English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

13/12/2024

 Mitsubishi G M (15380Pts.)

1

Remote start of the 2023 Outlander

The start-stop button is given a minus twice, with an interval of 3-4 seconds. We have to move the instrument panel frame to get to the button connector. There was a whitish line. I fitted a 12-ring loop to the rear cylinder of the start-stop button. I removed the battery from the key and attached a 2 cm diameter 12-ring loop to the logo. I cut the gray wire on the brake connector with the relay contacts and gave a plus to the light blue wire. To turn off the engine, it takes 3-4 seconds to give a minus to the start-stop button, and then a minus impulse to the door button... Behind the kick panel there was a light blue wire. The door lock-unlock lines were also there...purple and beige.
Connectez-vous pour répondre Voir 1 réponse(s)

12/12/2024

 Mitsubishi G M (15380Pts.)

0

2023 OUTLANDER

Hello. 2023 Outlander (Euro) does not have a standard remote start. Is there another option for remote start?
Connectez-vous pour répondre Voir 1 réponse(s)

10/12/2024

 Mitsubishi Chitos (410Pts.)

0

2018 RVR LED & headights light Flash continusuly after Remote Started

Hello everyone We installed an Evo-One on this RVR 2018 with factory HID headlights and LED Fog light using 23101 guide. We followed the guide to a T, the issue we are have is that as you remote start the vehicle using 3X lock the vehicle starts properly, but if the lights are set on automatic, the headlights and LED lights flash continuously as well if you turn off the lights and remote started the Vehicle the LED fog lights flash continuously both will flash until you take over the vehicle. Has anybody come across this? We think it might be a faulty EVO one module any thoughts please help.
Connectez-vous pour répondre Voir 1 réponse(s)

01/12/2024

 Honda John Klimek (460Pts.)

0

Do I need my original key fob for push-button start? (ie. do I need to carry two key fobs?)

I have a 2021 Honda CR-V that uses push-button start. I'd like to add the EVO-ONE (or similar) so I can have longer distance remote starting. However, do I still need to carry the original key fob?
Connectez-vous pour répondre Voir 2 réponse(s)

01/12/2024

 Kia aut0m0nkey (180Pts.)

0

My fortin evo one remote starter keeps popping up check tire monitoring on 2023 kia forte

When I get in and push my start button, check my tire monitoring system keeps flashing until I hit the brake and then it stops and my car is back to normal.
Connectez-vous pour répondre Voir 1 réponse(s)

01/12/2024

 Honda John Klimek (460Pts.)

0

Do I need my original key fob for push-button start? (ie. do I need to carry two key fobs?)

I have a 2021 Honda CR-V that uses push-button start. I'd like to add the EVO-ONE (or similar) so I can have longer distance remote starting. However, do I still need to carry the original key fob?
Connectez-vous pour répondre Voir 2 réponse(s)

29/11/2024

 Subaru G M (15380Pts.)

0

subaru crosstrek and take over

Hello. I installed evo-one (3x lock) on 2018 Subaru Crosstrek. When opening the door the engine stalls... What could be the reason?
Connectez-vous pour répondre Voir 1 réponse(s)

11/12/2016

 Other Steve Thomas (190Pts.)

0

Help I get this message. DCryptor's limit has been reached for this car.

I had troube getting my keys to program the in the Evo-all. Finally figured out the problem and now it says "DCryptor's limit has been reached for this car" and I can't program my Evo-all. I have the tb-vw, thar-vw1, Evo-start and Evo-all
Connectez-vous pour répondre Voir 1 réponse(s)

25/11/2024

 Jeep tony bacchus (340Pts.)

0

2015 jeep grand Cherokee PTS using evo all climate shuts off with remote start

Installed an evo all a while ago but customer noticed the climate is off when she starts with evo all 3x lock and start 2 When she uses factory remote start or manual start climate turns on no problem It’s turning the climate off the screen says climate off even though she turns it all on before she shuts Jeep off 2015 jeep grand Cherokee diesel PTS
Connectez-vous pour répondre Voir 1 réponse(s)

19/11/2024

 Volkswagen ackktarus (190Pts.)

0

VW Jetta 2015 - No Key even after Decrypt seems to have worked fine

I have installed a EVO ALL on a Jetta 2015 TDI (Push Start - Automatic).  I have the EVO ALL, THAR-VW1 and TB-VW installed as per instructions (I decided to skip the trunk release wiring as I didn't find the feature useful for me case).   The EVO All is programmed with Diesel Option enabled and it went through the Decryptor without any issues.  

When I press the 3 lock sequence,  the dash lights up (I had a previous problem that now brought me up to this point) but the dash says 'NO KEY'.   The car starts if I get the key in the car,  but not if the key is not in the car.   I was wondering what could be the problem.  The only item that I was wondering is that I reprogrammed (changed options) on the EVO ALL but didn't run the decript after,  would this cause this issue?   The car is store off site so I will drive in the morning and try this.   But what other issues could this be?

Connectez-vous pour répondre Voir 1 réponse(s)

19/11/2024

 Ford Mathew Bond (180Pts.)

0

Manual Transmission Prog. & Wiring Ford Focus

Hi, Looking for some information before I pull the trigger on buying a Fortin remote start kit. I have a 2012 Ford Focus, Manual Trans. with Push-To-Start. When I enter the vehicle details it only has a guide for Automatic trans, but the EVO-ONE-411 is compatible with manual trans just no guide. Is there a T-Harness that works with the push to start & manual trans, and would this EVO-ONE-411 be able to be programmed for the manual remote sequence on this car? How much extra wiring is needed? I assume I also have to perform a clutch switch bypass with relays. Thanks for the help in advance, hoping to get this working before the snow starts flying :)
Connectez-vous pour répondre Voir 1 réponse(s)

18/11/2024

 Volkswagen ackktarus (190Pts.)

0

Signs of a decryption issue (Bypass) on a VW Jetta 2015

I have installed a EVO ALL on a Jetta 2015 TDI (Push Start - Automatic). I have the EVO ALL, THAR-VW1 and TB-VW installed as per instructions (I decided to skip the trunk release wiring as I didn't find the feature useful for me case). The EVO All is programmed with Diesel Option enabled and it went through the Decryptor without any issues. But when I press the 3 lock sequence. It doesn't start or crank. I see the red light turns on, and then the yellow light turn on... and it repeats this procedure twice (as per the options programmed). The dash of the car doesnt come on (as expected) during the sequence. I will check the brake lights when I have time but I was wondering if there is possibly something wrong with the bypass. Thanks
Connectez-vous pour répondre Voir 1 réponse(s)

17/11/2024

 BMW G M (15380Pts.)

0

BMW F15, F30...

Hello. I wonder why you don't include BMW F15, F30, etc. in the Fortin list? It's a simple logic: After the bypass relay is turned on (key in the coil), after 2 sec. pulse on a start-stop for 1 sec... After 3 sec. f pulse to the brake pedal for 5 sec. and after 2 sec. a start-stop pulse for 1 sec. (500 Ohm...or 680 Ohm...or 1000 Ohm). I'm struggling to put this together with some kind of autostart, but it would be easier with Fortin.

Connectez-vous pour répondre Voir 0 réponse(s)

16/11/2024

 Mitsubishi Walid Al Shabib (310Pts.)

0

shut off when I press the brake

I am writing to report an issue with my car’s remote start and shutdown process. When I press the lock button on the car key three times, the car starts remotely, as expected. However, after entering the car by pressing the unlock button, I encounter a problem: when I press the ‘Press to Start’ button twice in succession and then press the brake, the engine shuts off immediately, and the message ‘Wegfahrsperre’ appears. Could you please help me understand and resolve this issue?” FORTIN EVO-ONE-MIT2 EVO-ONE + T-KABELBAUM Mitsubishi Outlander 2016 SN:002B04 291538 On the first press, the blue light blinks. On the second press, the blue light also blinks. On the third press, the blue light blinks, followed by the red and yellow lights. The blue light then turns off, leaving only the red and yellow lights on. My issue is that I want the engine to keep running so I can drive immediately, rather than having the engine shut off when I press the brake pedal and then needing to restart it to get going.
Connectez-vous pour répondre Voir 0 réponse(s)

12/11/2024

 Scion Isaiah Byrd (130Pts.)

0

Will the EVO ONE work on my 2016 Scion tC with push button start?

Hi, I see the EVO ONE should work for my 2016 Scion tC but the trim level states standard key. The 2016 model only came with Push to start. No manual key option. Will this work? If so, which T harness should I use? Car is also manual if that matters. Thanks
Connectez-vous pour répondre Voir 1 réponse(s)

05/11/2024

 Skoda G M (15380Pts.)

0

Function D2

Hello. I installed evo-all on a 2022 Skoda Superb... (I specified a 2021 Golf... I connected the CAN under the steering wheel, orange-green and orange-brown... the start-stop wires were blue and purple) I did not enable the D2 function... After all, we still open it with remote start... Lock-Unlock-Lock... It is possible not to turn it on, right?
Connectez-vous pour répondre Voir 1 réponse(s)

28/10/2024

 Honda Craig Beaudoin (130Pts.)

0

2019 Honda HRV, What settings do I have to enable for EVO ONE RM942 for the antenna to power up and learn Fobs?

I Installed the EVO ONE RM942 with Hon8 T-Harness. Three lock on factory fob works remote start function but when I do learn procedure in RFK 942 manual antenna doesn't light up. Tried with turning the key on and off and brake pedal as well as with the valet switch but neither excites the antenna power. Guessing I just didn't toggle the right setting when programming the EVO ONE but couldn't find anything else in the instructions.
Connectez-vous pour répondre Voir 1 réponse(s)

25/10/2024

 Subaru G M (15380Pts.)

0

2015 impreza

Hello. I installed Evo-One on a 2015 Impreza. Does the Evo-One have an input line to lock and unlock the doors? If I put another remote.
Connectez-vous pour répondre Voir 1 réponse(s)

25/10/2024

 Subaru G M (15380Pts.)

0

2015 impreza

The car is Japanese, right-hand drive. I installed the evo-one and it worked, but after a while it stopped working. The engine will start and shut off shortly. The immobilizer LED flashes on the panel...
Connectez-vous pour répondre Voir 1 réponse(s)

25/10/2024

 Subaru G M (15380Pts.)

1

Right hand drive 2012 Impreza PTS engine started

Imo-data turned out to be a yellow wire in the connector where the starter wire and ON2 are. I connected the light blue wire with a black stripe to the side of the car. And the brown wire next to the yellow one, I cut (it interfered). On the red connector of the evo-one I connected a relay with a pair of contacts and with this relay I opened these yellow and brown wires. After entering the car, it was necessary to press the start-stop button twice.
Connectez-vous pour répondre Voir 1 réponse(s)

25/10/2024

 Honda Daze (150Pts.)

0

13 honda accord push to start. Won't OEM remote start, automatic transmission

3x lock module shows blue light response to inputs from OEM key, electrical click and nothing. module shows yellow light when running started normally. Thar-one-hon3, Evo One. Firmware 73.30, function 38:2 is on. Unit option C1, D2 and D6 are on, Yellow loop wire is cut on module SN: 002B04680114
Connectez-vous pour répondre Voir 1 réponse(s)

25/10/2024

 Mazda omair arif (130Pts.)

0

Can someone clarify how to pair a RF remote (in my case the RFK912) on a Push to Start Car (mine is a Mazda 3 2023)

I have the remote start working with the OEM key fob, and have the RFK912 antenna wired in and the Evo-One programmed to support it. But I can't figure out how to get the antenna into pairing mode so I can pair the RF remotes.
Connectez-vous pour répondre Voir 1 réponse(s)

23/10/2024

 Jeep G Trob (130Pts.)

0

EVO-All and CHRT4 - no connection type option

Greetings, Programming an EVO-ALL for install in a 2012 Grand Cherokee PTS, planning to use a CHRT4 T-harness for install. When programming the unit with the FLASH-LINK, firmware 59.02 in the section for selecting 'Connection Type', it only presents 'Wire-to-wire' option...is that correct?
Connectez-vous pour répondre Voir 1 réponse(s)

20/10/2024

 Volkswagen Fatbadcat (130Pts.)

0

EVO-ALL will no longer go into Solid Blue Key programming mode after programming button is released?

After an almost successful key programming where the Decryptor completed successfully with the EVO-ALL, Unfortunately, I did not replace the R-LINK with the TB-VW first before I reconnected the EVO-ALL. When I replaced it after it did not successfully start and gave 5 Red Flashes/Beeps. So I am trying to start over at key programming step 1. When the programming button on the EVO-ALL is released on the Blue LED flash, the Blue LED just goes out instead of staying ON solid. After reconnecting the remaining connectors to the EVO-ALL and pressing start button the yellow LED comes on. It seems like the EVO-ALL is damaged if it will not go into key programming mode or perhaps the RLINK is no longer functioning, This is not a wiring problem since key programming worked the first time. I have no way forward can someone please help?
Connectez-vous pour répondre Voir 0 réponse(s)

14/10/2024

 Volkswagen Dameon Priebe (130Pts.)

0

2015 VW GTI Manual, remote start worked once but now just cranks

Just finished installing an Evo-one LTE in my 2015 VW GTI, manual with push to start (mfg. in 2015) using the TB-VW and Thar-vw1 I had some issues with the first iteration of programming but eventually hard reset the Evo module, reflashed it, re programmed with R-link. Installed back in the car and the remote start worked! Buttoned it all up, got the car in ready mode just to test it and it just cranks, but won’t start. my connections and programming were all fine if it started the first time so what would cause this?
Connectez-vous pour répondre Voir 0 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer