English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

04/01/2024

 Nissan Justin Lundy (130Pts.)

0

Stuck on Step 4

2012 Nissan Rogue Intelli-key using T harness NIS 2. I cannot get passed step 4. The yellow light never flashes it doesn't change at all after pushing button any amount of times. I went through the troubleshooting guide and I don't have power on yellow wire, I also reversed the can-bus wires which didn't help. The fob was placed 40 feet away inside the house next to the spare keys we have for this vehicle.
Connectez-vous pour répondre Voir 1 réponse(s)

30/12/2023

 Chrysler Amin Bakri (210Pts.)

0

programming

intalling EVO CH5 on my 2009 Chrysler Sebring. When i go to progam it to the vehicle i press the black button and plug the black connector with igition off. All 3 LEDs flash at the same time and will not go to just blue like it says it is supposed to program. I cant find the trouble shooting section to find answers
Connectez-vous pour répondre Voir 1 réponse(s)

28/02/2023

 Nissan Jeff Whaley (220Pts.)

0

programming issues s/n 002B04273087

once decripted, all i get is a solid amber light when reinstalled and the key is on. unit will not let me into any typeof programming. no remote or function. I have no conformation from the antanna or parking lights. it will however make the interior lights blink once i have started it with the key and i push on the brake. I am using the nis2 T harmess and the rf remotes.
Connectez-vous pour répondre Voir 1 réponse(s)

18/01/2023

 Ford Todd Lusby (130Pts.)

0

2010 ford escape KEY-OVERRIDE-ALL

I'm installling the KEY-OVERRIDE-ALL with a DEI remote start. When I attempted to program prior, I would see the LED start flashing, but programming didn't complete. Now when I attempt to program, the LED on the module stays on and the security light on the dash flashes rapidly. I've confirmed I have 12V on Red, Ground on Black, Ignition on Yellow, and remote start staus on Blue. Is there anything else i should try on this module? The module was purchased new in December and hasn't been installed in another vehicle.
Connectez-vous pour répondre Voir 1 réponse(s)

10/01/2023

 Kia n h (230Pts.)

1

Why won't my Evo-One move past step 4 on programming?

I have verified the correct firmware, proper voltage on yellow wire A1, and correct can-bus wiring.I have constant 12v with a good ground. When I turn the ignition to run the blue led that is supposed to flash 10x's turns off. I installed accordind to the install guide provided through fortin's website.I have followed the troubleshooting guide and get stuck after confirming all 5  steps

The first 3 steps in the programming are very straight forward. If you cannot pass these steps verify the following:
1- Firmware: Ensure you have flashed the correct firmware to the module as indicated in the installation guide.
2- Power & Ground: Verify the module is receiving a constant 12 volts and has a good ground.
3- Yellow Wire (A1): Verify this wire is on the correct ignition wire. Their should be 0 Volts present during the first 3 steps.

If the Blue led does not flash common issues would be the following:

1- Yellow wire (A1): Not connected to correct ignition source.
2- Can Bus Wires: If these are reversed or connected to the wrong can bus wires the module will not program.

Connectez-vous pour répondre Voir 1 réponse(s)

26/12/2022

 Ford Ryan Andersen (130Pts.)

0

2017 Ford Focus Programming Issues

I am having some difficulty programming my EVO-All FORT4 with my 2017 Ford Focus. The T-Harness is all hooked up, and the device has been flashed with the correct module. When I attempt to pregrade both keys, nothing happens when I press the program key at the end of the sequence. When I attempt to program a single key, it doesn't change from red to yellow. Any and all help would greatly appreciated.
Connectez-vous pour répondre Voir 1 réponse(s)

19/12/2022

 Volkswagen Ryan Mcpheron (160Pts.)

0

During programming on step 14 guide 65601 only redlight flashes not red and yellow

It flashes 5 times
Connectez-vous pour répondre Voir 1 réponse(s)

25/08/2022

 Ford Joe Allison (220Pts.)

0

2017 EvoOne with TharFor3 T harness, blue light won't blink on programming

Thank you in advance for any help! I am a long time using of the EVO ALL and have done a few EVO ONE. A bit stumped on my 2017 F150 though. Using EVO ONE with the THAR FOR 3 harness. All plugged in. Following wiring diagram for the A1 and A16 (put them together) on the white 20 pin connector. When I go to program it, I can't get it to "blink blue". Therefore, I can't get any further in the programming procedure. Followed the directions in the Guide. What could I be missing? Joe
Connectez-vous pour répondre Voir 1 réponse(s)

18/08/2022

 Ford jaber awadh (340Pts.)

0

F150 2012 programming

I have a f150 2012 i done every thing 100% In the programing phase I made every thing i enter the first key after the second key and after the first key then the blue and red started flashing after that only the blue led appeared and the still on without the key but if i unplugged the red connector the car turn off please can you help me in the programing
Connectez-vous pour répondre Voir 2 réponse(s)

19/07/2022

 Ram Tim Mitchell (130Pts.)

0

EVO-All won't pass Red Light on programming (Step 5)

I've flashed the EVO-All multiple times using both the wizard and Pro versions of the flashlink. No success. I essentially flash the module and it won't program past step 5 where the red light is supposed to turn blue and flash. No clue where to go from here. I'm using the T-Harness as well so there's no direct wiring.
Connectez-vous pour répondre Voir 1 réponse(s)

13/02/2022

 Toyota Mitchell ignatius (250Pts.)

0

Programming 2012 fj cruiser solod red light

I have everything properly wired for the 2012 fj cruiser and I programmed the module on the computer. When It comes to plugging in the module the light is solid red like it's supposed to be but when you turn the key to the on position it just stays solid red. Maybe someone can reboot my module with the s/n?
Connectez-vous pour répondre Voir 2 réponse(s)

31/12/2021

 Toyota Mitchell ignatius (250Pts.)

0

2012 fj cruiser programming

I have everything wired correctly with the harness. I plug module in light stays red like it's supposed to but when I put the key to the run position it stays solid red and doesn't flash like it's supposed to
Connectez-vous pour répondre Voir 1 réponse(s)

27/12/2021

 Ford ryk (220Pts.)

0

2011 Ford Escape red light stays on during programming - SOLVED

Vehicle: 2011 Ford Escape

Evo All #001A07260304 installed with T-harness THAR-FORD4; plug-n-play install, teed connections to ignition switch, immobilizer antenna and OBDII connector; no wires spliced

Can't get the unit to program.  Process: Hold program button, plug in data cable and release on red light.  Insert key and turn on until theft light turns out.  Remove first key and insert second.  Turn on for 3 seconds, theft light goes out, turn off and remove.  Last step says to press and release programming button within 5 seconds (this is where it gets stuck).  Red light should flash 10 times and blue light should flash 10 times and ignition comes on and turns off again.  When I press the button the last time, the red light blinks and just stays on.

I've tried the firmware downgrade listed in https://fortin.ca/en/qa/92073/faq-red-led-stuck-on .  That link says to downgrade to v 0.99 but the lowest version for Ford appears to be 4.01.  I flashed 4.01, power cycled in vehicle, reflashed v 71.52, unlocked settings and reset the unit.  Still same results.

I've also tried testing the data bus.  Hold button, insert data link connector, release button on blue light.  Connected all other connections and turned key on.  Blue light stays solid.  Shouldn't it flash on data?

The yellow wire is not connected as it seems to be part of the T harness, but I've tested it for 12v on ignition and it is getting it.  I don't have the valet switch or hood pin switch connected.  What am I missing?  I'm wearing out the plugs with all these connections/disconnections.

 

 

 

Connectez-vous pour répondre Voir 1 réponse(s)

18/12/2021

 Ford Corey Wilson (130Pts.)

0

Red light stays on during programming and wont program the keys

I hVE 2008 Ford Escape. I installed the Evo all fort4 with the the t-harness. I have installed all connectors(1,2,3) and connected a relay to the lights as instructed in step 4. I plugged the black connector in while holding the button in and then let it go when the red light came on. I put in each key for 3 seconds each and then pushed the button in. It didn't start the vehicle. Red light stayed on teh whole time. It only blinked when I pushed the button in. What causes this and how can I fix it?
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer