Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

evo start 2

I bought an EVO-START2 to add to my EVONE + THAR-ONE-MAZ3 installation. After re-flashing do I need to do the whole decrypt process again? Also do I connect the yellow wire to A1 or E5 onto the harness? Thanks.

0

toyota highlander 2023 telematics wire not as show in the diagram.

dear sir my car is a Toyota Highlander hybrid  2023 I got evo all with thar-toy 13 All connection is good except one connection for the telematics black wire I can not find this wire as you see in the picture what can I do now

0

Output wire for trigger

On the evo one, is there a wire ouput that i can use to turn on my dash camera?thank you!

0

where is door lock data wire? It said blue at driver boot. 2008 GX470

Can someone tell me exactly where is the door lock data wire is? It said blue at driver boot, but there are too many :)

0

STARTER WIRE

Hello How to test a starter wire on a late 2016 / 2017 Mirage / Space Star push-to-start the wire color in my Mirage is Pink/Black on pin 97 and not Blue or Blue/White. How can i test it. Evo-All Thank You

0

Re-wrapped extra fob, now neither works

Original VW starter installed by an installer into a Tiguan after I purchased it. Someone borrowed the car, forgot to take my fob, and decided to pull out the hidden fob from under the dash. The wire coil and black tape are gone; only two bare leads coming out from under the dash remain. I took the battery-less fob he pulled out and wrapped it 12 times with 24 gauge insulated wire, then crimped the two ends of that wire to the leads sticking out from under the dash. It does not do anything. I tried wrapping different numbers of turns up to 16, same. Worse, my main fob stopped working. It does not do anything. Tried replacing battery, same. Tried reset procedure (using physical key, unlock/lock), same. Anybody know what might be going on?

0

Why does my 2017 Ford C-Max Energi SE turn off seconds after successfully initiating a remote start?

I am currently utilizing the Evo One with my 2017 Ford C-Max Energi SE plug-in hybrid in conjunction with the T-Harness. I have checked wiring, factory reset and re-programmed the Evo one, and ensured the recomended bypass/remote starter settings are properly checked. If I had to guess, I would say that becasue my combustion engine does not start when the vehicle is started, until power is required, that the module considers it a false start and shuts down the vehicle. Any advice would be much appreicated. And since I'm here, when wiring the evo one into the horn, is the T-Harness(Orange/Black) wire spliced into the existing connection(Brown), or is the (Brown) horn wire being redirected through the module? The installation makes it clear that it appears that the connection is being redirected, but I wanted to be sure. Thank you!

0

Evo Start 2 says running for a few seconds then says off but car is running

Installed Evo all with twvw1 harness and Evo start 2 yellow wire from Evo start 2 connected to purple/yelllow wire from Evo All (ign + out) Evo start will say "Engine On" but the tach needle doesn't change, and then it says that the engine is off the next status request I send. But the car is running. It will show that the voltage is 14+ and the temp rising in the car. But shows the engine off.

0

DOOR LOCK UNLOCK WIRES AT BCM OW DO I CONNECT THEM? DO I REMOVE EXISTING?

DO I REMOVE THE EXISTING WIRES AT THE BCM AND INSTALL THE( EVO ALL) WIRES IN THERE PLACE?

0

Black 20 pin connector vs White 20 pin connector

Is there a difference between the black and white connectors? Connected the yellow wire from a black 20 pin connector (Evo All).....NOTHING, replaced it with the yellow wire from a white connector... worked after that. Are they pinned different?

0

Evo-one with T-Harness will I need to install 6 pin power connector

Hey all, I have a 2016 Audi A3 8V Push to Start. & before I begin my installation here. I am following the given guide for the no key required Evo-one and T-Harness (thar-vw1) & was wondering if I also need to install the 6 pin power connector that came with my Evo-one. As the guide I am following doesn't specify for my vehicle. Thanks!

0

2020 corolla hybrid start wire & override switch

Today I installed the EVO ALL in my 2020 Toyota Corolla GR Sport Hybrid, unfortunately the hybrid start wire was too short because I wanted to mount the module all the way on the left behind the cover for easy access. However upon testing all still seemed to work (blower goes on, which for me is the most important, both in winter and in summer). My question is what exactly does this wire? I can simply extend the wire, but I feel a bit hesitant cutting and soldering the original wire (it is very thin, so I don't want to use a splice connector). I guess this is for the car to be able to start if the battery becomes low because of the blower (and lights and radio) going on? Also was wondering what the override switch does, suppose only as an emergency for when the EVO for some reason fails? There are a lot of spare wires, from the big white connector they seem spare I/O, but from the smaller white connector there are 2 orange wires which don't appear in the instructions. Wish the instructions explained all the connections a bit more.

0

2020 corolla hybrid start wire & override switch

Today I installed the EVO ALL in my 2020 Toyota Corolla GR Sport Hybrid, unfortunately the hybrid start wire was too short because I wanted to mount the module all the way on the left behind the cover for easy access. However upon testing all still seemed to work (blower goes on, which for me is the most important, both in winter and in summer). My question is what exactly does this wire? I can simply extend the wire, but I feel a bit hesitant cutting and soldering the original wire (it is very thin, so I don't want to use a splice connector). I guess this is for the car to be able to start if the battery becomes low because of the blower (and lights and radio) going on? Also was wondering what the override switch does, suppose only as an emergency for when the EVO for some reason fails? There are a lot of spare wires, from the big white connector they seem spare I/O, but from the smaller white connector there are 2 orange wires which don't appear in the instructions. Wish the instructions explained all the connections a bit more.