Questions & Réponses

Tried installing an EVO ONE module in my 1993 Dodge Dakota. Manual Transmission. Got all necessary wires connected, module will power on, and allow me to program one remote. Afterwards, it will not respond to anything. The antenna LED will not come on, the module lights would alternate red, yellow, blue. Got the flashlink, updated the module, same thing. At a loss, any help appreciated...

Starter kill relay wiring for a 2015 dodge Durango with a fortin evo one with thar-chry7 t-harness

EVO-ONE. Device Flash Limit Reached. (Remote Start Not Working and other issues). EVO-ONE S/N: 002B07 337434 (Starter Vr. 7.1.21), (EVO-ALL Vr. 2.4.18), Date: 02/2019. Car Mazda CX-5 2014 PTS A/T - EVO-ONE + THAR-ONE-MAZ3. Two OEM Remotes. Car OEM alarm system with its hood switch. Hello, when I try to change or update firmware to the EVO-ONE on Remote Start panel the FlashLink Manager says: Device Flash Limit Reached. Could you please reset my EVO-ONE completely as it was when I got it in 2019?, so I could config and install it again. Looking forward to your reply. Thank you. Anyway, this is what happened to me if it is in your interest to know: Module EVO-ONE installed by myself following Fortin guides and working since March 2019 till few weeks ago. The module went working fine for several years till the day when it didn't start the engine, despite all the sequences on the module and on the car were ok as usual. First I tried to reconfig some controls on the module through FlashLink Manager, very few of them because I do not know what exactly they do and I do not want to damage both the car and the module. No Valet mode. No luck. So I decided to reinstall / update the module with the latest Firmware versions, both ByP (85.14v) and R/S (1.26v). With no luck. Then I noticed something new on the car panel, it randomly started to show (only one of them at every attempt to start the car) the following alerts: "Key not found" (despite being into the car), "Brake-Pedal inspection needed" and "Check system key". Arm / disarm car and parking lights worked and blink ok as usual. That all took me back into having a look at all intallation Fortin guides to this car. I thought those panel alerts were caused (perhaps), because of updating firmwares on the module, so I installed some previous firmwares and tried in the car, no luck. Then I Master Reset the Bypass (https://fortin.ca/en/download/61931/61931.pdf). All leds on the module were blinking ok so it seems to work fine. OEM remotes work (open / close the car), and also I can change and save config options on the pc through FlashLink Manager. Still stuck in the same issue though, it didn´t start the engine and those alerts on the car panel persist (randomly). Then I also tried to reset the Remote Starter (https://fortin.ca/en/download/61941/61941.pdf), no luck even to get it reset. (Is there any other way to reset the R/S I am missing?). After some Remote Starter firmware updates were installed into the module and tested in the car, something new happened in the car panel: it turned crazy with all the lights and icons on the panel randomly flashing. I stoped this flashing just pussing twice PST button. Arm / disarm car and parking lights were Not working as they should be. This flashing crazy lights on the panel disapeared once I removed the module and the harness form the car. Icons panel got back to normality. Every time connecting and disconnecting module from the car, car battery (-) was disconnected. Finally, and after another R/S firmware update on the module, it looks like the module has been blocked because the three leds (blue, yellow and red), blink at the same time for 25 times. Module does this kind fo blink every time I connect either to the Flashlink Manager on the pc (when selecting Remote Starter config panel), and to the car harness. At this point, when the module is connected to the car there is no light (response) on the blue led when I press any button of the OEM remote (despite they open/close the car). I can start/stop the car with PST (yellow led on the module lights). And now when I try to change or update firmware to the Remote Starter the FlashLink Manager says: Device Flash Limit Reached. Please any help from you very appreciated. I would like to get the module working back in the car as it was since 2019. Looking forward to your reply. Thank you.

Have a 2014 acura rdx with a push button start. The kit came with a THAR-ONE-HON1 T-Harness. However it seems that it is for key-to-start vehicles. Which T-Harness would work for my vehicle?

I have evo-one installed and both of my remote controls are broken. Can I use the EVO application outside of USA and Canada? I would like to order spare remote control keys as well. Which model you recommend? Thanks in advance.

Привет. Как подключить EVO Q7 TDI 2016 Cтандартний ключ и есть кнопка . Каким руководством рользоватся ? Спасива.

Hello Everone We installed a EVO One Sin# 002B04690023 with 411 RF kit on this 05 Camry with installation guide # 84961 we folowed it to a T the vehicle starts fine but when the factory alarm sets it gose off with it running. Do we forget or need to set something in the evo one to disable or bypass the alarm we can't find any setings for this Please help. Thanks,

Hello, I have been using an Evo One Fortin kit to start my car for the last 3.5 years. I have a 2020 Honda Accord with manual transmission. It just recently started to fail to remote start my car. When I start it manually, it works and doesn't struggle to start. I noticed that all the functions like heated seats, blower fan, rear defroster all work and the engine turns over, but the engine does not start when I attempt to start it remotely. It does this three times before shutting down. It seems like the module is not giving the car the bypass code. I am using the 3X lock function with the OEM fob and not an RF kit with stand alone fob. Any suggestions will be greatly appreciated. Thanks

Installed EVO-ONE car starts with OEM remote, and valet button works. After using the OEM unlock I tried to program 942 and can not ever get a blue LED on antenna blinking or solid, even following the on-off-on instructions. Valet button on antenna does not work. I checked out the antenna cable and it is good. I do NOT get a blue flash of the antenna LED when I plug in the antenna connector. Tried plugging the antenna into the Flashlink programmer and it can not be detected even when "special unit" is checked. Is there anything else I can do to determine if it is a bad antenna or something else ?

Hello, I installed a EVO-ONE stand alone on a 2023 VW Jetta GLI PTS manual transmission. I had to bring the key to my girlfriend this morning because she succeeded (unintentionally) to leave with the car that she had remote started with the OEM key (3x lock). In the past, she once forgot to bring the key, but when she pressed on the brake pedal to release the parking brake, the engine has stopped. But this time the engine kept running, and she had no message stating that the key was not in the vehicle in the cluster. -The module has been programmed with Flashlink manager and a Flashlink 2 on March 27th 2024 with the most recent firmware at this time. -The battery of the sacrified key has been removed, and it has been tied far enough from the transponder antenna located on the steering column. -The module was installed in accordance to the guide #99681. Is there any chance that a firmware reflash could resolve this issue? Thanks!

21' Audi SQ5 - Evo-One with Remote Start and Thar-AUD2 Harness. The windows will not go up or down from the app. The app say Aux5 should put the windows up, and Aux6 should put the windows down. When pressing function Aux5 on the app, it says "Windows Closed", but nothing happens. When pressing function Aux6 on the app, it says "Aux6 Command Sent" and makes a sound of the windows going down, but nothing happens to the car.

While driving, the light on the antenna blink a purple light. Sometimes, the car flashes light and honk at the same time and the light turn green and stop. How so I fix it?

Hello, Does anyone have an actual diargram that shows the connections from the relay to the clutch switch? Or a personal step-by-step you may have used. Before I cut factory wires I would like to be sure. I have both the EVO-All and EVO-One with the CHRT5 and CHRT7. Th

I have a 2004 Dodge Durango with the SKIM removed. The factory key fobs no longer work because of this. I want to Install a remote starter EVO-0ne with the RFK441. With the remote start work, and will the lock and unlock buttons on the RFK441 work?

I was wanting to know how to active my seat heater on start up with my car control app for a 2023 Kia Forte Gt.

When I get in and push my start button, check my tire monitoring system keeps flashing until I hit the brake and then it stops and my car is back to normal.

nissan versa 2008 manual, got the evo-one with 442 remote, all good, Trying to add the LTE module to my assembly, but cant figure the sequence properly,

I successfully finished the install on a 2015 Subaru Legacy 6 speed manual Evo-One with the t-harness and rf kit. Everything went well and works okay, but after the install the red security light in the cluster stays on all the time while running but its very dim. When the car is off its blinking as its supposed to, but when it blinks "off" its still slightly light up when it should be totally off. Seems almost like its getting a constant back feed from somewhere. I'm not sure if this is a wiring mistake or possibly a bad unit?

Hi could you please reset my evo-one serial number 002B04 700870 I have a yellow and red lights flashing when I connect the heavy wages connector. I have tried to resetting with the valet switch but still flashing. Any help will be appreciated. This module is brand new.

Bonjour, Suite à la pose d'un module RM912 sur une Ford Mustang de 2006, Transmission manuelle avec clé standard, impossible de programmer la fonction à distance pour le démarrage Etant un garage j'ai suivi le schéma de cablage fourni sur le site pour mon modéle, Guide 85601, les télècommandes repondent bien, le boitier clignote en permanence en alternance de 3 couleurs. Sur cette mustang, faut il passer par Flash Link pour programmer les fonctions ou un branchement supplémentaire est il nécessaire ? Cordialement.

i installed evo one as instructed by guide 22301 and all wires confirmed to be as on the manual, during programming the key the light dont flash 10 times I uploaded newer version and the recommended version by flashlink and didn't work . additional question, can i start it through oem remote 3X lock or not . thanks

Nissan X trail 2024 software is not on website, so I have 2 quetions 1- is nissan X trail 2024 is the same with rouge 2024 software? 2- is can be available soon? best regards

2020 forester when programming when I start the vehicle it won’t rapidly flash 10 times. Help