Questions & Answers

I just got a Linkr-LT2. It came with the Linkr-LT1 quick install guide. I followed the steps in the quick install guide but the unit does not work.
The Linkr LT app only shows my car battery voltage and connection signal. The GPS tracking is working fine. The START/STOP/LOCK/UNLOCK
don't work. I searched the internet and found the "mycar installation guide". I followed the steps to learn the Linkr-lt2 to the Evo one. I turned on the "Fortin 2" function on the EVE ONe.  I pressed and held the valet button for 5 seconds but the RED led light on the Evo One did not turn on.

Problem SOLVED. .Linkr LT2 is working fine now...

I found the video on youtube 12voltsolution.  The guy pressed the UNLOCK button on car key several times to neutralize the EVO ONE before he did the following steps.

STEP 6. LEARN THE MYCAR TELEMATICS DEVICE TO THE EVO-ONE
In order to communicate with the remote starter, the telematic system must be learned to the EVO-ONE.
1 - Cycle the ignition to the ON position.
2 - The YELLOW LED on top of the EVO-ONE should come ON.
3 - Press & Hold the EVO-ONE programming Valet button for 5 seconds.
4 - The RED LED on the side of the EVO-ONE will Flash rapidly.
5 - Release the push button.
6 - Press & Release the push button 5x times. Everytime the push button is pressed the parking lights
& the RED LED on the side of the EVO-ONE will blink.
7 - Then Press & Release the Brake pedal.
8 - At that same moment the RED LED on the side of the EVO-ONE will blink once to confirm that the
Telematic device ID has been learned to the EVO-ONE.
9 - Cycle the vehicle’s ignition to the OFF position to Exit the EVO-ONE programming.

I just got a Linkr-LT2. It came with the Linkr-LT1 quick install guide. I followed the steps in the quick install guide but the unit does not work.
The Linkr LT app only shows my car battery voltage and connection signal. The GPS tracking is working fine. The START/STOP/LOCK/UNLOCK
don't work. I searched the internet and found the "mycar installation guide". I followed the steps to learn the Linkr-lt2 to the Evo one. I turned on the "Fortin 2" function on the EVE ONe.  I pressed and held the valet button for 5 seconds but the RED led light on the Evo One did not turn on.

Problem SOLVED. .Linkr LT2 is working fine now...

I found the video on youtube 12voltsolution.  The guy pressed the UNLOCK button on car key several times to neutralize the EVO ONE before he did the following steps.

STEP 6. LEARN THE MYCAR TELEMATICS DEVICE TO THE EVO-ONE
In order to communicate with the remote starter, the telematic system must be learned to the EVO-ONE.
1 - Cycle the ignition to the ON position.
2 - The YELLOW LED on top of the EVO-ONE should come ON.
3 - Press & Hold the EVO-ONE programming Valet button for 5 seconds.
4 - The RED LED on the side of the EVO-ONE will Flash rapidly.
5 - Release the push button.
6 - Press & Release the push button 5x times. Everytime the push button is pressed the parking lights
& the RED LED on the side of the EVO-ONE will blink.
7 - Then Press & Release the Brake pedal.
8 - At that same moment the RED LED on the side of the EVO-ONE will blink once to confirm that the
Telematic device ID has been learned to the EVO-ONE.
9 - Cycle the vehicle’s ignition to the OFF position to Exit the EVO-ONE programming.

I bought the Evo All with the Fortin T6 harness for my Toyota Rav4 2018 Push To start.

I updated the Evo with the newest firmware.  I turned on the  option "Engine Shut down when door is open".  The problem is the engine DOES NOT shut down when I open the door.  I step on the brake and move the out of park, the engine shut down and then automatically starts up the engine again. 

Problem solved.

I stood too close to my car when I remotely started it.  My car did not start so I turned off some of the options.  I reloaded  the suggested options.  My car starts up and shuts down when I open the door.

Thank you !!...............

Hello to all. 

Sorry for the long post but im trying to be as much descriptive as possible.
I would like your comments and advise in the following issue that I had when installing a remote starter on my car. Car unexpectedly died after testing the remote starter. several times. 

Some background:
I have a 2015 Focus SE automatic. It barely has 3000 miles. 
I purchased a Fortin EVO All bypass unit with a CrimeStopper LC1 remote starter. It comes with 2 additional remote controls and All the system came preprogrammed. I could start the car with my OEM keys (by pressing the lock button 3 times) or with the additional key fobs. 

Installation process:
I went ahead and removed the bottom cover on the steering wheel and disconnected both start harnesses (main and immobilizer). 
I then connected the new T-harness. 2 plugs back to the start cylinder and 2 more to the factory car harness. 
I also tapped the CAN high and low and got everything ready for connecting the remote starter unit. 

When plugging everything in to the EVO ALL, I had no issues. I programmed the oem keys on the Fortin unit and finished without any issues. 

I tested the remote starter several times and worked perfectly with both oem keys and the extra long range remotes. 

I finished up by organizing everything inside the console and routing the cables. I was very careful by not disconnecting anything. 

I tested the system one more time and started to have problems. The car wouldnt remotely start.
I got inside and tried to start it normally with the key but no luck at all. The car tried to crank several times (around 3 or 4) every time i push the key to the ignition position but engine wouldn't start. It was a very rapid crank. 
All lights in main console were ok so I didn't think the battery was dead. Also, no errors were shown on the dash. 
Anyways, I tried to jump start the car with another car and this time, it started without issues. I left it charging for 15 minutes and disconnected the jump car. My car kept running. 
When I tried to shift from P to D on the car, just by pressing the stick unlock button, car died again and wont start by its own. Only jump-starting it again would help it start but the same issue when shifting to DRIVE would happen. 

I disconnected all the remote start harnesses and units and tried again. No luck 

I ended up having the car towed to the dealer. I didn't do any other troubleshooting procedure. 

Car Stayed at the dealer for an entire week and they finally got it up and running. They never told me specifically what happened but mentioned that a PCM fuse was "loose". Nothing else. I asked them about this fuse location and they told me that it's not accessible or on the fuse box . That doesn't make any sense. 

I have been trying to find the root cause of the failure because I want to re-install the remote starter again. The thing is that I'm afraid this would happen again and have no idea on how to fix it. This installation should be very easy and the fact that it did work initially on my car makes me think that there was something else that coincidentally happened during the installation. 

After all this, I would greatly appreciate your opinion on my issues. What should I do?


Thanks so much in advance.

2012 Ford Focus wont unlock doors with RF642W remote (locks fine)

Connected everything according to diagram, center lock/unlock button and green/purple wire behind door kick panel.

Start and Shudwon works,  lock works but wont unlock.