Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

23/10/2024

Jeep G Trob (130Pts.)

0

EVO-All and CHRT4 - no connection type option

Greetings, Programming an EVO-ALL for install in a 2012 Grand Cherokee PTS, planning to use a CHRT4 T-harness for install. When programming the unit with the FLASH-LINK, firmware 59.02 in the section for selecting 'Connection Type', it only presents 'Wire-to-wire' option...is that correct?

0

EVO-ALL will no longer go into Solid Blue Key programming mode after programming button is released?

After an almost successful key programming where the Decryptor completed successfully with the EVO-ALL, Unfortunately, I did not replace the R-LINK with the TB-VW first before I reconnected the EVO-ALL. When I replaced it after it did not successfully start and gave 5 Red Flashes/Beeps. So I am trying to start over at key programming step 1. When the programming button on the EVO-ALL is released on the Blue LED flash, the Blue LED just goes out instead of staying ON solid. After reconnecting the remaining connectors to the EVO-ALL and pressing start button the yellow LED comes on. It seems like the EVO-ALL is damaged if it will not go into key programming mode or perhaps the RLINK is no longer functioning, This is not a wiring problem since key programming worked the first time. I have no way forward can someone please help?

0

Does CHRT7 require any splicing or tapping for a 2024 Ram?

Considering buying a CHRT7 or CHRT6 for my 2024 Ramy 1500 Rebel with OEM remote start and keyless entry. I looked at the install guide, but its not quiet clear whether it requires splicing/tapping into any wires. (especially the parking lights, ignition, CAN low and High). Thanks

23/09/2024

Fiat G M (14710Pts.)

0

FIAT 500 A5 and A6

I set A5 and A6 to OFF...Wouldn't that be the culprit?

0

infiniti evo-all---evo-key

Hello. Is there a diagram (better if it is standalone) for evo-all such a connection on 2015 infinity Q50, like evo-key? By RX-TX

0

how much parisitic drain does the EVO-START LTE add to Evo All or Evo One and does it goe into sleep mode to minimize it

21/05/2024

Jeep G M (14710Pts.)

1

2022 wrangler

Hello. I installed evo-all on a 2022 Wrangler. When registering, the decryptor wrote: "DCRYPTORS LIMIT HAS BEEN REACHED FOR THIS CAR...What should I do?

0

After step 13 of programing, all three lights are flashing not just yellow and red.

While programing the Evo All, stand alone starter, with mazda t-harness, I'm not getting the yellow and red flashing lights after step 13. Instead all three lights flash at the same time. If I hook it up to the flash link to use the Dcryptor, it's says there is incomplete key information. I don't know what to do from here. Any suggestions. I did try a factory refresh but am getting the same thing. Everything seams to go right up to step 13.

0

will an evo all operate as a stand alone oem key remote start in a 2016 fiat 500

2016 fiat 500 highline 2 door coupe with a 1.4L none turbo, automatic. I wish to install the evo one as a low power stand alone remote start operated by the oem keyfob . will this work?

0

2015 outlander euro

Hello. I also tried the master reset as you told me. I tried another device, which I tried on Ford before (001A07391859), but "take over" is not possible... it says on the monitor that the immobilizer system needs service.

0

2015 outlander take over

Hello. I installed Evo-Al for 2015 Outlander (PTS) Standalone. After remote start-up, we go in the car, I click 2 times on the Start-Stop button and he writes that he does not see the immobilizer (like this), and the engine turns off when pressing the brake.

0

no blue lights when programming oem key

programmed and wired correct, no blue lights comes on during final step of turning ignition on with oem key 2008 dodge ram 2500 diesel

0

Evo-all stand alone

Can I use viper remotes on the evo-all stand alone with the xl202 and if possible is there instructions for this Thank you

09/12/2023