Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

EVO-One starts then shuts off after 2 seconds

2017 Promaster gas standard key. After remote starting successfully, vehicle shuts off after 2 to 3 seconds. If it matters, the parking lights flash four times after it shuts down. Engine supervision selection is the recommended Tach Data-Link only selection. I've tried all other tachless, etc. settings in section 20 and none of them even start the vehicle. Remote start is lock/unlock/lock if that matters.

0

Is evo-one compatible with gasoline 2023 Ram 2500?

Install instructions only list diesel pushbutton start.

0

2014 ram 3500 will not remote start. Manual transmission

I followed the instructions for the thar-chr7 what else am I missing? flash link does not have an option for manual transmission I did not cut the yellow wire

0

cant get a steady blue light on evo one ram promaster

evo one ram promaster 2020 no solid blue light. checked all wires for connectios they are good. Looking at the wire color info and it shows that there is a second 12+(2) connection but the install guide ony show to 2017. Are there two 12+ connections or not.

0

cant get a steady blue light on evo one ram promaster

evo one ram promaster 2020 no solid blue light. checked all wires for connectios they are good. Looking at the wire color info and it shows that there is a second 12+(2) connection but the install guide ony show to 2017. Are there two 12+ connections or not.

0

'19 Ram promaster

Hello, I am looking to get remote start only for my '19 Ram 1500 promaster. It does not have remote start or alarm now. It uses a standard turn key. According to the website it says I can use the EVO-ONE. Looking at the install instructions on page 5, it shows what looks to be a remote starter module of some sort?

Am I looking at the right instructions for this setup?

If so, do I need another part?

 

Also, is there a t-harness made for this yet?

 

Thanks!

1

Promaster Horn

I have an EVO-One installed and just installed the RFK912. 2018 Ram Promaster 1500 Gas. Two things: 1. Honk on remote start (after lock unlock lock) horn beeps then starts. I want to eliminate the horn beep! It will wake the dead it's so loud, I wish it would just chirp. I think I have everything I can find turned off or to lowest setting but nothing's changed 2. Horn confirmation on unlock? I'm used to a horn chirp on cars when locking but the RFK912 makes no confirmation chirp on lock, but it does on unlocking. I want this to be reverse and a chirp honk rather than blaring horn (see above) I don't really want to disable the horn altogether so wanted to check to see if I'm missing something in the module setups

0

Does EVO-ONE need a clutch wire for 2014 Ram 3500 diesel manual transmission?

After researching my options for a manual transmission I've determined the EVO-ONE coupled with the THAR-CHR6 was the best configuration for a stand alone system retaining original smart tip key. (Please correct if there is another option) According to another Q&A discussion regarding a RAM 3500 manual diesel, it was mentioned by Antoine Marion that a "clutch switch wire" has to be connected. After referring to Guide # 98581 for the EVO-ONE I did not find any information regarding the clutch switch. Shouldn't this be handled through CAN bus or does it need the clutch wire bonded with an output on the EVO-ONE?

1

Key take over has suddenly stopped working?

I've had fortin remote start for about 8 months, while I was driving it suddenly the dash went flashing. And I stoped turn off the truck and started it again normally. Then when I went to try to remote start it everything worked until the key take over. When i pressed on the brake its just shuts off now. Normally what I do is remote start x3Lock, then unlock and close door, insert key and turn to run position, and then wait 5 seconds and then press brake pedal and shift and go. But it has suddenly stopped working. Has anyone else had a similar situation. The parking lights come on, I have all the recommended settings for my truck. I have updated it to its recomended. 2016 ram 1500 ecodisel. tip key

0

2016 ram 3500 manuel evo-one 8 seconde cranking ne fonctionne pas

j'ai tenté a plusieur reprisede configurer , le evo-one pour qu'il crank plus longtemps , parlé deja a une personne au telephone me disant de selectionner le mode 20.5 8 second cranking , mais selectionner ou pas , le crank est d'environ 2 seconde et arrete , parfois 1 sur 5 le moteur parvient a demarrer, comment je fais pour pouvoir avoir au moin 5 seconde de cranking , tout le cablage est ok , le ready go est ok juste la programmation qui bug , comme si meme je change les parametre ca fait rien quoi faire ?

0

evo one module won't power up

Hi.. i'm trying to use compustar rf kit to evo one and i modified the antenna wire of compustar according to evo protocol but i plug in to evo one antenna port and i realized that is should use the datalink port instead compustar antenna is not responding so i tried plug the evo one to flashlink if i can change the rf setting but the module won't get any light that power indicating. is there any posible to reset the evo one?

0

2015 Ram starting but not staying running

2015 Ram starts For about 2 seconds and shuts right down and then tries to restart and then shuts down again. Somebody please help. I have tried reprogramming and nothing. I have 12 volts at the ignition wire. Please help.

0

Truck shuts off after pressing push start button

When using the remote start the truck turns over fine, but when pressing the push-start button nothing happens and as soon as I touch the breaks to change gears it shuts off.

0

Truck shuts off after pressing push start button

When using the remote start the truck turns over fine, but when pressing the push-start button nothing happens and as soon as I touch the breaks to change gears it shuts off.

0

2014 RAM1500 ecodiesel PTS engen ligt on after remote start

On last firmware my EVO-ONE + Drone Mobile when I start from drone it will kik on engen light. Was offered by support to downgrade to 74.22 firmware, after downgrade it will only flush 4 times parking light, that all. All wiring soldered and checked. Any solutions? Thanks

0

EVO-One starts then shuts off after 2 seconds

2017 Promaster gas standard key. After remote starting successfully, vehicle shuts off after 2 to 3 seconds. If it matters, the parking lights flash four times after it shuts down. Engine supervision selection is the recommended Tach Data-Link only selection. I've tried all other tachless, etc. settings in section 20 and none of them even start the vehicle. Remote start is lock/unlock/lock if that matters.

0

Programming Step 4, Blue LED will not turn off when ignition to run

2014-2017 Promaster, regular key. When programming hangs up at step 4, blue light stays solid does not turn off when ignition turned to run. Some of the other troubleshooting mentions ensuring that the yellow wire, A1, has power when the ignition is on. But, in this install guide, yellow wire A1 is not used.

0

Programing light is blue, then off, but then wont flash

2018 Dodge Promaster Standard isntall - Blue LED comes on, plug in all connectors turn to on, LED doesn't flash, just remains off. HELP. EVO-ONE

06/05/2018

Ram wizzled (130Pts.)

0

not programming?

I'm trying to program my EVO-ALL for my 2016 Dodge Ram with the tip start key. After pressing the programming 4x and the light turns to solid yellow it says "insert key" and the light should turn to red.  I insert the key and nothing happens.  I've flashed the module to 74.37 and still nothing.  I have master reset it and also programmed the can-bus  and the blue light stays solid on canbis programming. Any ideas?

0

Evo-CHRT4 vs Evo-All vs Evo-One

Once installed what is the difference between the Chrt4, ALL, or ONE - besides thE CHRT4 has a T harness?

 I have a 2012 Ram 2500 Diesel Automatic with the remote start module installed already so I just need the module and harness minimum. I will program it to have glow plug/heater delay and crimestopper REVO enabled with the flasher2. Is there a fee for the crimestopper enableing?

I'd like to add a crimestopper 2way system if my range is bad, but hoping the oem fob will work. There is no way to tell with my cement walls vs the window or not until it's installed. If I have to do 2way I was hoping that it would be able to do both - Have a 2 way at home and carry my oem fob in my pocket for starts when walking out to the truck, or from my office close by. I have a Ram fob Saab fob and don't have room in my pocket for a third fob.

I see the CHRT4 and ALL uses the oem keyfob which I like, can it do 2 way also at the same time  as the 3x lock oem fob? 

I don't understand stand alone starter vs not - I'm assuming that means the CHRT4 can be used with a 2 way? however... Under optional technology section: The One shows it can have RF (2way) remotes but says it can't do stand alone

What modules can be hooked up to the Evo-One

What external triggers can be hooked up to the CHRT4, can modules be hooked up to the CHRT4 or ALL?

In the bottom check mark section the CHRT4 has NA for remote start so does that mean it can't do 2way, this contradicts the Stand Alone option above? 

 

I see no difference between the CHRT4 and the ALL if I get the THAR-CHR4 T harness. In fact based on contradictory information on the compare screen I see no difference at all between all three models, except price since my truck has the remote start function setup but just needs the module/controller.  They all say the will monitor for 3x lock and will start or stop the vehicle. Can you please ellaborate on the differences in detail, including options, modules, triggers, systems, etc that can be added. I'd like to see the whole picture and know which is more future proof/upgradeable as well.

Thanks for your time,

James

 

 

The module will monitor the OEM remote for 3X Lock and will start or stop

 

0

Installation Setup

I've searched all over the site for these questions but can't seem to find them. I'm in the process of ordering the Evo One for a 2013 RAM 1500 with tip start. No factory alarm. I like the feature of your product having a built in alarm. My question is what else will I need to wire this up? Will it work as the truck's horn as the alarm? Will I have to splice anything? I'd hate to cut any wires which is why I liked your product. But if I have to I will. I just want to be prepared ahead of time. I will also be purchasing Text2Car but I see the wiring setup for that already. Any other configurations that i'd need to do to the Evo to set that up? Forgot to add, is there any idicator light I can add to the vehicle to show the alarm is armed so it's visible to anyone looking in? I know other alarms have that option. If I can wire one up for this it'd be a nice addition. Thank you.

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer