Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

12/10/2021

 Acura Yuvrajh Singh (210Pts.)

0

Evo one does not enter program mode to program telematics unit.

2020 rdx push to start. Nothing happens after holding the button for 5 sec with ignition on.
Login to reply View 1 answer(s)

16/05/2021

 Acura Luis Sanchez2 (950Pts.)

0

RFK942 not working after disconnecting and reconnecting the car battery

After getting the RFK942 working I did some maintenance on the car. I disconnected the battery to perform the maintenance required and after reconnecting the battery I attempted to lock the doors with the RFK942 remote. The remote sent the signal but doors did not lock (LED turned red). I thought that perhaps the antenna needed to be reprogrammed so I attempted to perform the programming procedure again. The antenna would not program (no blue LED) so I connected it to the Flashlink Manager to see if something had been turned off. The Flashlink Manager did not recognized that the antenna was connected. From this I am gathering that the antenna was damaged when I reconnected the car battery. Is this possible? If so, what can I do to prevent this from happening again? Would a different RF kit work better (for example the RF642W)?
Login to reply View 1 answer(s)

06/04/2021

 Acura Luis Sanchez2 (950Pts.)

0

EVO ONE does not see RFK942

Good day to you. I am having problems programming the RFK942 to the EVO ONE (installed in my 2010 Acura TL with Push-to-Start). When I connected the antenna to the module (using only the antenna cable the RF kit came with) the blue LED on the RF antenna never turned on. After several attempts, I decided to remove the EVO ONE and connect it to my computer (running Windows 10) using the Flashlink Updater (running the latest firmware). The Flashlink Updater could not detect the EVO ONE (and the EVO ONE LEDs never illuminated). I thought that perhaps the Flashlink Updater was inoperative but when I connected an EVO ALL and two RFK942s to the Updater, I discovered that the Updater is functioning properly. I just programmed the EVO ONE a week ago and had no issues then. In fact, the module remote starts the vehicle (Lock 3x on OEM key fob). Any help would be greatly appreciated.
Login to reply View 1 answer(s)

28/03/2021

 Acura Luis Sanchez2 (950Pts.)

0

Check Keyless Message

The installation and programming of the EVO ONE on the 2010 Acura TL (Push to Start) went well. I am able to start the vehicle, and, as expected, the engine shuts off when the door is opened (which is a bummer). My question concerns a message on the instrument panel. When I remote start the vehicle the "Check Keyless Starting System" (with an amber key with an exclamation point) is displayed. Is this normal? My second question iis about adding an RF kit. Will the RFK942 RF kit work with the EVO ONE on this car? Thank you in advance for your help.
Login to reply View 1 answer(s)

23/03/2021

 Acura Luis Sanchez2 (950Pts.)

0

2010 Acura TL Push Start Evo One will not program

While installing the EVO One to my 2010 Acura TL (with Push-to-Start) I found that several of the wire colors called out by the installation (REV:20191022, Guide 19411) and the Wire Color guide did not match what the car has (on gray 32 pin connector and blue 36 pin connector).  I proceeded by connecting at the specified locations shown on the diagram.  Once the connections were completed, I attempted to program the module (which was updated and programmed with the Flash Link Updater).  Step 1-4 went OK, however, when I got to step 5 (Do not press the brake pedal.  Press the Push-to- Start button twice to turn on the ignition--  The RED LED will flash rapidly 10x times. -- Key bypass programmed. --The BLUE LED will flash rapidly. --CAN-Bus programmed.), the red LED extinguished and I could not complete the programming.  I tried this several time with the same results.  Your help with this issue will be greatly appreciated.

Login to reply View 1 answer(s)

03/12/2019

 Acura Konrad Kalkucki (210Pts.)

0

Solid red flash on evo all

Hi i have a problem with installation. I bought crimestopper rs00g5 and evo all setuped for my qcura tl 2013 push to start. On the begining everything was fine o was able to start my car from factory pilot later i decide install smartphone module and from now o have a lot problems. I wasn't able to programmed rs for smartphone later guys who sells me he help me program rs now on the evo i have all the time solid red light and I can't do nothing. i tried flash evo but still red light apear. maybe im doing something wrong with flashing and other thing there is flashing limit and i have 5/8 what's gonna hapend when will be 8/8???? please help i checked wires and everything looks good.
Login to reply View 1 answer(s)

09/03/2019

 Acura edgar bonilla (130Pts.)

0

vehicle cranks but no start like if key code was not decode corectly

2016 acura mdx will crank but no start?
Login to reply View 0 answer(s)

20/02/2019

 Acura Mike M (9820Pts.)

0

When is the 2019 acura MDX going to be tested?

Looking for install guide for 2019 acura MDX
Login to reply View 0 answer(s)

27/02/2015

 Acura Mike Monoker (140Pts.)

1

evo one doesnt seem to be putting out voltage when remote starting

I followed all the instructions provided in the service manual and the blue led flashes when I hit the lock button on the factory fob and when I hit lock 3x the red and amber led turn on but none of the lights on the dash come on and the car doesnt crank. Also a side point I noticed that the tech sheets from fortin and the wire color website dont match up all the same wires.
Login to reply View 2 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue