English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

20/12/2022

 Audi Vincc (230Pts.)

0

Can't complete Step 5 - Blue LED don't Flash. Audi S4 2014

Anyone can help me? I'm Stuck on Step 5 while programming my EVO-ALL with the T-Harness EVO-AUDT1 on My Audi S4 B8 (2014). The BLUE LED doesn't begin flashing. CAN Connections are Good. I Measure round about 3V on the Whit 5 Pin connector between Grey and Grey-Black. Grey-Black goes to Orange-Brown (CAN-Low) and Grey goes to Orange-Green (CAN-High) like in the Guide described. I have connected these Cables at the CAN Connector near the Relays at the left bottom under the Driver footwell. S/N: 001A06905491 Thanks!
Connectez-vous pour répondre Voir 1 réponse(s)

05/03/2020

 Audi Stuart Pullen (190Pts.)

0

2009 S4 MANUAL TRANS, NO START AFTER 3X LOCK

Hello, I have a manual trans Audi s4 2009 keyport Evo One , i have installed the T-harness - yellow line from 6 pin to the clutch bypass (red/blk) in engine bay as per pics, Canbus High and Low installed correctly and the Pink from the 6 pin to the purple/ yellow to convenient ignition out. I have the module programmed as per intructions and no error. when connect all the plugs and lock the car then try 3x lock to RS nothing happens. I see the module flash with a blue led at every lock and unlock but no ignition. Evo One S/N 002B04 013291 Thank you in advance! Stu.
Connectez-vous pour répondre Voir 1 réponse(s)

02/02/2020

 Audi Ken Pickering (130Pts.)

0

Evo-AUDT1 Step 5 progmg, Blue light won't switch from solid?

I have installed the EVO-AUDT1 as per the I struxtions. Connections are good. When try programming the key learn I can not get the blue light to go out. No. Responsive to the program button push. Also, when I stalled in non programming state all thrre lights flash together. I am under the impression this is pre programed ready to go so I didn't buy the flash link programmer. Do I need to flash this unit?
Connectez-vous pour répondre Voir 1 réponse(s)

15/10/2019

 Audi BRENDAN DONATELLA (200Pts.)

0

Evo-One wont go into Program Mode Audi A4

Directions say to hold the button down and plug in the red cable/black connector, and the light should turn blue. However my light is always red, will not turn blue or flash any other colors. What am i doing wrong? I am driving a 2014 Audi A4. According to the directions i should be able to enter programming mode without even being connected to my car, just the PC.
Connectez-vous pour répondre Voir 1 réponse(s)

03/06/2019

 Audi Nathan Crim (180Pts.)

0

2009 Audi s5 manual evo-one with thar-audi blue led stays solid will not program

2009 Audi s5 manual transmission, keyport and start/stop button with evo-one with thar-audi t harness. The blue led stays solid when the ignition is turned on with the keyport and I am unable to program. I have checked the yellow starter wire connection to the clutch bybass and the connection seems solid. The 12v to the juction box is getting a reading and good. The can high and low are also connected good. The connection for the vehicle is clipped together and the plug for the evo-one is connected as well. The 16pin is also plugged into the keyport. When I plug the data cable in while holding the program button the led turns blue. I plug in all the other cables, insert the key, and press once WITHOUT pressing the brake. When I press and release the the program button the blue led remains on as if nothing has happened. Any help please?
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer