Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

27/04/2024

 Dodge justin squires (130Pts.)

0

Searching for a better diesel module 07 ram 2500

Looking for a module for 2007 ram 2500 diesel that has adjustable crank and wait to start times. Initially installed the evo all with t harness. It doesn't have an option that waits long enough to start, also cranks too long making the starter drag.
Login to reply View 1 answer(s)

04/08/2021

 Dodge danielfletcher0331@gmail.com (210Pts.)

0

2010 ram 2500 6.7 turbo diesel. intermittantly mis starting.

i have the evo-all chrt 4 T harness have it flashed with the newest firmwhere and followed the instructions on splicing the yellow wires together and plugging everything in. the first time i used it it worked flawlessly. but now every once and awhile after sitting like when i get out of work, and trigger the remote start, it keep hitting the starter, like it will crank the engine half a turn and stop, then hit the starter again, and again, and again, and then finally crank the enigne over and start. I am afraid this is going to damage the starter. is this possibly a bad module or flash... i hooked it back up to my pc and all settings are correct.
Login to reply View 1 answer(s)

26/11/2019

 Dodge Ryan Aaron (130Pts.)

0

2006 Dodge Ram Diesel

Hello i have a 2006 dodge ram 2500 5.9 cummins. I just got the EVO-CHRT5 kit for remote start only and tried installing it as per instructions and nothing worked. I found a youtube video where some plugged the t-harness in and spliced the two yellow wires together and spliced the purple wire with the green/red from the 20 pin connection. the truck horn cherps, and fuel pump turns on but gauge cluster wont work and truck wont turn on. I have the flash like and updated it with the newest version and activated the d.1 setting for diesel trucks. Any help would be much appricated.
Login to reply View 2 answer(s)

31/01/2021

 Dodge Stephen Detmar (130Pts.)

0

2009 Dodge ram, I looked at the guides and install going by them but all i get is all 3 leds flash

Please help frustrated
Login to reply View 1 answer(s)

02/04/2014

 Dodge (Pts.)

1

Any chance this will work with a Ram Promaster?

2014 Ram Promaster
Login to reply View 2 answer(s)

27/10/2020

 Dodge andrew reyes (160Pts.)

0

does the brown/white (-) parking light out need to be connected?

seems to work properly without it connected i see the photo on the wiring but my plug does not look the same it only has one of each color. 2006 dodge ram EVO RS
Login to reply View 1 answer(s)

29/12/2019

 Dodge Mark Perestrelo (160Pts.)

0

2007 Dodge Ram 2500 Diesel 6.7L starter continues cranking for a couple of seconds after the engine is running

I installed the evo all with the T harness today, when I start it the starter is staying engaged too long. I installed the same kit acouple of years ago in a similar truck and did not have this issue with the over crank. I saw a previous question that says this issue is normal. Is it possible to go back to a previous firmware version as I dont not want to cause unnecesary wear and damage to my truck.
Login to reply View 1 answer(s)

19/12/2019

 Dodge Emmanuel Padsican (480Pts.)

0

How do i connect a relay for the door unlock and lock for a dodge ram?

The truck is 1500 v8 2008.
Login to reply View 1 answer(s)

26/11/2019

 Dodge Ryan Aaron (130Pts.)

0

2006 Dodge Ram Diesel

Hello i have a 2006 dodge ram 2500 5.9 cummins. I just got the EVO-CHRT5 kit for remote start only and tried installing it as per instructions and nothing worked. I found a youtube video where some plugged the t-harness in and spliced the two yellow wires together and spliced the purple wire with the green/red from the 20 pin connection. the truck horn cherps, and fuel pump turns on but gauge cluster wont work and truck wont turn on. I have the flash like and updated it with the newest version and activated the d.1 setting for diesel trucks. Any help would be much appricated.
Login to reply View 2 answer(s)

17/02/2019

 Dodge Noel Martinez (130Pts.)

0

Sequence of lights and sounds then solid red and lock (06 dodge ram 1500)

So i installed my Tharch5 with T harness into my 06 dodge ram 1500, everything worked out as it should have and i had no problems, untill trying to remote start! after pressing lock three times the module runs through each light and i can hear my truck begin the process of attempting to start then nothing. i believe it tries twice before staying on the red led a couple times then locking the doors. anyone having this or similar issues?
Login to reply View 1 answer(s)

28/12/2018

 Dodge Vlad Andryeyev (130Pts.)

0

MUX Data or Ground, Dodge RAM 2007

Hello! From Wirecolor.com - pin 46 MUX Data (Purple/Brown), pin 47 MUX Ground (Purple/Orange) - What the pin should I use? Thank you!
Login to reply View 1 answer(s)

03/12/2018

 Dodge Matvey Adz (200Pts.)

2

2015 Dodge RAM 1500 diesel won't start (all LEDs flash 25 times)

Hi, I tried multiple times to get the EVO-ALL module programmed / key decrypted, and after each attempt, after plugging in the module causes all 3 LEDs to flash 25 times, and the module does not respond to the key fob. I am using this installation manual: http://cdn02.fortin.ca/download/29301/evo-all_ig_thr_bi_chr6-ram_2013_key_e_29301.pdf Verified all connections multiple times. Please advise what can be done to fix this. Thank you!
Login to reply View 1 answer(s)

15/11/2018

 Dodge Kevin Heuchert (160Pts.)

0

Key takeover Ram Evo All

Hello installed Evo All & Remote start with T harness as per wiring instructions in 2009 Ram 1500 5.7L. Everything works except key takeover after remote start...starter kill is active when key is turned to start, brakes don’t disengage starter, blue antenna lights keep flashing while driving, vehicle is operable and drivable in remote start mode. The only way to shut the vehicle off is to use the fob start button to turn off remote start. Any insight to this would be appreciated.
Login to reply View 1 answer(s)

06/01/2018

 Dodge Dan Barendregt (130Pts.)

0

Can the parking light wire be hooked up to another source?

I have a 2010 Ram 2500 with gas engine. I have a set of Rock lights underneath my truck for an awesome look when it is parked. Can I hook up the Signal wire from the 20 pin harness of a EVO-CHRT4 to these lights instead of to the parking lights? these Rock lights draw 4.5 amps. Could I connect the signal wire to the ground of these rock lights?
Login to reply View 1 answer(s)

26/03/2018

 Dodge Scott Perry (200Pts.)

0

2017 dodge ram 1500 tip key, will the evochrt6 work and is the flash loader needed also?

Want as close to plug and play & only want 3x tap remote start
Login to reply View 1 answer(s)

07/01/2015

 Dodge kevin oliva (210Pts.)

0

starts then shuts off

i have a 2010 dodge ram 1500, 3X lock starts it up and then it shuts off after a few seconds. read other posts and messed around with some options but still shuts down after start. i used the chrt4 harness with the evo all..
Login to reply View 2 answer(s)

01/02/2014

 Dodge (Pts.)

1

Key fob doesn't work after remote start. Key takeover doesn't work

I installed the evo all on a 2013 ram 1500 tip key I followed all instructions. For some reason after remote starting the factory key fob will not unlock or lock the truck. The key take over dose not work I put the key in the turn it to on/run depress the brake and the truck dies. There are lights that come on the evo when starting and when lock and unlock. Is there anything I'm doing wrong? How can I fix this?
Login to reply View 2 answer(s)

04/03/2017

 Dodge Charles Jones (130Pts.)

0

Problem programing 2012 ram

I am installing in stand alone mode but when it comes to programing ignition when I turn the key to the run position blue light flash rapidly, when I turn to off position it continues to flash rapidly when I hit lock button on remote blue light keep flashing but slower.
Login to reply View 2 answer(s)

04/03/2017

 Dodge Charles Jones (130Pts.)

0

Problem programing 2012 ram

I am installing in stand alone mode but when it comes to programing ignition when I turn the key to the run position blue light flash rapidly, when I turn to off position it continues to flash rapidly when I hit lock button on remote blue light keep flashing but slower.
Login to reply View 2 answer(s)

12/12/2016

 Dodge Amit Gajjar (690Pts.)

0

2015 Dodge Ram 5.7 Hemi Non PTS installation guide?

Hi Fortin, I am trying to see options for remote start for 2015 Dodge Ram 5.7 Hemi with Key and PTS but when i search site it gives me options for install but no install guides ? Do you have any information on this. Thank you, Brian
Login to reply View 1 answer(s)

09/12/2016

 Dodge Ryan Enfinger (300Pts.)

1

Trying to figure out how to hook up the parking lights only on a 2010 Dodge Ram 2500?

I hooked to the white wire behind the headlight switch with a 1K Ohm resistor like it said but instead all lights come on headlights and parking lights when remote started. Can someone tell me how to hook up just th parking lights while remote started?
Login to reply View 2 answer(s)

09/12/2016

 Dodge Ryan Enfinger (300Pts.)

1

Trying to figure out how to hook up the parking lights only on a 2010 Dodge Ram 2500?

I hooked to the white wire behind the headlight switch with a 1K Ohm resistor like it said but instead all lights come on headlights and parking lights when remote started. Can someone tell me how to hook up just th parking lights while remote started?
Login to reply View 2 answer(s)

05/12/2016

 Dodge Scott Roberts2 (180Pts.)

0

Wont program. No flashing blue light

I can't get my CHRT5 to work. I connected the 2 yellow ignition wires, and the green/red to purple for the MUX. Apparently this is all I need to do. Others on a Ram forum did this and got it to work. I'm thinking it might have to do with the programming with the module. The guy I bought it off of updated it for me, and turned on the 3x lock function. When I hold down the button and plug the data cable, I leave it on the blue light. I then plug everything in. Turn the key to on, and the blue light turns off. Then my dash lights flicker, and I get a check gauges light. Please help.
Login to reply View 1 answer(s)

05/12/2016

 Dodge Scott Roberts2 (180Pts.)

0

Wont program. No flashing blue light

I can't get my CHRT5 to work. I connected the 2 yellow ignition wires, and the green/red to purple for the MUX. Apparently this is all I need to do. Others on a Ram forum did this and got it to work. I'm thinking it might have to do with the programming with the module. The guy I bought it off of updated it for me, and turned on the 3x lock function. When I hold down the button and plug the data cable, I leave it on the blue light. I then plug everything in. Turn the key to on, and the blue light turns off. Then my dash lights flicker, and I get a check gauges light. Please help.
Login to reply View 1 answer(s)

01/12/2016

 Dodge Jimmy Costa (130Pts.)

0

Hello im looking for the install giude for a 2016 dodge ram 2500 diesel

I'm guessing the evoall
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue