Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

11/01/2021

 Ram Mke Milburn (250Pts.)

0

Stops unless I hit push to start button twice

2019 Dodge Ram Tradesman 1500, new style, 5.7L, auto, Tip start, . Evo One w/THAR6 harness.Using factory lock/unlock/alarm remote, 3X lock to start then unlock to enter the truck.All soldered and heat shrunk connections. Installed back in June, worked great until last week. Starting one week ago, would shut off when I hit the brake even tho I pushed the start button before touching the brake. By accident I found out if I pushed the start button twice before hitting the brake, it would keep running as it had been doing the previous 6 months, what could have changed?...........Mike **EDIT* Now a few weeks later, it won't keep running even when I hit it twice, stops immediately when I hit the brake....any ideas?........Mike
Login to reply View 1 answer(s)

23/10/2020

 Ram Peter Prezioso (130Pts.)

0

Lights stay solid upon intial connection

2017 dodge ram tip key everything is connected correctly but upon initial connection to program when I hold down the program button nothing happens stays solid does not let me select yellow light
Login to reply View 1 answer(s)

01/09/2020

 Dodge John Flynn (160Pts.)

0

2016 Dodge Challenger, EVO-ALL w/ CHR6, now throwing U0415 Check Engine Light

As Title indicates, post installation the client is getting a CEL U0415. It happened to me after programming but I cleared it and figured it was a fluke. According to him, per his Dodge dealer, they have seen this happen with aftermarket remotes starts and also stereos on the Challenger. Any suggestions other than rolling back firmware? When tapping for 12V ignition I grabbed the incorrect wire first time around. It was pink/wht but didn't give 12V with IGN. The snake shows Pin 27 OR 31 at BCM, plug E. 27 was the wrong one, 31 was hardly pink/wht, more pink/yel but did give 12V with ignition.
Login to reply View 1 answer(s)

27/10/2019

 Ram trevor gorniak (2230Pts.)

0

Evo all programming 20019 ram 1500 push start

Install complete and verified go to program evo all and at step 5 instead of the blue light coming on the blue and red comes on checked everything twice called tech support and they said don't worry about it. i ignored the red being on and carried on to next step and all was ok. Has anyone else seen this issue i hope they repair this in the guides so installers dont have these issues
Login to reply View 1 answer(s)

26/10/2019

 Chrysler Charlie Gray (130Pts.)

0

Why does my remote start occasionally shut the car off after a few secconds?

2015 Chrysler 200. I have the evo chrt6 remote start and occasionally when I activate the remote start the car will start then shut off after a few seconds. It doesn't always do this though.
Login to reply View 1 answer(s)

25/10/2019

 Ram Jesse Lockridge (190Pts.)

0

Will any of these products work with OEM remote starter already installed

Hi, I have a 14 Ram 1500, which already has a factory installed remote starter. I'm looking to switch over to Fortin, and use a MyCar RFLink. Can you suggest which product/products i could use to make this work. Thanks! Jesse
Login to reply View 1 answer(s)

18/08/2019

 Ram Chuck Wrang (210Pts.)

0

Evo-all module does not shut off after "push to start button" and shuts off after pressing braker pedal.

I have a 2019 Ram 1500 (newer model, not classic). The OEM remote activates the remote start and is working properly. When I get in the truck and push the "push to start" button once to deactivate the module, nothing happens. When the brake pedal is pushed, it shuts off and I have to restart the truck with the "push to start" button. I have tried programming the module several different ways with no luck. Thanks in advance. Chuck
Login to reply View 1 answer(s)

30/12/2018

 Ram Carroll Parker (130Pts.)

0

Why do I Get U0001 code. Evo chrt6 on 2018 Ram 1500 gas standard key. Everything works fine.

U0001 code 2018 Ram 1500
Login to reply View 0 answer(s)

18/12/2018

 Chrysler Kaden Stratton (240Pts.)

0

Car doesn’t go into gear unless I press brake and push to start button at same time

My car only goes into gear when I press push to start and brake at the same time. Also it says service fob system. What could be the issue? Chrysler 200s 2015
Login to reply View 1 answer(s)

04/10/2018

 Ram Elizabeth Kingston (160Pts.)

0

2014 Ram 1500 crimestopper revo 1.1 hangs on yellow when programming remote

installing a revo 1.1 remote starter on my Fortin Evo All unit chrt6 on my 2014 ram 1500. when programming the remote units i unplug the power cable. hold program button and plug power cable back in. i get a solid red and solid blue. i press the program button and hold until the blue and red lights flash out and come back on. I put the key in the ignition and turn to run position i get a solid yellow. red and blue are still lit. when i push the button on the remote unit to pair to module the red and blue light are suppose to blink to acknowledge the remote unit has been programmed. on my unit the red and blue light go out and only the yellow light remains on. firmware 74.37. In my flash link setting under data protocols everything is greyed out i cannot select F2
Login to reply View 2 answer(s)

04/10/2018

 Ram Elizabeth Kingston (160Pts.)

0

2014 Ram 1500 crimestopper revo 1.1 hangs on yellow when programming remote

installing a revo 1.1 remote starter on my Fortin Evo All unit chrt6 on my 2014 ram 1500. when programming the remote units i unplug the power cable. hold program button and plug power cable back in. i get a solid red and solid blue. i press the program button and hold until the blue and red lights flash out and come back on. I put the key in the ignition and turn to run position i get a solid yellow. red and blue are still lit. when i push the button on the remote unit to pair to module the red and blue light are suppose to blink to acknowledge the remote unit has been programmed. on my unit the red and blue light go out and only the yellow light remains on. firmware 74.37. In my flash link setting under data protocols everything is greyed out i cannot select F2
Login to reply View 2 answer(s)

06/09/2018

 Ram Joshua Lindt (260Pts.)

1

2017 Ram 1500 Tip Start, Will Not Remote Start

Details: 2017 Ram, Gas, Tip Start, CHRT6, OEM Remote Flashed with standalone, T-harness, with built in alarm, 74.[37] firmware, 6.0 hardware. No hood pin, valet switch, or parking lights connected. C1 and D1 enabled, #8 blue wire does not turn red when grounded. Everything seems to be installed correctly. The key programs without issues. Flashes without issues. The blue light falshes each time the lock button is pushed. The yellow light comes on when it is started with the key. Problem: When I attempt to remote start (3x lock button on the EOM remote) nothing happens on the unit or in the truck. No attempt to start, no dash lights, nothing. Any advice?
Login to reply View 1 answer(s)

15/04/2018

 Dodge Angel Enriquez (440Pts.)

0

Programmig not working stuck at step 9

i have double and triple checked my wire connections but when i try to program my THAR-CHR6 and when i get to step 9 the light will not change from Red to blue. I have attempted this multiple times and have followed all the steps so i am lost and really could use some help. Could it be an issue with my unit or is there a trick to this i am missing. I am installing on a 2013 Dodge Journey Push button ignition. *Update* I had intially started i had updated my Evo to the most recent firmware not in beta. I downgraded to 74.22 and was able to get to the next step where the blue light would come on but it would not flash. Flashed it again to a higher FW believe 74.25 but same thing blue light doesn't flash. Otherthing i noticed is on the ODBII port guide says the CAN high wire is brown but there are no brown wires on that harness. The CAN low matches the yellow though.
Login to reply View 1 answer(s)

15/04/2018