Questions & Réponses

“I am writing to report an issue with my car’s remote start and shutdown process. When I press the lock button on the car key three times, the car starts remotely, as expected. However, after entering the car by pressing the unlock button, I encounter a problem: when I press the ‘Press to Start’ button twice in succession and then press the brake, the engine shuts off immediately, and the message ‘Wegfahrsperre’ appears. Could you please help me understand and resolve this issue?”

FORTIN EVO-ONE-MIT2 EVO-ONE + T-KABELBAUM

Mitsubishi Outlander 2016 

Hello, 

When pressing the remote start button on the RFK942 key fob, the remote start does not always activate. When this does not happen, the car behaves differently: the marker lights come on along with the low beam headlights for a couple of seconds, then everything goes off. However, when the remote start command is successful, the low beams do not activate, the turn signals come on for half a second, followed by the marker lights. Additionally, there seems to be a door lock click, then the engine starts, which can be seen in the video. https://youtube.com/shorts/B6o0cWfPQQo

Remote start with the factory key, activated by three presses on the lock button, does not cause any issues with the remote start.

The flash-link 4 has version 5 firmware, vr. 4.08. An additional impact sensor and siren are installed.

There is also an issue where if the car is armed or started with remote start, if the trunk door is opened with a sweeping motion from below (via the sensor), the siren starts making noise. If opened with the button on the door, everything is okay.

Thank you for your help!

Reposting because, well, the first thread will never been seen again and the answer missed important points

Please read the whole thing.

Eclipse Cross, 2018, SE

Latest firmware for starter and bypass. Loaded recommended options and confirmed the options specified in the setup PDF for the car were set. Using the MITS2 harness.

3x lock works for remote start works.

Tried various (3?) methods of syncing, all of which seemed to work, however, device still only shows it's own information (battery voltage, GPS, and "connected" icon)

Yes, using the crossover cable. Yes using the right port on the evo-one (blue).  

Tried sending the unlock command/lock command at the last steps of the sync. Door open and door closed. Didn't seem to matter. 

Tried switching the protocol in the app to something else then back to Fortin.

Confirmed the "datalink" protocol is Fortin 2  

Previously, this carlink was used with an evo-all for a different car and it worked great. Now it does not. 

I installed my Evo One with standard key. well i installed it and it wasn't working 100% meaning that some time it would work on the first try and not work until the second try, or even not at all. So i went back and checked and I may have found a loose starter (yellow) wire, but not 100% certain of that. Now Click the fob 3X, all the lights come on (dash, interior, parking) doors unlock, it seems to run its course. same as before but now does not start at all. Parking lights flash 4X indicating no tach. Then it cycles again with the same results but no start. I think the encryptor is now not working or had some issues to start with. with my power probe I have tested that everything else coming from the evo one is working. The ignition wire (pink) + comes on and then the starter wire (yellow) + comes on but the car will not start. I then tested the cars harness by unhooking the evo, then I put the key in the ignition in the on/run position, then use my power probe on the same wire that the yellow wire was plugged into, the car will start. 

So then I'm thinking I should try and run through the install procedure with plugging in the 6 pin and running through the LED flashing light stop on Blue again procedure. This did not help any.  

So, what is the best way to reset everything and try it again, or do you have something else I should check first,

Best Regards

Louis   

EVO-ONE + EVO-START2 Combo

Standalone

2008 Mitsubishi Lancer

Car starts fine with factory remote. Evo-Start antennae blinks green a couple of times, then amber. 

It saying on my app, Sending, Car Locked. -- Sending, Car Unlocked. Etc. 

Nothing is happening. 

I have un paired and and re pogrammed several times. Nothing has seemed to work. Do I need the RFA2A?

I understand the topic has come up on here, and I have read through most of the answers, its just not happing for me. 

EVO-ONE + EVO-START2 Combo

Standalone

2008 Mitsubishi Lancer

Car starts fine with factory remote. Evo-Start antennae blinks green a couple of times, then amber. 

It saying on my app, Sending, Car Locked. -- Sending, Car Unlocked. Etc. 

Nothing is happening. 

I have un paired and and re pogrammed several times. Nothing has seemed to work. Do I need the RFA2A?

I understand the topic has come up on here, and I have read through most of the answers, its just not happing for me.