Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

01/09/2016

 Dodge William Thomason (130Pts.)

0

Blue LED does not flash 2014 Dodge Charger SE Step 10 turns off when PTS pushed Can Hi/Lo OK...Brake?

I have been through the programming steps 3 times. Was somewhat confused as to whether I should push on the brake (as in "hold down brake and push button to start" for normal starting) during programming steps so I tried both ways. Both times, all goes well until step 10 of the programming sequence. With the Blue LED on solid, when pushing the start button once to turn on the ignition, the blue LED turns completely off and does not flash. I read elsewhere in the Dodge FAQ where it was suggested to connect red/green A18 wire to brake pedal wire, but in my install guide (#12211 - Stand Alone for CHRT6 with T Harness for Automatic Trans Only), the connection diagram says to connect wire A18 to the parking light switch wire which is how I have it. Just to note, when I do not press the brake pedal during programming, the car goes to run position, but does not actually start whereas when I do press the pedal, it does. This seems to have no effect either way on the situation with Blue LED (behavior is same either way). I have double checked and can-bus hi/lo wires are correct and not reversed. Hardware version is 6, firmware is 74.25. Thanks for any advice you may have!
Login to reply View 1 answer(s)

24/02/2016

 Dodge Daniel Oliveira (130Pts.)

0

Blue Light not flashing on program/ Are wires correct?

Hi I wired my fortin system all up and was trying to program when it would never get past the step where its supposed to flash blue rapidly. Im also not sure which wires to pick up for ignition and from door pin because the fortin instructuons tell me a purple wire on the driver side, then wire color tells me on passenger side. the ignition wire i believe i have correct but there were a couple of pink/ white wires. nothing is specific enough on where to find the wires.
Login to reply View 2 answer(s)

24/02/2016

 Dodge Daniel Oliveira (130Pts.)

0

Blue Light not flashing on program/ Are wires correct?

Hi I wired my fortin system all up and was trying to program when it would never get past the step where its supposed to flash blue rapidly. Im also not sure which wires to pick up for ignition and from door pin because the fortin instructuons tell me a purple wire on the driver side, then wire color tells me on passenger side. the ignition wire i believe i have correct but there were a couple of pink/ white wires. nothing is specific enough on where to find the wires.
Login to reply View 2 answer(s)

18/07/2015

 Dodge Donnie Maxwell (210Pts.)

0

Evo all not flashing blue when turn key to on position

2014 tip key Grand Caravan. Using Evo all (no tharness ) and titan ts1;2 remote starter. Not in data mode. Successfully programmed my fobs Successfully programmed Evo all with flash link However when I go to learn the vehicle to the Evo all, as soon as I turn the key to the o. Position (with the blue light currently solid) it turns the light off. It will not blink Any help would be appreciated! TYIA
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue