program button and plug power cable back in. i get a solid red and solid blue. i press the program button and hold until the blue and red lights flash out and come back on. I put the key in the ignition and turn to run position i get a solid yellow. red and blue are still lit. when i push the button on the remote unit to pair to module the red and blue light are suppose to blink to acknowledge the remote unit has been programmed. on my unit the red and blue light go out and only the yellow light remains on. firmware 74.37. In my flash link setting under data protocols everything is greyed out i cannot select F2
Login to reply View 2 answer(s)

06/09/2018

 Ram Joshua Lindt (260Pts.)

1

2017 Ram 1500 Tip Start, Will Not Remote Start

Details: 2017 Ram, Gas, Tip Start, CHRT6, OEM Remote Flashed with standalone, T-harness, with built in alarm, 74.[37] firmware, 6.0 hardware. No hood pin, valet switch, or parking lights connected. C1 and D1 enabled, #8 blue wire does not turn red when grounded. Everything seems to be installed correctly. The key programs without issues. Flashes without issues. The blue light falshes each time the lock button is pushed. The yellow light comes on when it is started with the key. Problem: When I attempt to remote start (3x lock button on the EOM remote) nothing happens on the unit or in the truck. No attempt to start, no dash lights, nothing. Any advice?
Login to reply View 1 answer(s)

26/05/2018

 Ram Mitch Harvie (160Pts.)

0

Ram alarm

 

 

I turned function 14 mode 2 on on my 2014 ram. After double locking car alarm still doesn’t sound or activate after opening door from inside. Is there something I am missing? Can I not use the factory horn? And if I can do I have to hook it up or will it work through can line 

.

Login to reply View 1 answer(s)

02/02/2018

 Ram Matthew Oakley (130Pts.)

0

2014 ram 1500 standard key, wont stay running after key is put in and turned

i installed a prostarter remote start with a fortin evo all. after starting with the remote start and i go to drive, i turn the key and step on the brake to put in drive and truck shuts off and needs to be restarted, also sometimes it will only start and run a few secs and shut off. but if i cancel it and retry it will run for preset time on install.
Login to reply View 1 answer(s)

10/01/2018

 Ram DAVID WALTERS2 (230Pts.)

0

After installing EVO-CHRT4 on a 2010 Dodge Ram, factory OEM FOB doesn't always lock or unlock doors

Installed as stand-alone just the other day and flashed the correct firmware. 3X remote start worked fine and the factory key fob would lock or unlock the doors ok. Now it will not work unless you repeatedly press a unlock or lock button. Once you get it working, then it works fine until the next day, then same problem again.
Login to reply View 1 answer(s)

08/01/2018