Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

29/12/2022

 Infiniti Steve Nah (210Pts.)

0

RFA2A Cable required with NIST1 THarness EVO-All?

I've just purchased (but not yet received) an EVO-All with NIST1 t-harness kit, along with RFK441 remote, reading the instructions it vaguely mentions an "RFA2A" cable. Is this required to make it compatible? Or does the tharness already have the adapter on it? Thanks!
Login to reply View 1 answer(s)

24/10/2022

 Infiniti hnagashio@gmail.com (130Pts.)

0

EVO-NIST1 - Yellow LED never solid

I bought my EVO-NIST1 from Amazon for my 2009 Infiniti FX35 (push to start and AT). 1) I followed the installation guide and connected the harness: 　- The keyport 　- OBDII 　- Brake switch 2) The white/black wire (A.19) of the harness is connected to the light blue wire of the push start　button    (Parking light wire (A.14) not connected at this time) 3) Insert key to the keyport 4) With the main unit, press and hold the programinng button and connect the 4-PIN datalink harness  (Other harness connectors not connected)   [Result]  I tried for about 3 minutes and blue, yellow, and red LEDs all blink together, not alternately. Disconnect the 4-PIN connector (main harness) and return to Step 4) above and repeat, but yellow LED never solid.   Do I need firmware update my main unit? I see below on my main unit:  Model: EVO-ALL  Date: 12/2021  SN: 001A07 338558  
Login to reply View 1 answer(s)

19/10/2022

 Nissan Dobromir Dimitrov (450Pts.)

0

Fortin EVO-NIST1

Hi, i bought Fortin EVO-NIST1 and my question is : Do i need to buy Flash-Link Updater ( https://fortin.ca/en/products/accessories/flash-link_updater/ ) to flash it

or it is flashed already for Nissan Murano Z51 2009 years(Pushed to Start/stop button equiped).

In discription is writen 

    1 x EVO-ALL control module.[1] [3] 1 x Warning label. [3] 1 x 20 Pin general purpose harness. [4]
    1 x 4 Pin Fortin 2-way data-link harness. [2] 1 x Factory Fit T-Harness with OBD interconnect. [4]
 

LEGEND

[1] A firmware update is required.

    [2] Using the 2-way datalink port with an equipped remote-starter, security-system or RF-KIT greatly simplifies installation.

[3] Updated firmware and installation guides are posted on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.

    [4] Secure Clip Harness.  

 

And if i need it can you send it to Bulgaria ?

 

 

 

Login to reply View 0 answer(s)

13/09/2021

 Nissan Vladimir Jancarek (130Pts.)

0

2013 Nissan Maxima EVO-NIST1 not working at all

I bought the EVO-NIST1 remote starter harness which was supposed to come pre-programmed for my car. I connected the connectors to key slot, brake and OBD II. The LEDs on the Fortin unit just constantly flash. There is no way to do any 'programming' as the black 4pin connector doesn't connect to anything on the other end. Am I doing something wrong? This should have been plug and play. Thank you 2013 Nissan Maxima
Login to reply View 1 answer(s)

01/10/2019

 Infiniti Koo Tran (130Pts.)

0

2012 G37x won't remote start unless factory fob is present in vehicle.

G37 is automatic and push-to-start. I have installed the T-harness and programmed the Evo successfully multiple times. I tried different options with the Flash link updater as well. While monitoring the Evo's LEDs, I can see the blue LED flash with each lock press. After the third press the red LED comes on for a second and the brake lights come on. Red LED flashes a few more times like it's trying to start but to no avail. It repeats this process for 2 or three times I think. If I hit lock x3 while the key fob is in the vehicle, it starts right up. I have double checked all my connections. Considering that it's a T-harness, this shouldn't be an issue.
Login to reply View 1 answer(s)

30/03/2019

 Nissan Eric Laing (390Pts.)

-1

Juke still runs after brake press even without key

1: Everything works fine, but I think I found a glitch. If I remote start my 2016 Juke and leave the key inside after unlocking the doors, pressing the brake flashes the parking lights like it should but it still leaves the car running... WITHOUT THE KEY IN THE VEHICLE!!! 2: If I then try to shut it off by going back in the house and lock-lock-lock it does nothing as it has been placed in 'take over mode' or whatever it's called. I have to physically push the start/stop button to shut it off. THEN it starts back up because I recently pressed lock-lock-lock. First issue scares me the most.
Login to reply View 2 answer(s)

12/01/2019

 Infiniti Virakone Thavorn (130Pts.)

0

2012 g37x sedan auto EVO NIST1 REMOTE START ONCE AND NOT AGAIN

INSTALLED EVO-NIST1 PER INSTALLATION MANUAL. PROGRAMMED AS SHOULD. REMOTE STARTED ONE TIME BY 3X LOCK, SHUT IT OFF BY 3X LOCK. AND WOULD NOT REMOTE START AGAIN. I DO NOT HAVE AN EXTERNAL RF KIT. WHAT AM I DOING WRONG? WHAT DO I HAVE ENABLED THAT SHOULD NOT BE OR VICE VERSA. PTS WITH KEY PORT. THANKS IN ADVANCE
Login to reply View 1 answer(s)

06/01/2019

 Nissan Eric Laing (390Pts.)

0

EVO-ALL NIST1 no start, press brake light on.

I've done SOOOOOOOOO much searching and nothing has helped. 2016 Juke PTS T-harness, everything connected properly (verified voltage and connected PTS wire (black/white A19)). Brake lights come on after my programmed lock-lock-lock, Fortin clicks a few times (relays inside) but car won't start then the red LED blinks 3 times and that's it. The entire time the amber dash 'press brake' icon is displayed. Thinking I have now wasted my money buying this starter that after about a month of trying to install still does not work.
Login to reply View 2 answer(s)

18/12/2018

 Nissan Justin Nail (130Pts.)

0

I've installed my evo-nist1 per install guide #74301 and no start.

3X lock and the evo goest through a cycle, parking lights illuminate, brake lights illuminate, but no start. The more I attempt to research the issue the more diagrams I see with different wiring diagrams. Evo also flashes red three times upon completion of cycle. I have exhausted all options I could come up with on my own to resolve the issue, to no avail. Please help! 2015 Nissan Sentra SV push to start
Login to reply View 1 answer(s)

26/10/2018

 Nissan Ed Pribble (220Pts.)

0

Want to confirm a EVO-ALL that's preloaded with EVO-NIST1 can be flashed with EVO-CHRT4 to work on a 2010 Dodge Charger?

Can a EVO-ALL work for any supported car
Login to reply View 1 answer(s)

16/09/2018

 Nissan Shawn Lewis2 (130Pts.)

0

No Start

EVO-NIST1 with the t harness all connected properly at the key port connector the ODBII connector and the brake pedal connector. EVO loaded with the latest firmware and programmed per the instructions and did get the flashing blue, yellow and red lights. I even added the REVO RF remote but when it comes time to remote start the car nothing. After pressing lock lock lock I see the EVO blue light coming one. Then the EVO does its cycle to red light and I get the brake light confirmations but no start. The dashboard does not even come on and I swapped between RL1 and RL2.
Login to reply View 1 answer(s)

14/04/2018

 Nissan ronaldgora (430Pts.)

0

Which locks should I have on or off on Evo-All?

I am using the D1.1 Lock-Unlock-Lock option on a 2014 Nissan Maxima PTS, OEM key fob. I have turned ON: A1; D2; and D5. Do all these need to be on? I want to avoid unnecessay locking/unlocking. Also, truck does not open from key fob when remote start is on. When I open the truck via request button on trunk the car shut-off, which it's supposed to do. I don't understand why the key fob won't do it while remote started. If the car is off the key fob trunk button works. Thank you.
Login to reply View 1 answer(s)

27/02/2018

 Honda Omar Ismail (280Pts.)

0

Evo-NIST1 on Honda?

Hello, i bought an EVO-NIST1 kit that was pre-programmed for the Nissan with the key port / push to start, and i used it for few months then I decided to sell the car. What do i need to make it work on the Honda Pilot 2013? i know i need the T Harness for sure, but can i program the Evo for the Honda? thanks,
Login to reply View 1 answer(s)

19/02/2018

 Infiniti mohammed almuqbil (190Pts.)

0

Steering lock dose work after work install for qx80 2016

I completed install And programming as given instructions car remotly started with no problem but i got key sign in dash and steering lock does not work steering kept on unlock status ??
Login to reply View 1 answer(s)

06/02/2018

 Nissan Ivan Au (180Pts.)

0

Remote Started But..

I just finished installing and programming the EVO-NIST1 as a standalone on my 2016 Juke Nismo PTS. When I got to STEP 7, I pressed on the brake and red + blue LED lit up. Red LED only stayed on for 2 secs and blue LED remained on. I tried it multiple times and got the same result. As I continue to program, everything works as the guide described. Should that draw any concern?
Login to reply View 1 answer(s)

07/01/2018

 Nissan Christian Torres (130Pts.)

0

Juke 2015 Evo-nist1 programming

In the step 11, I need the Flash link updater 2 for decryption or not 

Login to reply View 1 answer(s)

25/12/2017

 Nissan DERRICK WILLIAMS (130Pts.)

0

How to install park lights on maxima wit fortin evo nist1

Where do you out the park light cable at on 2010 Maxima and which cable do you use
Login to reply View 1 answer(s)

27/08/2017

 Infiniti Ahmed Al Harbi (130Pts.)

0

EVO-NIST1 for fx50

Hi 

is EVO-NIST1 for fx50 09 plug and play no need to cut wire ??

 

because i bought the EVO-NIST1 and i have difficult with pts ??

Login to reply View 1 answer(s)

06/07/2017

 Infiniti Hoang Ngo (130Pts.)

0

Starter only works when key is near car. G37X 2011

Starter does not work unless key is near or on top of roof so that the car recognises key is in car.
Login to reply View 1 answer(s)

04/04/2017

 Nissan Omar Ismail (280Pts.)

1

When does EVO-NIST1 shut off the engine?

I installed EVO-NIST1 kit to my Altima 2010 few days back, car starts fine with 3x lock using oem remote, however, i cannot understand when does it decide to shut the engine off. First few times it started fine and didnt shut off, last two times the following happened: Yesterday i unlocked the doors using the door handle buttons while key is in my pocket, opened back doors to get the kids in, then the engine was shut off. today i remote started, unlocked the driver door using door handle button and got in, key in my hand, put the key inside the door pocket, put gear lever to D, engine shut off. when i've done the installation, i did the following: - spliced push to start brown wire / Evo white/black wire - installed all T harnesses as instructed - programming as instructed - didnt connect any other wire Please Help, thanks
Login to reply View 1 answer(s)

17/03/2017

 Nissan Omar Ismail (280Pts.)

0

What is Fortin EVO-NIST1 Preloaded Module?

I saw the model in the subject online, is this factory preloaded at Fortin? How does it differ from EVO-NIST1?
Login to reply View 1 answer(s)

16/03/2017

 Nissan Omar Ismail (280Pts.)

0

Can i install evo-nist on a Nissan Altima 2010 with steering lock fuse removed?

My Car's steering lock failed on me and i got stranded, i hit it with a hammer and it worked, immediately removed the steering lock fuse so not to face this again. will the evo nist1 package still work for a remote start?
Login to reply View 1 answer(s)

08/02/2017

 Nissan amine harir (210Pts.)

0

EVO All with T-Harness wouldn't remote start on Altima 2012

I purchased the EVO ALL for my Altima 2012, I installed it as instructed, I plugged in all connectors and spliced 2 wires, the first one is the black/white from the EVO to the brown wire at the push button, the second wire is the parking light wire, it's the brown wire from the EVO going to the red/blue wire in the fuse box. I programmed the EVO and all lights appeared as expetced, however, the car doesn't start remotely, i tried it with the key inside and still no luck, whenever i push the remote lock key i see a blue light on the EVO. I rechecked all connections and everything seems intact, plase tell me what i'm missing here. Thanks.
Login to reply View 2 answer(s)

25/01/2017

 FAQ amine harir (210Pts.)

0

Remote start does not work on Altima 2012

I'm having a strange issue with my EVO-NIS1 remote starter, I initially installed the kit without connecting the parking light wire, the remote starter worked well for 2 days. I woke up in the morning and the car battery was dead, I jumped the car but the remote starter stopped working, I checked the wiring and everything seemed fine, i reprogrammed the EVO with the flash link and reconnected the wires and did the programming as I did initially. The problem that I faced is not seeing any red or blue lights, It got stuck at the steady yellow (step 4). the car still works fine but without the remote starter which is still installed, the only time the remote start worked is when i was in the car already. I went back to connect the parking light and tried to program it again but i still got stuck at the steady yellow light. I don't know what to do to get passed step 4. Please help. Thanks.
Login to reply View 1 answer(s)

14/01/2017

 Nissan PETER DANNECKER (130Pts.)

0

2016 Rogue Nist 1 Evo All Install ?

I was told go with regular install procdure when purcahsing. On the wiring are we basically only using the bold black lines as wires needed to get the job done? Is the 1 amp diode needed? thanks
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue