Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

Program EVO ONE

For 3x lock from the OEM remote you need to enable option C1 in the bypass and option 38.2 in the remote starter. How do I enable option C1 and option 38.2 for a 2015 legacy automatic keyed start?

10/01/2023

Kia n h (230Pts.)

1

Why won't my Evo-One move past step 4 on programming?

I have verified the correct firmware, proper voltage on yellow wire A1, and correct can-bus wiring.I have constant 12v with a good ground. When I turn the ignition to run the blue led that is supposed to flash 10x's turns off. I installed accordind to the install guide provided through fortin's website.I have followed the troubleshooting guide and get stuck after confirming all 5  steps

The first 3 steps in the programming are very straight forward. If you cannot pass these steps verify the following:
1- Firmware: Ensure you have flashed the correct firmware to the module as indicated in the installation guide.
2- Power & Ground: Verify the module is receiving a constant 12 volts and has a good ground.
3- Yellow Wire (A1): Verify this wire is on the correct ignition wire. Their should be 0 Volts present during the first 3 steps.

If the Blue led does not flash common issues would be the following:

1- Yellow wire (A1): Not connected to correct ignition source.
2- Can Bus Wires: If these are reversed or connected to the wrong can bus wires the module will not program.

0

2019 toyota 4 runner push to start won't program evo one

Does key bypass need to be done before flashlink manager?

0

I can not get evo one to link with imoblizer on 2000 excursion

I purchased a flashlink programmer and still can not get this to work correctly. I also purchased a RF641 key fob set and still no luck. It cranks the ignition as it should but will not activate the imoblizer bypass. I have tried to program this at least 50 times using a stopwatch. I have also checked the wires and probed them no less than 20 times. I get a red light as normal then insert the first key for 3 seconds with solid red light and yellow turns on solid as soon as ignition is activated. Insert second key and yellow stays lit and a second into it the red starts flashing until the both go out. Can you please help?

0

Evo-chrt6 ram 2019 classic when programing key cant get past blue light

Blue light cant get past

0

Can't get the solid blue light

Hello. I have a 2017 Jeep Patriot, pluged the t-harness to immobilizer, connected the 4-pin connector while holding the program button and all 3 lights keep flashing. How can I get the solid blue to program. Thank you

0

infiniti m35x evo all does not program

hello, I just installed an evo all in an infiniti m35x 2006, I have made all the corresponding connections but at the time of programming I find a problem, the instructions say that at the moment the blue light of the evo there is set flashing (last step) press the start button to turn off the vehicle and at that moment the blue light should turn off, but the problem is that it turns off but immediately the yellow and red light start to flash intermittently without stopping and so the evo remains all alone until I completely disconnect, what can I do, i checked the cam hight the cam low and the other connections and I notice all of them well.

0

Re-program tach?

I wired up an Evo-all to my '05 Lexus GX470 with a Viper alarm/remote start system. It had been working perfectly find for the past few months until I tried remote starting and the remote FOB ran out of battery right when I pressed the remote start button. Now when I try to remote start, the vehicle will start for 1-2 seconds, shuts off, and attempt to keep restarting over and over again. I spoke with Fortin tech support and they told me to re-program the tach. I asked if it was the same as re-programming it all over again from the start but the tech support just kept repeating "re-program the tach." Based on the install manual I used from your website, the only "programming" I needed to do was the bypass. How do I just program the tach?

0

Remote start works but not waiting to start for diesel 2011 ram 2500

click the lock button 3 times and the truck will start. However it is not delaying the start like you would for a diesel pickup for the grid heater. I have flashed several firmwares and play with the settings but can't find any way to program in the delay. any suggestions here? I have screenshots but cant upload them to this forum.

0

INT-SL+ Won't Program

The light will come on solid but never goes to the rapid flash stage. This is an install in a 2003 Chevy Cavalier. Hardware Vr. 2 Firmware Vr. 3.01

0

My EVO One doesnt program

SO i bought the kit for the plug and play for remote start for my 2015 rav4 along with the T Harness. everything is installed correctly. I am running on the 79.49 bypass and 1.24 on the remote starter. it doesnt seem like it wants to go into the programming mode. i have held the buttion so the red and blue light stood soild than i plug in all the wires as followed by the instructions. it blinks 9 times and pause. i turn the ignition on but nothing happens please help.

0

Is the yellow light on the module supposed to light up when both keys are inserted for programming?

3

What is the correct way to connect wires?

T-Taps, Butt connectors 2 pounds of solder I've seen and heard it all...most of the time resulting in a headache and lost time. So i thought i would break it down and show the 5 easy steps to make a good quality and secure connection in a vehicle.

The 5 Steps are as follows:

1- Strip back the inulation of the wire you wish to connect to.

2- Seperate the braid to create an opening in the wire.

3- Insert the wire that is to be connected into the opening.

4- Close the wire.

5- Finally twist the wire around securing them togehter and finish it off with some electrical tape.

0

Remote start works but not waiting to start for diesel 2011 ram 2500

click the lock button 3 times and the truck will start. However it is not delaying the start like you would for a diesel pickup for the grid heater. I have flashed several firmwares and play with the settings but can't find any way to program in the delay. any suggestions here? I have screenshots but cant upload them to this forum.

0

2010 4 Runner evo-all wont program

I have connected an evo-all, firmware 79.43 with a crimestopper remote start on a 2010 toyota 4 runner with a g labeled key. Connecting at obd2 violet wire (can high) white wire (can low) and green wire (immo data). Once I get to step 5 of programming the evo-all only flashes red. Are there any other can high, low and data wires?

0

Option change - program again? black 4 pin cable? = '12 Ram 2500 Diesel

Hello Fortin, Now that it's cold out I pulled out the evo-all and connected to my PC, updated to the recommended firmware update (just below the beta one), changed my idle time to longer, saved options successfully, the quite the program. Do I need to program the truck/evo-all again using the button/directions on page 7 of the harness which is a THAR-CHR4 ? Since I am here: 1.) I have noticed sometimes like 5% of the time (1 out of 20 attempts) I here a sharp metal sound like it's turning the starter a little too long or something. Kind of like when someone turns a key when an engine is already running, but in my case it rather a split second of that sound, however it's enough for me to notice it and make me cringe. 2.) 5% to 10% (1 to 2 times out of 20 attempts) when my truck is starting up it has a stall like it goes to crank over half a crank, and then tries again and then it starts up. I don't here the metal sound like above and I see no correlation between the sound above and this stall. I also don't see it correlating to whether I unlock it or not before it starts. They seem like separate issues. I don't mind this issue, but the metal sound seems bad. What is going on with #1 and #2? Neither of these issues has ever happened using the key and only when using the lock-lock-lock start. Since Ram changed in 2013 maybe my 2012 has a 2013 starter system or something??? I love the system, and I'm hoping what I am experiencing is no big deal. Oh,its a 2012 Ram 2500 Diesel and has 20k miles, basically brand new. THANKS FOR YOUR TIME!!!

0

Evo-All won`t program

2006 Saab 9-7x not using the data link to the remote starter, just analog. I connect everything up and try to program the unit to the vehicle.as per the instructions (hold button, connect data link connector, let go when blue LED on, turn key to run...). When I turn the key to run, the blue LED does not turn off or anything. Waited for more than 15 minutes and nothing would happen. PPL/YEL wire to OBD wire is connected correctly. Tried repeatedly and still the blue LED stays on. Just one note on this vehicle. You have the same programming for this vehicle as for TrailBlazers an Envoys. This vehicle is different than all the other trucks in this series in that it uses PassKey 3 and NOT Passlock like the others in case that makes a difference.

0

Evo-All won’t program 2011 Civic

Had the unit programmed, fully functional. Unplugged to change a feature, and now will not program. It will enter the correct mode, however when I attempt to turn the ignition on to learn the vehicle, no lights come on. I have reflashed the firmware 73.28, and still nothing. Any ideas?

0

I cant get through the programming on evo chrt6 2016 challenger

2016 challenger push to start , I installed the evo chrt6 and got to step 6 the red light on and it would not do anything else I unplugged and started over and the yellow light would not flash after the 4 x button I did a unit reset, I hope i didnt mess up anything in the settings by doing this now it is stuck with the yellow light and it wont do anything Can you check my programming to see if it's good? i am using factory remotes for 3x start what do I need to do? please help

0

EVO-KEY will not enter step 4 of programming procedure. 2008 Kia Sedona

EVO-KEY service number 002A02 040238 Hardware Version 2 Firmware Version 1.07 Date 09/2016 Vehicle: 2008 Kia Sedona EVO-KEY is wired as per Guide #15461, Rev 20140930. Connected to Pro-Start CT-3271 remote starter via datalink. I have confirmed that Data wires are not reversed. I have also confirmed that there is +12V @ ignition wire when key turned to "Run", 0V when key off, and this voltage is being seen at the A2 pin of the 6 pin connector. Steps 1 to 3 in Programming Procedure followed and ok, however when key is inserted and turned to "Run" the yellow LED remains on and the red LED remains off. Have reset the EVO-KEY as per instructions here: http://fortin.ca/en/qa/49063/reset-evo-key?show=49063#q49063, with no change in the result. What am I missing to get the EVO-KEY to program? Thanks.

0

EVO ALL in 2010 Lincoln MKX won't program

I reviewed the other post on this exact issue. At first attempt programming (using programming 3--2 keys) the red led flashed and then blue led flashed. The vehicle wouldn't remote start. I attempted a dozen times changing firmware (4.18, 71.39, 71.35, 71.34, 71.11) and programming using the two key method as well as decryptor process and single key. When attempting to program using the two key method, the red led does not flash, nor does the blue led flash. When using decryptor method, after uploading/downloading and updating the module, the vehicle will not remote start, the security light flashes on the dash indicating no valid key. If I hold the key next to the barrel it will remote start. i swapped out the evo-all for another, same result. I swapped out the evo-all for an evo-ride, the red led does not flash when I press the program buttton. RX (lt blue/blk) is connected to the yellow/org pin 4 of transponder TX (lt blue) is connected to purple/grey pin 3 of transponder connector. I tried swapping RX and TX, module wouldn't go into correct programming mode. I tried using the guide for Ford Edge, connecting evo-all relay output (Wht/blue, wht/red) to +12v, ign. 5 hours troubleshooting this thing. Normally changing firmware solves these type of issues, but I am at a loss.

0

2012 Chevy Cruze EVO-ALL Will Not Program

I cannot get my EVO-ALL to program properly in stand-alone mode in my 2012 Chevy Cruze (not push button). No matter what I do, in both the standard programming method and the DCryptor method, the very last step with the flashing blue light never occurs. In standard programming, I get to the last part of step 4 after the yellow led flashes 10x and the blue light never flashes. In the DCryptor method, I get to the very last part of step 7 where the blue led turns on, then blue and red turn off, then yellow flashes and then turns off. Again, the blue led never flashes afterward. I went ahead and ran the DCryptor portion in Flash-Link and it seemed to succeed, but I am still unable to start the car in stand-alone mode.

I've double checked my connection to the ODBII connector with the brown wire, and I'm using the THAR-GM1v2 harness. I've also tried a factory reset and flashing older firmware versions. Nothing has made any difference.

0

Evo-ALL + 2002 Toyota Sienna bypass wont program

I am attemping to install a ProStart 2-Way LCD Remote Starter, 6-Button onto a Toyota Sienna 2002 with Fortin EVO-ALL bypass module. I have made all the necessary connections to the remote starter, programmed successfully; doors, locking, unlock worked. Now I believe, my problem lies within the EVO-ALL bypass. I followed this guide: http://fortin.ca/download/5801/evo-all_toyotalexus_regconfig_cahierd20120813.pdf (connection 2, program 1) posted on the fortin website. When I went to program the bypass module it stayed at the red solid LED and would not flash red rapidly for 10 secs. My questions are:

1. The remote starter in the mode 4 function 4, it has 3 options: 1- way ADS (D2D), 2-way XpressKIT (D2D) and 1-way Fortin(D2D). So now, which one should I select? . I've try using 1-way D2D mode in the remote starter and hardwiring the bypass data link wires (red to +12V and black to ground(-)) and still doesn't programmed. I also tried switching the option to 2-way XpressKIT, bypass wont program.

2. Following the above question, would I need to use a flash link manager to change my Fortin bypass to Fortin2 (2-way D2D)? Is this an option?

3. The guide doesn't state that this vehicle need to connect the 5 pin CAN BUS connector. Am I correct?

4. What can I possibly do to resolve this?


Thanks, 

0

Evo GMT-4 will not program for 2008 GMC Sierra 2500 Diesel

I purchased an EVO GMT-4 for installation in a 2008 GMC Sierra SLT 2500 HD. After instalation of the unit with the T-Harness, I attempted to program the unit. I followed the directions, but after I turned he key, instead of the blue light flashing, it just turns of and stays off. I attempted the programming several times to no availl It came with: Hardware Vr. 6 Firmware Vr. 70.16 Date: 11/2016 EVO-GMTx Preloaded

0

EVO-ALL won't program on 2009 F150

Installed EVO-ALL on my 2009 F150 and can't get it to program with 2 keys. Afetr cycling both keys, light on box is red (steady) and pushing and holding does nothing. I have double checked connections and I have tried several times. Connected to Encore E-5 remote start. I am using 2 original keys stampped with S.

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue