Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

2010 ford escape KEY-OVERRIDE-ALL

I'm installling the KEY-OVERRIDE-ALL with a DEI remote start. When I attempted to program prior, I would see the LED start flashing, but programming didn't complete. Now when I attempt to program, the LED on the module stays on and the security light on the dash flashes rapidly. I've confirmed I have 12V on Red, Ground on Black, Ignition on Yellow, and remote start staus on Blue. Is there anything else i should try on this module? The module was purchased new in December and hasn't been installed in another vehicle.

0

2017 EvoOne with TharFor3 T harness, blue light won't blink on programming

Thank you in advance for any help! I am a long time using of the EVO ALL and have done a few EVO ONE. A bit stumped on my 2017 F150 though. Using EVO ONE with the THAR FOR 3 harness. All plugged in. Following wiring diagram for the A1 and A16 (put them together) on the white 20 pin connector. When I go to program it, I can't get it to "blink blue". Therefore, I can't get any further in the programming procedure. Followed the directions in the Guide. What could I be missing? Joe

29/09/2021

Ford Gdrover (400Pts.)

0

2007 Ford Escape- are both OEM keys required to program EvoRide

Evo Ride-- Are both keys required to program module? 2007 Ford Escape,Standard Key, with Ultra Start Remotre start. Vehicle Remote start works with OEM Key in ingnition in the off position The Evo Ride LED displays correctly up to asking for the second Key and on step 5 when the remote is activated the LED remains solid red and does not flash rapidly 10 times Unfortunatly The second OEM key has been lost and is not available

0

why can't I edit my evo all options

ok 2012 ford foucus issues with Flasher tool even unistalled and reinstalled either wisard or pro mode I can't well It won't let me .says at Flash limit .I pesonally think WTF we bought the device and the Flaser that gives yoiu acces I dont care if its 100x If why I cant is due to Fortin limit locking well someone needs to think that one real fast consumer affairs and I;m positive this isn,t part of the deal upon purchase . had no problem before wirh remote start edit options as I wanted to use the newly evo alarm to enable chirp and enable siren not horn .. and I would like to add one more comment the few times I have called Fortin tech suppport I sure can tell the level of service given to the stupid consumer installers why do I know this well guess a small world I have a friend whom is a pro install and listened in on his coverstion wow A DISCRACE

0

How do you flash the module since it didn't come working?

So, I bought a EVO-NIST3 for my 2015 Nissan Rogue which in the write up said it works for them, but now I'm told the unit has to be Flashed programed before it wi actually work. How does one go about getting it flashed so the unit works?

0

what is flash version 0.99

not finding this verion on web site can not get the red light off

3

Troubleshooting guides based on the FORTIN product you are installing.

Just thought I would post this up maybe some people will find it useful!

Troubleshooting guides based on the FORTIN product you are installing.

 

Here you will find the following:

 

1: Useful information on programming your module to the vehicle.

2: Installation guides for your vehicle.

3: Common issues when the module will not program.

4: Vehicle specific information for your module/installation.

 

Here is the link:

 

http://fortin.ca/en/support/troubleshooting.html

0

Red light Won't flash when the key is inserte during programming

I installing an EVO-ONE standalone setting, i had update the firmware and select the options recommended, but when im trying to program the module it won't program. So i hold the button, then i connect the 20 pin connector then the 5 pin and last the 6 pin connector, then the module start flashing slow blue,yellow,red,blue & red after it gets red and i release the button and the light stays on but when i insert the key, it won't flash the 10x. Its a toyota camry 2009 standard key.

1

2013 Lexus GS450h EVO-ALL - light won’t blink blue when pressing lock 3x

I did everything as instructed , connected the CAN Hi and Lo , connected to green wire on push button . programming was successful, it just doesn't detect anything when I press Lock 3x, no blue light blink.

0

Flash link update to firmware stuck at 1%

Went to update the flash link to the newest firmware version. Update never moved past 1% after an hour and now the flash link says there was an error when doing last update and so it forces you to try again but it never gets past 1%. So now it will not connect to the evo-one to change settings.

0

Why won't my evo all update?

I have EVO ALL hardware version 6 service number 001A06 122506. I can't get this to update or work. I spent good money on this thing and now it's a paper weight. Any ideas? Please and thank you.

0

Why does my evo all module do something different every time I try to program it? Why won't it start vehicle?

Installed with fort-1 t harness. Wiring double checked per troubleshooting guide on website.

0

2018 ram 1500 standard key, blue led not flashing , stays.solid blue.

I follow the steps and everything goes well until the very end when I put the key back in ignition turn to.run. red led.goes out but blue doesn't..blue stays solid and doesn't flash at all. fast or slow like supposed ro

0

Parking light not flashIing when the alarm of the Evo is triggerd.

I have this alarm install for 2 year now just notice today at work when my car alarm was triggerd the parking light was not flashing. Eveything seem to be working fine, the parking lights flash when arm/disarm and when the remote start too. So I don't know I'm at lost here. What could of happen? 002B07164993

1

2014 ford escape turn key. Yellow light wont go off between keys.

001a06 851267 yellow light stays on, ignition doesnt light up when pressing program button. No red and blue led flash. Yellow light stays on even if yellow and purple/yellow wires are disconnected.

0

Pairing. No flashing blights to pair key

Hello. I 've purchased the evo-all remote starter. I've purchased the flash link. Updated the software from the online app. When I plug it in I get the solid blue light, plug all the other connectors, key in ignition to run position, but I do not get the lights flashing to pair the key to remote starter. What is it that i'm doing wrong. Followed all the steps even checked on youtube and I get nothing. Please help. Thanks

0

flash. program

Hello. How can I get my module flashed, I thiught that when you would order for a specific vehical that it would be flashed already and it would be plug and play, 2017 jeep patriot,

0

Can’t flash the evo one module

Not sure if it’s relevant but I did update to the latest recommended firmware, but for some reason the 3 buttons on the bottom right just pop up as I plug it in the USB port but then immediately disappear thus I can’t flash the module. Any suggestions? Tnx

0

2009 Audi s5 manual evo-one with thar-audi blue led stays solid will not program

2009 Audi s5 manual transmission, keyport and start/stop button with evo-one with thar-audi t harness. The blue led stays solid when the ignition is turned on with the keyport and I am unable to program. I have checked the yellow starter wire connection to the clutch bybass and the connection seems solid. The 12v to the juction box is getting a reading and good. The can high and low are also connected good. The connection for the vehicle is clipped together and the plug for the evo-one is connected as well. The 16pin is also plugged into the keyport. When I plug the data cable in while holding the program button the led turns blue. I plug in all the other cables, insert the key, and press once WITHOUT pressing the brake. When I press and release the the program button the blue led remains on as if nothing has happened. Any help please?

1

Evo-FORT4 won't program

I am trying to install an EVO-FORT4 with t-harness on a 2012 Ford F150. Programmed to firmware v71.47 After connecting t-harness and plugging in the OBD connector, I try to program the EVO. While holding the program button, im plugging in the power connector and releasing the program button when the red and blue lights illuminate. Then connecting all remaining connectors. Then I insert key 1 for 3 seconds, then key 2, then back to key 1. The red and blue lights stay illuminated and no other lights illuminate. / Any ideas on what is wrong?

1

F150 pairing Blue light doesn't flash when sequence is followed

Hello, i recently bought a OMEVOALL version 6 firmware 71.34 OMEVOFORT preloaded with a THAR-Ford3 T plug for my 2018 f150. Following your instruction guide and this online video https://www.youtube.com/watch?v=3bpmiYwslSo , i am unable to get the blue light to flash after turning the key to the on position like in your guide and the video. My truck is equipped with a stock hood pin sensor. Any assistance would be appreciated.

0

Nissan Rogue 2014 Push to start - Blue light does not flash when start pushed

Following the steps. Program button pressed when data plug in. Stop on blue. Blue stays solid. Plug in rest of plugs. Press start once (no brake pedal) and all Evo-all module lights turn off. Nothing else happens. This is where the blue LED should flash three times, but it does not. When I press stop again (after waiting a bit) blue light goes on solid. Testing remote start (press 3 times) nothing happens. Blue light stays on.No remote start occurs. On a side note, it did flood the Car with gas, as I heard the feul pump run and had to hold hte starter down for almost a minute to clear it. Bought as part of T-harness kit Evo-NIST3. Also, Do I need to install Hood switch and valet lock if I have an Evo-all and Fortin T-Harness?" Service # 001A06 859857 Firm v 4.18 Hardware ver 6 Date 10/2018

0

Can't finish programming Evo one on 11 forte since blue led does not flashing.

I try to program my 2011 Kia forte without a pats wire and the blue LED does not flash when you turn the key on. I checked the can bus wires and they both have 2.5 volts I do not believe that I have switched them. What should I try next?

0

ford explorer 2015 wont program the keys, lights stay blue and red, never flash or turn off

i have a 2015 ford exploder, i bought the evo all for it and the flash link, have all the connections and wires connected as stated in the wiring diagram, install the t harness and made my connections to the obd wires can hi and can low,, plugged in the 4 pin power connector, stopped the lights at blue and red installed all the other connections, did the key program as directed key 1 key 2 and then key 1, nothing ever changed on the module, lights stayed continuosly lit up, the only that ever happened was when key 1 was insterted for the 2nd time the doors locked. no lights ever changed on the module and the keys never programmed. i have the 3 button setting set on the flash link program

0

Evo all wont flashing blue light in programming!

Hi got problem with my evo all i got mazda cx7 2011 follow all connection tripple check my wire connection, it work i got remote start my vehicle works but door lock unlock wont work, then try to master reset and program vehicle again in step 4 program intructions should i get a flasing blue, when i turn the ignition to run position but i got notthing my blue light was off nothing happen. Can give me some ideas i reallly appreciate this thanks.

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue