Your Cart

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

Clear All

Clear All

Search

Categories

FAQ (407)

Acura (86)

Audi (232)

BMW (44)

Buick (59)

Cadillac (29)

Chevrolet (654)

Chrysler (161)

Citroen (1)

Dodge (562)

Eagle (2)

Fiat (17)

Ford (1318)

GMC (182)

Geo (1)

Honda (590)

Hummer (15)

Hyundai (334)

Infiniti (241)

Isuzu (2)

Jaguar (1)

Jeep (448)

Kia (322)

Land Rover (3)

Lexus (174)

Lincoln (37)

Mazda (471)

Mercedes-Benz (13)

Mercury (12)

Mini (14)

Mitsubishi (138)

Nissan (738)

Oldsmobile (2)

Peugeot (1)

Pontiac (32)

Porsche (4)

Ram (286)

Saab (3)

Saturn (10)

Scion (33)

Skoda (7)

Smart (2)

Subaru (308)

Suzuki (18)

Toyota (1340)

Volkswagen (345)

Volvo (31)

Other (308)

Tags

Looking of our top participants?

See users

Couldn’t find what you were looking for?

Ask us a question

29/12/2022

Infiniti Steve Nah (210Pts.)

0

RFA2A Cable required with NIST1 THarness EVO-All?

I've just purchased (but not yet received) an EVO-All with NIST1 t-harness kit, along with RFK441 remote, reading the instructions it vaguely mentions an "RFA2A" cable. Is this required to make it compatible? Or does the tharness already have the adapter on it? Thanks!

Login to reply View 1 answer(s)

24/10/2022

Infiniti hnagashio@gmail.com (130Pts.)

0

EVO-NIST1 - Yellow LED never solid

I bought my EVO-NIST1 from Amazon for my 2009 Infiniti FX35 (push to start and AT). 1) I followed the installation guide and connected the harness: 　- The keyport 　- OBDII 　- Brake switch 2) The white/black wire (A.19) of the harness is connected to the light blue wire of the push start　button (Parking light wire (A.14) not connected at this time) 3) Insert key to the keyport 4) With the main unit, press and hold the programinng button and connect the 4-PIN datalink harness (Other harness connectors not connected) [Result] I tried for about 3 minutes and blue, yellow, and red LEDs all blink together, not alternately. Disconnect the 4-PIN connector (main harness) and return to Step 4) above and repeat, but yellow LED never solid. Do I need firmware update my main unit? I see below on my main unit: Model: EVO-ALL Date: 12/2021 SN: 001A07 338558

Login to reply View 1 answer(s)

01/10/2019

Infiniti Koo Tran (130Pts.)

0

2012 G37x won't remote start unless factory fob is present in vehicle.

G37 is automatic and push-to-start. I have installed the T-harness and programmed the Evo successfully multiple times. I tried different options with the Flash link updater as well. While monitoring the Evo's LEDs, I can see the blue LED flash with each lock press. After the third press the red LED comes on for a second and the brake lights come on. Red LED flashes a few more times like it's trying to start but to no avail. It repeats this process for 2 or three times I think. If I hit lock x3 while the key fob is in the vehicle, it starts right up. I have double checked all my connections. Considering that it's a T-harness, this shouldn't be an issue.

3x-lock-start-t-harness

flash-link-updater

Login to reply View 1 answer(s)

12/01/2019

Infiniti Virakone Thavorn (130Pts.)

0

2012 g37x sedan auto EVO NIST1 REMOTE START ONCE AND NOT AGAIN

INSTALLED EVO-NIST1 PER INSTALLATION MANUAL. PROGRAMMED AS SHOULD. REMOTE STARTED ONE TIME BY 3X LOCK, SHUT IT OFF BY 3X LOCK. AND WOULD NOT REMOTE START AGAIN. I DO NOT HAVE AN EXTERNAL RF KIT. WHAT AM I DOING WRONG? WHAT DO I HAVE ENABLED THAT SHOULD NOT BE OR VICE VERSA. PTS WITH KEY PORT. THANKS IN ADVANCE

3x-lock-no-start

Login to reply View 1 answer(s)

29/12/2016

Infiniti MARVIN REDMOND (130Pts.)

0

Qx56 Install

Im trying to do this nist-1 install on my 2011 QX56 , Has anyone done this vehicle before? I was wondering should I install the b/w wire to to bcm behind the cluster , or is there a wire on the push to start harness that I can tie into. If so what color is it on the pts? Fortin says it a light blue wire on pts but i didnt see it!

Login to reply View 2 answer(s)

19/02/2018

Infiniti mohammed almuqbil (190Pts.)

0

Steering lock dose work after work install for qx80 2016

I completed install And programming as given instructions car remotly started with no problem but i got key sign in dash and steering lock does not work steering kept on unlock status ??

Login to reply View 1 answer(s)

27/08/2017

Infiniti Ahmed Al Harbi (130Pts.)

0

EVO-NIST1 for fx50

Hi

is EVO-NIST1 for fx50 09 plug and play no need to cut wire ??

because i bought the EVO-NIST1 and i have difficult with pts ??

Login to reply View 1 answer(s)

06/07/2017

Infiniti Hoang Ngo (130Pts.)

0

Starter only works when key is near car. G37X 2011

Starter does not work unless key is near or on top of roof so that the car recognises key is in car.

Login to reply View 1 answer(s)

29/12/2016

Infiniti MARVIN REDMOND (130Pts.)

0

Qx56 Install

Im trying to do this nist-1 install on my 2011 QX56 , Has anyone done this vehicle before? I was wondering should I install the b/w wire to to bcm behind the cluster , or is there a wire on the push to start harness that I can tie into. If so what color is it on the pts? Fortin says it a light blue wire on pts but i didnt see it!

Login to reply View 2 answer(s)

19/12/2016

Infiniti Billy Bob (130Pts.)

0

2008 g35x no longer needs OEM keyfob?

I just installed the EVO-NIST1 standalone with the Fortin RF642W RF Kit on a 2008 Infiniti G35x according to Guide 24031 and have a couple comments & questions after playing around with it:

1) LOCK x3 works with the OEM fob, however it cannot remote stop the car with LOCK x3 again. This is known, so it is not a problem.

2) After remote starting the car and unlocking it (either with door button or with either of the fobs), I can open the door, step on the brake, and I am able drive away. That works as intended, but the problem is I can drive away without having the OEM key fob around. The instrument cluster screen does not say NO KEY like it normally would if the key has left the car. In other words, one would be able to drive off without having any remote on them as long as the car gets remote started followed by an UNLOCK signal. Are remote starts intended to bypass the need to have the OEM Intelligent keyfob for the take-over?

3) While the engine is off, the LOCK signal from either the RF fob or OEM fob will lock the doors and prompt the RF antenna's LED to start flashing (blue) and will not stop unless I press the UNLOCK botton on either remote. What is this flashing for? Can this be disabled? I do not need or want any alarms or extra security features. I am more concerned about it draining the car battery. Please advise.

4) After remote starting, the first press of UNLOCK with the RF fob ONLY turns off the Antenna's flashing. I have to press unlock a second time to unlock the car, however it would unlock all four doors at once. I had configured it through Flash Link (B1 on) to unlock driver door on first press, and lock all on second press but that isn't the case. What exactly happens on the first UNLOCK that stops the antenna's LED flashes? Can I get the unlock button to unlock the doors on first press?

5) How does IDLE mode pertain to push-to-starts where the key does not need to be in the ignition? I'm guessing it is not needed but just want to be sure.

6) I had to use the RL2 connector to get remote starter to work, although the guide says RL1 for G35. This might be the issue with folks who cannot get their '07 - '08's to remote start.

Login to reply View 1 answer(s)

14/02/2016

Infiniti Ahmad Doleh (150Pts.)

0

can you check if my Fortin is flashed

Can you check if my Fortin is flashed? I went to the shop today and they insttalled the fortin but the only thing turn just the ignition. do you have any idea about that?

Login to reply View 1 answer(s)

17/09/2015

Infiniti Duane Heaven (220Pts.)

1

Car Starting

After remote starting and entering the vehicle, my car sometimes turn off and turns on by itself. How can I fix this? 2012 Infiniti M37x EVO-ALL with T-HAR

Login to reply View 1 answer(s)

11/02/2015

Infiniti Adam Clark (160Pts.)

0

PTS wire white/black

In the above answer it says the pts white black wire needs to be connected. I am using the t harness that has me unplug the pts switch and then put it in series with the T harness. Shouldn't that take care of the termination? Or do I still have to terminate? Thanks!!

Login to reply View 2 answer(s)

11/02/2015

Infiniti Adam Clark (160Pts.)

0

PTS wire white/black

In the above answer it says the pts white black wire needs to be connected. I am using the t harness that has me unplug the pts switch and then put it in series with the T harness. Shouldn't that take care of the termination? Or do I still have to terminate? Thanks!!

Login to reply View 2 answer(s)

13/01/2015

Infiniti Jonathan Arseneau (220Pts.)

1

Radio Not Working after remote start

Nope, that doesn't make any sense to me. I don't really understand how to let it learn, and what it means here. I know what you mean, by settings everything up, like a default settings, so when I remote start, everything would be running at I last started. But, I don't have an option in my car to disable the radio, that doesn't exist. There is no way to screwed the functionnality of the radio manually. Only thing that screw it up, is the remote start. What I understand from you, is that the CAN-BUS is not related, cause all it does, is the same sequence as someone sitting in the car. So, why is there a CAN-BUS connector on the unit then, I can remove this then... Could you please explain the let it learn the settings while the EVO has the car started? Cause the radio not working, is not a settings I can set.

Login to reply View 2 answer(s)

13/01/2015

Infiniti Jonathan Arseneau (220Pts.)

1

Radio Not Working after remote start

Nope, that doesn't make any sense to me. I don't really understand how to let it learn, and what it means here. I know what you mean, by settings everything up, like a default settings, so when I remote start, everything would be running at I last started. But, I don't have an option in my car to disable the radio, that doesn't exist. There is no way to screwed the functionnality of the radio manually. Only thing that screw it up, is the remote start. What I understand from you, is that the CAN-BUS is not related, cause all it does, is the same sequence as someone sitting in the car. So, why is there a CAN-BUS connector on the unit then, I can remove this then... Could you please explain the let it learn the settings while the EVO has the car started? Cause the radio not working, is not a settings I can set.

Login to reply View 2 answer(s)

11/01/2015

Infiniti Jonathan Arseneau (220Pts.)

0

2009 Infiniti FX50S - No sounds from Radio after remote start

When I use the remote start function, the car starts fine, but half of the time, the sound from the radio is not working. Sound from bluetooth, from DVD is working fine, but not from radio. Only does that with remote start.

Login to reply View 1 answer(s)