English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

15/03/2024

 Acura Son Vo (130Pts.)

0

please reset flash limit on my evo-one

Evo-One S/N 002B04 252778
Connectez-vous pour répondre Voir 1 réponse(s)

09/10/2023

 Acura mariser (130Pts.)

0

2018 Acura MDX EVO-ONE + T-Harness w/ take over

Have such problem’s: 1) Almost always (7/10 remote starts) after successful remote start have keyless access system indicator after press and release the Push-to-Start button once 2) and I think as a continuation’s of the 1st problem do not work multi-view rear camera (also 360 view) and blind spot system. When I turn on reverse gear I dot alarm on display: rear view camera do not work when engine do not start. So only stop and start engine again fix it. Please advise
Connectez-vous pour répondre Voir 1 réponse(s)

01/07/2023

 Acura Gary Vongsamphanh (130Pts.)

0

'10 MDX EVO-ONE w/ RFK942 remote not working, no green led lock/unlock/start

I've installed the EVO-ONE & harness w/ RFK942 remote kit on my wifes 2010 Acura MDX and it has been working fine for about 3 years till now. My wifes tried to remote start and car was not on when she walked to it, and she tried to unlock using the 942 remote and it didn't unlock for her nor any other buttons did not work. Used her oem remote to unlock and locks fine but alarm goes off when opening door due to how it's programmed but eventually she got it to disarm. To troubleshoot, I've tried pressing all buttons and all lights the blue led for button press confirmation but did not light a green led for confirmation of communication to main brain like it usually do. Checked if remote buttons is disabled (trunk>lock+trunk) but remote with just blink rapidly for a second and no leds on. Check if in valet mode and it was not as the led was not constant lit on antenna. Then I've reprogrammed the remotes (2nd remote probabaly just need new battery but if i press 2 buttons a second apart the 2nd press will not confirm blue led press and remote will not light any leds when any buttons are press for about 5-10 seconds and will not program). None of the above did not fix issues. I am seeking solutions before I dig into the dash to reprogram the brain. Thoughts?
Connectez-vous pour répondre Voir 1 réponse(s)

16/02/2023

 Acura Keith Fogah (130Pts.)

0

Please reset the flash limit on my EVO-ALL Serial# 001A06471376

Please reset the flash limit on my EVO-ALL Serial# 001A06471376
Connectez-vous pour répondre Voir 1 réponse(s)

13/11/2022

 Acura Minh tran (130Pts.)

0

No PTS output from evo

16 RDX. Car goes through starting sequence but no crank due to no pts output from evo. If I press pts manually at the normal point rs would crank car starts right up.
Connectez-vous pour répondre Voir 1 réponse(s)

23/01/2022

 Acura nader dana (280Pts.)

0

Difficulty in programming EVO-one for Acura RL 2010

Firmware is updated to 73.[38] . When I insert the 6 pin connector the red light does not become solid for me to release the programming button. It keeps alternating the blue ,red, yellow and blue&red and I have done disconnecting and redone step one many times with no result.How can I fix it?
Connectez-vous pour répondre Voir 1 réponse(s)

15/01/2022

 Acura Christopher Plank (130Pts.)

0

2011 Acura MDX Help....

I installed two of these on my vehicles in the past and everything worked flawlessly. I love this product. However, today I installed this on my coworkers 2011 MDX (Acura) regular key, evo all, with T-Harness. I made all the connections as per the instructions. The hardest part was getting steering wheel column plastic off. HAHA I pressed the button and plugged in the 6 pin connector and it just continues to flash thru the colors. It never turns red like the instructions say. I did a trouble shooting form on the website and it says the firmware is out of date. So I just bought a flash link updater. Is there anything I missed?? Are there any hints to let me know about for the updater when I get it? THANKS
Connectez-vous pour répondre Voir 0 réponse(s)

14/01/2022

 Acura nader dana (280Pts.)

0

which model fit as remote starter for Acura RL 2010?

Hi As the info on your website, EVO-ONE and EVO-ALL fit ACURA RL 2010 but I prefer EVO-ALL becuse it is cheaper.So please let me know if it is fully functionl as remote starter with orginal fobkey of car (x3 lock). Thank you Nader Dana
Connectez-vous pour répondre Voir 1 réponse(s)

19/12/2021

 Acura akmal wahid (130Pts.)

0

evo one compatible with 2001 mdx ?

Fortin EVO-ONE EVO-ONE All-in-One Remote Start, Security & Data Interface compatiblity with acura mdx 2001

Connectez-vous pour répondre Voir 2 réponse(s)

14/12/2021

 Acura Armend19 (160Pts.)

0

Alarm going off when I turn off car, Acura RL

I'm using evo-one and a omega OLRF42SST Omegalink 2-way remote, I have a 2005 Acura RL. The alarm is going off whenever I use the remote start the car and then when I turn off the car, the alarm goes off.
Connectez-vous pour répondre Voir 1 réponse(s)

13/12/2021

 Acura Armend19 (160Pts.)

0

Flashing key on dash Acura RL

Hello, I'm using evo-one and a omega OLRF42SST Omegalink 2-way remote, I have a 2005 Acura RL. The car starts fine, however, the key light on the dash is flashing whenever I use the remote start. It does not flash if I don't use remote start. Any help is appreciated.
Connectez-vous pour répondre Voir 1 réponse(s)

22/11/2021

 Acura peter bowers (130Pts.)

0

remote start no longer functioning, 2013 MDX

2013 MDX auto with navigation option. installed in 2018, REV 20180406,guide #57711. bypass firmware version 73.(26), program remote starater version 38.2, program bypass option C1 The unit was installed in 2018 and had worked fine through winter 2020/2021. With the cold weather of fall 202, tried to use the unit and get no repsonse. recently completed key bypass programming procedure and got to the end and all seemed fine. i have been using the factory remote and the 3x lock feature to operate the remote starter. the hood pin has never been installed. The yellow wire for auto trans is cut. 1x lock-car locks and blue light flashes on module-parking lights flash 2x lock-car locks again and beeper sounds, blue light flashes on module and parking lights flash 3x lock, car locks again and beeper sounds again, blue lights flashes on module, parking lights flash-then the parking lights flash 1 additional time no remote start. Please provide some guidance, thank you.
Connectez-vous pour répondre Voir 1 réponse(s)

12/10/2021

 Acura Yuvrajh Singh (210Pts.)

0

Evo one does not enter program mode to program telematics unit.

2020 rdx push to start. Nothing happens after holding the button for 5 sec with ignition on.
Connectez-vous pour répondre Voir 1 réponse(s)

16/05/2021

 Acura Luis Sanchez2 (950Pts.)

0

RFK942 not working after disconnecting and reconnecting the car battery

After getting the RFK942 working I did some maintenance on the car. I disconnected the battery to perform the maintenance required and after reconnecting the battery I attempted to lock the doors with the RFK942 remote. The remote sent the signal but doors did not lock (LED turned red). I thought that perhaps the antenna needed to be reprogrammed so I attempted to perform the programming procedure again. The antenna would not program (no blue LED) so I connected it to the Flashlink Manager to see if something had been turned off. The Flashlink Manager did not recognized that the antenna was connected. From this I am gathering that the antenna was damaged when I reconnected the car battery. Is this possible? If so, what can I do to prevent this from happening again? Would a different RF kit work better (for example the RF642W)?
Connectez-vous pour répondre Voir 1 réponse(s)

06/04/2021

 Acura Luis Sanchez2 (950Pts.)

0

EVO ONE does not see RFK942

Good day to you. I am having problems programming the RFK942 to the EVO ONE (installed in my 2010 Acura TL with Push-to-Start). When I connected the antenna to the module (using only the antenna cable the RF kit came with) the blue LED on the RF antenna never turned on. After several attempts, I decided to remove the EVO ONE and connect it to my computer (running Windows 10) using the Flashlink Updater (running the latest firmware). The Flashlink Updater could not detect the EVO ONE (and the EVO ONE LEDs never illuminated). I thought that perhaps the Flashlink Updater was inoperative but when I connected an EVO ALL and two RFK942s to the Updater, I discovered that the Updater is functioning properly. I just programmed the EVO ONE a week ago and had no issues then. In fact, the module remote starts the vehicle (Lock 3x on OEM key fob). Any help would be greatly appreciated.
Connectez-vous pour répondre Voir 1 réponse(s)

30/03/2021

 Acura Luis Sanchez2 (950Pts.)

0

RF Kit Acura TL

I am installin the RFK942 to my 2010 Acura TL.  Will there be any additional wires that will need to be connected at or to my EVO ONE (besides the cable from the antenna)?  Are there any features that need to be turned on on the Flashlink Updater and if so, where will they be found?  Thank you.

Connectez-vous pour répondre Voir 1 réponse(s)

28/03/2021

 Acura Luis Sanchez2 (950Pts.)

0

Check Keyless Message

The installation and programming of the EVO ONE on the 2010 Acura TL (Push to Start) went well. I am able to start the vehicle, and, as expected, the engine shuts off when the door is opened (which is a bummer). My question concerns a message on the instrument panel. When I remote start the vehicle the "Check Keyless Starting System" (with an amber key with an exclamation point) is displayed. Is this normal? My second question iis about adding an RF kit. Will the RFK942 RF kit work with the EVO ONE on this car? Thank you in advance for your help.
Connectez-vous pour répondre Voir 1 réponse(s)

23/03/2021

 Acura Luis Sanchez2 (950Pts.)

0

2010 Acura TL Push Start Evo One will not program

While installing the EVO One to my 2010 Acura TL (with Push-to-Start) I found that several of the wire colors called out by the installation (REV:20191022, Guide 19411) and the Wire Color guide did not match what the car has (on gray 32 pin connector and blue 36 pin connector).  I proceeded by connecting at the specified locations shown on the diagram.  Once the connections were completed, I attempted to program the module (which was updated and programmed with the Flash Link Updater).  Step 1-4 went OK, however, when I got to step 5 (Do not press the brake pedal.  Press the Push-to- Start button twice to turn on the ignition--  The RED LED will flash rapidly 10x times. -- Key bypass programmed. --The BLUE LED will flash rapidly. --CAN-Bus programmed.), the red LED extinguished and I could not complete the programming.  I tried this several time with the same results.  Your help with this issue will be greatly appreciated.

Connectez-vous pour répondre Voir 1 réponse(s)

08/03/2021

 Acura Minh Ta (130Pts.)

0

Evo-One Limit Reached Acura

Hi, My Dcryptor Limit Has Been Reached for a 2014 MDX. Can I have It Reset, Thanks S/N: 002B07124891
Connectez-vous pour répondre Voir 1 réponse(s)

17/02/2021

 Acura phap truong (250Pts.)

0

How do I get my Drone Mobile to work with my EVO ONE in my 2011 MDX?

I've loaded 0.50 with flashlink updater, but it's still not communicating with the EVO One.
Connectez-vous pour répondre Voir 1 réponse(s)

13/02/2021

 Acura Nathaniel Lowery (130Pts.)

0

Start works, but remote stop does not.

Remote start works on 2018 Acura TLX, but 3x lock button doesn't stop the car. I tried waiting over a minute, but can only stop the car by opening the door.
Connectez-vous pour répondre Voir 1 réponse(s)

31/01/2021

 Acura skylinewindowtinting (600Pts.)

0

ACURA 2016 TLX now has trouble starting

I installed a evo one remote starter in a 2016 Acura TLX.I used a THAR-HON 4  REV.3 T-harness. is this the correct t-harness?. Everything thing went fine with installation and with the programming also. Now if you try to start in the regular way with the push button. It doesn't want to start every time.

after like the third or fourth attempt it starts. I can't figure out why this is taking place. 
also I added the CARLINK MOBILE also works fine.

SERVICE # 002B04072902
 

Connectez-vous pour répondre Voir 1 réponse(s)

29/12/2020

 Acura P Patel (280Pts.)

0

2011 Acura RDX Base 4cyl Turbo Gas Automatic Regular key Remote car start

2011 Acura RDX Base automatic with factory installed keyless door entr and Regular Key start.    1. Will EVO-One remote car start work ?    2. What Harness do we need to oder with EVO-ONE?   3. Appreciate link to Installtion video for this vehicle?
Connectez-vous pour répondre Voir 1 réponse(s)

17/12/2020

 Acura Александр Иванов2 (130Pts.)

0

My dcryptor's limit has been reached for this car

My dcryptor's limit has been reached for this car. Please help EVO-ONE S/N: 002B04 063541
Connectez-vous pour répondre Voir 0 réponse(s)

13/12/2020

 Acura Darren Martin2 (130Pts.)

0

Immobilizer wire color and pin location do not match diagram downloaded from fortin website.

SL3 - 2010 Acura TL 3.7 - Standard key
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer