Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

PIN Terminal Standards on Fortin T-Harness

Does anyone know what standard pin terminals are used on Fortin T-Harnesses? I was removing a connection at the Evo module and pulled two wires out of the connector. I need to replace the terminals but have no idea the Standard that is used on the connectors. I'd like to purchase terminals to correct the issue. Thank you everyone!

0

infiniti evo-all---evo-key

Hello. Is there a diagram (better if it is standalone) for evo-all such a connection on 2015 infinity Q50, like evo-key? By RX-TX

0

my computer canot detecect evo all in one

0

my computer canot detecect evo all in one

2019 dodge journey cant finish programing decoder

14/07/2024

Subaru ReLyt (210Pts.)

0

2009 Subaru Manual unable to Lock/Unlock during remote start

Good evening, I am trying to get a 2009 Subaru Forester manual transmission functioning with an EVO-ONE and an Excaliber RF kit (listed under compatible remotes). Reference: https://fortin.ca/download/25141/Audiovox%20%20EVO-ONE.pdf First of all, the option for RFLF remote within Unit Options does not exist on any of the remote start firmware options (tried 0.44, 1.26, 1.16 and several others to check). I did attempt to pair the remotes and had mild success with the default RF kit setting. Lock and Unlock seem to work intermittently depending on the state of the vehicle, remote start does work with reserve mode for the manual transmission as long as a lock command is accepted to turn off the engine (configured option to keep engine running until door lock). Currently running remote start firmware 1.16, but had similar results with 1.26 and 0.44 as well. Primary issues: 1) Unable to use factory or Excaliber remotes to lock or unlock the vehicle after a remote start command was sent from Excaliber remotes (regardless if the vehicle was able to successfully remote start or not). What options exist to resolve this? What firmware should be used? Are there any option settings to adjust? 2) Flash limit was reached while trying to test different remote start firmware versions. Can this please be reset? (EVO-ONE, 04/2022, SN: 002B04 271047) Secondary issue: 3) Sometimes when a door is opened after an unlock command, the alarm is triggered and can only reset when unlock is pressed twice on the factory fob (not tested with Excaliber remotes). This was not tested thoroughly so I do not have clear steps to reproduce this case. It did seem to happen more often after any action was made relative to remote-starting (either attempting to enter reserve mode with engine running or after attempting remote-start).

0

2012 Chrysler 300 will not recognize Fob without the battery installed in Fob

I cannot get past step 9 in programming my EVO because my 2012 Chrysler 300 will not recognize my fob without the battery installed. How can I get this resolved?

0

temperature

Hello I live in a very hot country, and the temperature inside the car cabin in the summer reaches 70 degrees Celsius. Does the remote control device withstand high temperatures or is it at risk of explosion?

0

Evo-one & Evostart2 for 2022 Toyota Corolla sedan push start

Please help I did master reset Evo-one on 2022 Toyota sedan push start and did key transfer Dcrypter when put 3 times lock my car start but when using Evostart2 app i get green light flashing then orange light come one but Evo-one not get signal car not start. i just have a question do i need to program evo-one & evostart2 in the car together then return to PC do key transfer Dcrypter, because i did program only Evo-one in the car the return to PC do key transfer after that try 3 times lock it work then program Evostart2 after but doesn't work try do reset Evostar2 & reprogram again still doesn't work. Evo-one SN: 002B04 248953 Thank you very much.

0

Module not compatible with flashlink

I have purchased a EVO-ALL Module and When trying to connect to program it says module is not compatible. Can this be added to the database if not already there?

Flashlink has firmware version: 4.51-1.1.15

Module is 10/2021 SN:001A07 304791

0

Do you have an install guide for my 2010 Audi A6 AudT1 system I purchased?

Do you have an install guide for my 2010 Audi A6 AudT1 system I purchased? Youtube only has a 2015 Q5 or a 2010 A3 video someone put up but not sure it applies to my 2010 A6. Clear written instructions would be nice like the MPC kit provided for my Silverado. That had full clear instruction with pictures even.

0

Reset please

Please reset evo one SN: 002B04 248953 Thank you.

0

Please help key transfer reached limit

I try so many times and want my car it start then did master reset unit after return to Pc do Dcryptor and get limit has been reached can you reset Please. Evo one SN: 002B04 248953 Thank you very much.

0

How do I increase my remote start run time?

Hello. I have a Mazda CX-9 2023 using Evo-One to remote start. The serial number is 002B04 215450. It's installed using THAR-ONE-MAZ3 - T-HARNESS. I would like to increase the run time to the maximum after I remote start the vehicle. How can I do that please? If the decryptor needs to be used, please reset it for me please. I may have reached the limit. Thanks

0

Evo-one with Oem remote

Hi Sir Please help 2022 Toyota Sedan push Start Evo one is connected by THAR-TOY13 for Toyota programmed in car & did key transfer Dcryptor. Evo one has been update. everything was done right, but the cardoes not start remotely.when press the lock 3 times no led light on and yellow loop has been cut. Evo-one SN: 002B04 248953 Thank you very much