Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

03/02/2023

Jeep Nev (130Pts.)

0

Jeep has power but does not crank?

I have programmed the unit sn: 001A07 415854 Evo All. Installed with wiring harness THAR-CHR4 (Both Yellow wires on the harness are connected together). Programmed the unit. All these went according to the documentation, correct leds and all.

My vehicle is a 2011 Jeep Grand Cherokee 3.0CRD Limited with Start Button

I do the 3x Lock Blue Led comes on every time I press the lock button. Then all power comes on, a few seconds later the red and yellow led is solid and the radio shuts off just like it does while it cranks but no crank??

What could I be doing wrong?

Many Thanks!!

0

2012 g37x sedan auto EVO NIST1 REMOTE START ONCE AND NOT AGAIN

INSTALLED EVO-NIST1 PER INSTALLATION MANUAL. PROGRAMMED AS SHOULD. REMOTE STARTED ONE TIME BY 3X LOCK, SHUT IT OFF BY 3X LOCK. AND WOULD NOT REMOTE START AGAIN. I DO NOT HAVE AN EXTERNAL RF KIT. WHAT AM I DOING WRONG? WHAT DO I HAVE ENABLED THAT SHOULD NOT BE OR VICE VERSA. PTS WITH KEY PORT. THANKS IN ADVANCE

0

I've installed my evo-nist1 per install guide #74301 and no start.

3X lock and the evo goest through a cycle, parking lights illuminate, brake lights illuminate, but no start. The more I attempt to research the issue the more diagrams I see with different wiring diagrams. Evo also flashes red three times upon completion of cycle. I have exhausted all options I could come up with on my own to resolve the issue, to no avail. Please help! 2015 Nissan Sentra SV push to start

0

Installed but nothing happened no alarm and remote start works

I did the install as recommend for 2008 Toyota Corolla don't key, ( connection 1 , program 1) manage to program the evo one I used the OEM controls and nothing happened, no alarm working remote start not working either

0

2014 Ford Edge (key start) Evo-All no remote start but does program

Installing the Evo-All (Service #001A06 770324) w/ t-harness in a 2014 Ford Edge with in dash key start. I have made all the connections and rechecked the can bus high and low connections. I made sure with a multi-meter through the OBD2 connector to the connector on the Evo-All that they have connection. I have programed the unit, everything has gone as planned. When I push the lock button the blue light flashes on the Evo-All and the horn honks on the second and third button push but the car does not start. The ignition does not come on. After contacting Fortin they had me connect the dark blue wire (A8) from the 20 pin connector to ground and the red light did not come on. Then I connected the yellow/black(A13) to ground and the car does not start. I first contacted My Push Cart with my issues, the first Evo-All was programmed wrong so that I had to order another unit. I installed the second unit with the same results. I contacted My Push Cart again and they walked me through the programming of the unit and still had the same result, after pushing the lock button 3x (blue light flashes with each lock button press) nothing happens, no ignition, no start. What can I do next to get this unit working?

0

fortin evo chrt5 can i use aftermarket key fob

can i use an aftermarket key fob for the fortin evo chrt5-- my oem key is NOT a keyless entry, my jeep has an after,market kit

0

2014 wrangler with aftermarket keyless entry- use those remotes?

I have the electric life 95338 (https://www.electric-life.com/product/95338-4-door-power-door-lock-kit-w-keyless-entry ) since my jeep came with manual locks.. will the Fortin Evo chrt5 work with those remotes? I do not have a factory keyfob

0

2014 Wrangler Does Everything But Start

I believe I have done everything correct but when I try to start the blue light flashes each of the 3 times I hit the lock button but the jeep doesn't start . What am I missing ?

0

Jeep Commander not starting.

I was able to program the device, when i go to start the vehicle doing 3x lock button, it makes a sound but it will not crank. Just makes a noise like when the key is in the on position. Noticed diagram says to add a hood pin. Will this prevent the device from working? I am using a standalone config. Thanks, any help is greatly appreciated.

1

EVO-CHR.T5 not starting 2015 Jeep Compass

EVO-CHR.T5 with the harness, wired up per diagram C for my 2015 Jeep Compass. Unit packaging included a notice that it had been configured for standalone remote start, with D1, C1, D2, F2, and H3 enabled. Connectors plugged into unit are the red connector, the 5 pin connector from harness with the 2 grey wires, the 4 pin datalink plug is the one that has a red and black wire connected to harness, the blue and white go nowhere. yellow and purple wires go to the 20 pin connector, yellow and green/red respectively. 3X lock does not start the car, and no lights on the unit light up.

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue