Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

when i activate the remote start it flashes blue 5 times.

i just bought a mitsubishi lancer and it has the fortin ftx84 remote start put into it, when i activate the command start it flashes blue 5 times, i have read that this is the hood latch. how can i fix or figure out what the issue is with the hood latch?

0

When i try to remote start after install a blue light flashes on module but Jeep does not start

I finished installing and programming my remote start on my 2020 Jeep Wrangler w/o keyless entry. I have the after market remote start remotes and when I go to start it a blue light flashes once on the module but the Jeep does not start. Dash screen light comes on and so does the lights by the gear selector but that’s it.

0

Evo one CHR4 dodge challenger 2010 no any action only security light flashing

2010 Dodge challenger SRT with stander key and manual transmition Module programming okay blue light flash every press lock Remote start red light one and give 2 sound then off dashboard securty light flashing Evo one with Chr 4 T-Harness please help

10/01/2023

Kia n h (230Pts.)

1

Why won't my Evo-One move past step 4 on programming?

I have verified the correct firmware, proper voltage on yellow wire A1, and correct can-bus wiring.I have constant 12v with a good ground. When I turn the ignition to run the blue led that is supposed to flash 10x's turns off. I installed accordind to the install guide provided through fortin's website.I have followed the troubleshooting guide and get stuck after confirming all 5  steps

The first 3 steps in the programming are very straight forward. If you cannot pass these steps verify the following:
1- Firmware: Ensure you have flashed the correct firmware to the module as indicated in the installation guide.
2- Power & Ground: Verify the module is receiving a constant 12 volts and has a good ground.
3- Yellow Wire (A1): Verify this wire is on the correct ignition wire. Their should be 0 Volts present during the first 3 steps.

If the Blue led does not flash common issues would be the following:

1- Yellow wire (A1): Not connected to correct ignition source.
2- Can Bus Wires: If these are reversed or connected to the wrong can bus wires the module will not program.

0

2014 Jetta The doors don't open.

I installed Evo-All on a 2014 Jetta (standalone).   001A07363467. By pressing 3 times, the engine starts, but the factory remote control does not close the door or open it. It extinguishes by extinguishing, but the pauses between presses should not be less than 2 seconds. The blue LED flashes erratically between presses.

0

2016 Hyundai Accent. No immobilizer. Cannot make blue light flash for can programming

I have a 2016 Hyundai accent. Have the Can wires hooked up as shown in diagram. Grey wire is reading 3.18 VDC and Grey and black is reading 2.48VDC. Plug in wires and turn ignition to on/run position and the blue light does not flash. I am using thar-khy2 T-Harness. A1 is hooked up to E5 like in diagram. Help......

20/12/2022

Audi Vincc (230Pts.)

0

Can't complete Step 5 - Blue LED don't Flash. Audi S4 2014

Anyone can help me? I'm Stuck on Step 5 while programming my EVO-ALL with the T-Harness EVO-AUDT1 on My Audi S4 B8 (2014). The BLUE LED doesn't begin flashing. CAN Connections are Good. I Measure round about 3V on the Whit 5 Pin connector between Grey and Grey-Black. Grey-Black goes to Orange-Brown (CAN-Low) and Grey goes to Orange-Green (CAN-High) like in the Guide described. I have connected these Cables at the CAN Connector near the Relays at the left bottom under the Driver footwell. S/N: 001A06905491 Thanks!

1

How to get past decryptor programming?

Ive tried taking the battery out and everything it says but it stays on blue. is there anything that could be causing this? did i not hook something up that i needed to? i have a 2016 mazda 3 push to start automatic, using the evo-all with the MAZ-1 t-harness that came with it. installation instructions were not very clear. please help.

0

EVO-All won't pass Red Light on programming (Step 5)

I've flashed the EVO-All multiple times using both the wizard and Pro versions of the flashlink. No success. I essentially flash the module and it won't program past step 5 where the red light is supposed to turn blue and flash. No clue where to go from here. I'm using the T-Harness as well so there's no direct wiring.

0

Everything is plugged in but LED will not flash rapidly in step 5

Toyota 2016 Prius TOYT6 T harness I am using the guide : Regular Installation without Take Over with T-harness Hello, I spliced into the 3 wires that were needed. 2 at the OBD2 connector (ground(4) and +12V(16) and 1 wire at the hybrid ECU connector (+) starter(A16). I took out the 30 pin main body ECU and plugged in the 30 pin connector labelled B from the T harness into it. I then plugged in the 30 pin main body ECU into the T harness female 30 pin side. Am I missing anything? I plug in the power wire into the Fortin module while holding the button and I waited until it turned solid blue. I then connected the rest of the connectors into the Fortin module. I pressed the power button on the vehicle twice without pressing on the brake. The blue LED stays solid and does not flash. When I turn on the car fully, the LED blue light still stays on. If I turn off the car, the blue LED light is still on

0

Blue light won't flash in step 5 in guide 65321

Hi On my 2012 vw jetta manual transmission push to start. I connected everything it told me to connect on the wiring diagram but when I turn the ignition on the blue light turns of but won't flash Please help

0

I can not get the blue light to flash on the module on the first step of programming

09/01/2022

Chrysler