Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

11/03/2022

 Infiniti Luis Sanchez2 (950Pts.)

0

RF-ALL ASCL6

I hve a 2008 Infiniti G37 Coupe that has an EVO All with T-Harness. Currently I have the EVO-ALL 642W installed for my RF Kit. I know that I cannot run the RF kit together with the ASCL6. My question is what wire changes (if any) do I have to make to the EVO-ALL harness in order to run ASCL6?
Login to reply View 1 answer(s)

06/07/2017

 Infiniti Hoang Ngo (130Pts.)

0

Starter only works when key is near car. G37X 2011

Starter does not work unless key is near or on top of roof so that the car recognises key is in car.
Login to reply View 1 answer(s)

14/11/2016

 Infiniti Sam Naoum (430Pts.)

0

G37 autolocking on door open

I have had this problem for a while with the EVO ALL enabled. If I open the door it will lock it self while open, with or without the key inside or near the car. Possibly an option I need to turn off? It works fine otherwise, locks after shutdown. I have a toggle switch to turn off the EVO ALL power for when I take the car in for service. When power is removed from the EVO ALL it does not autolock upon door open. I did not even remote start it, but went outside and opened the door and once I openened it the doors locked. I have it setup for Standalone.
Login to reply View 1 answer(s)

26/09/2016

 Infiniti Andrew Mcintyre (130Pts.)

0

2013 g37 install, no start

2013 g37 automatic install, all wheel drive bought the evo-nist1 for infinity with firmware 72 program sucessful, with blue light on programmer when press lock on oem key no remote start after pressing lock x3 car will start with brake pedal and push button any advice? On my 2013 do i have to cut the loop? And how/where is that? Have the flash link, hopeing i wouldnt have to open it, but will if i have to all connections have been recked and tightened - exception : i used a t-tap for the ignition, hesitant to take it off thanks for all the help in advance andrew
Login to reply View 1 answer(s)

20/11/2014

 Infiniti Thorr Giddings (180Pts.)

0

G37 T Harness A4/A5 pin optional?

In guide 12661, rev 20141015, for the THAR-NIS1, on the page 4 wiring diagram it shows both A4 and A5 as optional connections into the BCM. If I just want a standalone remote start with the EVO-ALL, I am assuming I wouldn't need to connect these two wires since these seem like outputs to the lock and unlock and since I am using the factory remote, there would be no point (I am assuming you only connect these two if you are using some other remote so that it can tell the BCM to unlock the doors), correct? So reading the diagram, for a standalone remote start for the G37 with keyport, I only need to connect the Door Pin to A15, the Push To Start wire to A19 and the Parking lights to the brown wire in the harness and then plug in all the other T connectors, correct?
Login to reply View 1 answer(s)

29/10/2014

 Infiniti Devin Hope (110Pts.)

0

2012 G37 starting after 2x lock

Just had your unit installed on my Infiniti G37 and 3xlock on the factory remote works great. 2 days later the installer added a Compustar range extender and now car starts after 2xlock. According to the installer there was a recent Fortin firmware update...could this be causing the 2xstart? It is too easy to accidentally start your car this way. Is there any work around? Thanks!

Login to reply View 1 answer(s)

24/02/2014

 Infiniti Grease Monkey Tuners (1230Pts.)

1

2008 G37 Wont Start on 3x Lock on Standalone Configuration

I have tried 2 different EVO ALL modules and re checked all my (soldered) wiring. Vehicle won't remote start upon pressing 3x Lock but it will start when the external input (yellow/black wire) is momentarily grounded. Did I miss anything?
Login to reply View 1 answer(s)

31/01/2014

 Infiniti Bruce Thompson2 (140Pts.)

1

What is price and availabilty of THAR-NIS1 for 2007+ Nissan and Infiniti PTS vehicles

What is price and availabilty of THAR-NIS1 for 2007+ Nissan and Infiniti PTS vehicles and will this fit a 2013 G37 Coupe Thanks
Login to reply View 1 answer(s)

09/12/2013

 Infiniti Sam Naoum (430Pts.)

0

G37 locks when pressing trunk button

2011 G37 with EVO all as stand alone I am noticing that pressing the trunk button it will lock the car. Cannot remember but this maybe happening when the car is under remote start command.
Login to reply View 1 answer(s)

22/11/2013

 Infiniti Sam Naoum (430Pts.)

1

Lock doors after shutdown EVO ALL stand alone remote start

How do I get the EVO ALL to lock/arm my G37 after shutdown (timed out or turned off)? Can the EVO all when set to remote start trigger the rear defrost?
Login to reply View 1 answer(s)

05/11/2013

 Infiniti Sam Naoum (430Pts.)

2

2011 G37 sedan automatic

I will be buying the Stand Alone EVO ALL system. I do not need anything else, no remote starter or anything? Just wire up the Stand Alone EVO all and it should be all set?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue