Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

2015 outlander euro

Hello. I also tried the master reset as you told me. I tried another device, which I tried on Ford before (001A07391859), but "take over" is not possible... it says on the monitor that the immobilizer system needs service.

0

2015 outlander take over

Hello. I installed Evo-Al for 2015 Outlander (PTS) Standalone. After remote start-up, we go in the car, I click 2 times on the Start-Stop button and he writes that he does not see the immobilizer (like this), and the engine turns off when pressing the brake.

0

evo-one stand alone installation

I installed the Evo-One (standalone) on the outlander sport today. Was it necessary to flash and bypass and remote start, or is it just the remote start?

0

EVO-ALL StandAlone A2/Purple/Lock and A3/PurpleWhite/Unlock Availabilty?

RE: EVO-ALL Stand Alone Installation in 2017 Mitsubishi Outlander (NOT Sport) with Push-To-Start (FastKey) While installed in this manner, can the can the A2/Purple negative input lock trigger and A3/PurpleWhite negative input unlock trigger wires be used to send lock/unlock signals onto the CAN BUS? If yes are there any restrictions? If EVO-ALL alarm mode is enabled, must it be disarmed first, or will negative unlock trigger via A2/purple still operate? The intent here is to create an alternate mechanism to unlock the car for when it is more convenient to leave my keys inside (with FastKey properly RF shielded of course). If the CAN BUS lock/unlock interface in the EVO-ALL is enabled in this mode, then that will make the installation trivial as it is already present. Thank you.

0

EVO-ALL StandAlone A2/Purple/Lock and A3/PurpleWhite/Unlock Availabilty?

RE: EVO-ALL Stand Alone Installation in 2017 Mitsubishi Outlander (NOT Sport) with Push-To-Start (FastKey) While installed in this manner, can the can the A2/Purple negative input lock trigger and A3/PurpleWhite negative input unlock trigger wires be used to send lock/unlock signals onto the CAN BUS? If yes are there any restrictions? If EVO-ALL alarm mode is enabled, must it be disarmed first, or will negative unlock trigger via A2/purple still operate? The intent here is to create an alternate mechanism to unlock the car for when it is more convenient to leave my keys inside (with FastKey properly RF shielded of course). If the CAN BUS lock/unlock interface in the EVO-ALL is enabled in this mode, then that will make the installation trivial as it is already present. Thank you.

0

EVO-ALL ALARM Mode - Disarm without remote

With respect to using EVO-ALL in standalone Remote Start + Alarm mode enabled, if the EVO-ALL alarm is armed by OEM keyless entry remote control, but the remote control is subsequently lost or the battery dies, how would one disarm the EVO-ALL alarm? (In other words, no functioning remote control is available, but the ignition key is available.) Thank you.

0

2017 mitsu outlander sport standard key

the guideskips right over the outlander sport standard key and go s to the 2018 pts , do we have a solution for ths car 3 lock

0

2011 Mitsubishi Outlander Sport wont start

I installed the evo one remote starter in my 2011 Mitsubishi Outlander Sport push to start folowing the instalation guide but the car doesn't want to start. I am using the 3x lock buttonon myoem remote to start the car. I already program function 38 for that and 31 for the lightswith the flashlink. Car is automatic transmission and i cut the yelow loop wire. The module was succesfully programed. I have the solid blue light then i pressed the push to start button twice and i got blue light flashing which according to the guide is programmed. When i try to start the car the evo one module start with red light then yelow and blue and then it stops. I have nothing lighting on the dash and my push to start button on the car is flashing orange and then it stops.I double checked all the wirings. I also tried with firmware 4.18 but with this firmware the evo one is not doing anything at all when i press 3x lock button to start it. Is there specific firmware for my car that i have to use? Also i notice that the pink ignition wire is not connected to the car ignition. Is that supposed to be like that?

0

Evo one 3xlock remote start not working, used guide #16811

I followed guide #16811. Bypass set up was done according to the guide but 3x lock is not starting the vehicle when pressed. The blue led light does flash when lock and unlock is pressed. Is there something that i missed with the remote start options?

1

2012 Outlander Sport PTS will not start after installation

I installed an Evo-One (AX-One) in my wife's 2012 Outlander Sport. After after all the wiring was complete, I went to program the unit as per the directions only to find that vehicle will not start. It will not turn on. The car will not acknowledge the Push-To-Start button. Pressing the button only a yields a red back light, there are no other chimes and the display doesn't light up. I reconnected the CAN wires that were cut and the vehicle powers up and starts fine. I went back over the wiring diagram, tried again, and still had no sucess. Is there something that I could be missing? Has anyone else heard of this issue?

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer