Questions & Réponses

hi, i worked on  a 2016 mazda CX-3, AUTO transimission ,push to start.

i use EVO ALL+MYCAR mobile control.

flashed the EVO ALL with 71.[44] firmware. STAND ALONE CONFIGURATION: D1,H2

connected all the wires. EXCEPT: parking lights(optional), hood pin

now I'm stucked at programing step 13. The vehicle's ignition turn ON, then nothing happened, The Yellow and Red LED’s will NOT come on. then ignition turns off.

when connect the EVO ALL back to computer, it says DCryptor: THE IMMOBILIZER DATA RECEIVED FROM THE MODULE IS INCOMPLETE.

i have tried 2 different EVO-ALL , same problem.

2016 Mazda 3 Fortin EVO-MAZT1 Stand-Alone add-on

So when I go to start the programming the first time I turn the car on like the video (https://www.youtube.com/watch?v=5ETmJn9RIlE&feature=youtu.be) the security indicator flashes quickly for about 30 seconds.  if I turn it on a 2nd time like in the video the security indicator light is only on for a few seconds like it's supposed to.

If I wait to turn off the car until after the security indicator stops flashing then the yellow light does not turn off.

if I only wait the 3-5 seconds and turn off the car the yellow light will turn off and the security indicator will flash quickly for the 2nd key also. and the yellow light will turn off but the red and yellow lights don't start flashing and it doesn't turn on and off the car.

I have tried removing the batteries from the key fobs and trying that but I might have messed that up and will try that again.

is the hood pin and wiring required for programming? because I haven't hooked that up yet.

I am looking to install the EVO-All with the THAR-MAZ1 t-harrness in standalone configuration in a 2014 Mazda 3 (push-button automatic), and the installation guide states that 2 key fobs are required to programm the evo-all, however I only have 1 key fob.

I want a confirmation whether the evo-all can be programmed successfully with a single key fob, and clarification on what that process would look like? Should I simply skip the steps for the second key fob or follow the steps using the first key? 

Installation Guide page 8: https://cdn02.fortin.ca/download/62681/evo-all_ig_tsa_bi_maz1-3_pts_2014-2017_door_v2_e_62681.pdf

Hi,

I have a 2014 mazda 3 automatic push to start, and I want to have the oem remote start using the evo all stand-alone with t-harness. I've followed this guide: https://cdn.fortin.ca/download/62681/evo-all_ig_tsa_bi_maz1-3_pts_2014-2017_door_v2_e_62681.pdf and I've successfully programmed the module per the guide, the last step was the rapid blue light flashing and that did happen (the only thing I didn't do was set up the parking lights since it was optional). Only the remote start function doesn't work. I've played with the settings a bit and always have c1 and d1 on, I just tried turning D3 on and it still didn't work. I also have D2 on, and when I do the 3x lock, the yellow hazards flash on my car 3 times, and then the door unlocks like D2 states, and then after a few seconds they flash again 3 times, and the door unlocks... and then nothing happens after that. Am I missing settings or anything else simple? Or anything else?

I had another evo-all with tharness that I master-reset after finishing the programming, and then eventually called tech support and they said that evo all would no longer work with my car because I did that. 

One other note: only one of my keys seems to work with the unit; its the only one that will make the blue led flash when I press the lock button that is. From other questions it seems the other key is a clone and won't work with the evo all or something, which I'm fine with, as long as I can get the original one to actually start my car.