English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

15/12/2023

 Jeep Downsie23 (130Pts.)

0

When i try to remote start after install a blue light flashes on module but Jeep does not start

I finished installing and programming my remote start on my 2020 Jeep Wrangler w/o keyless entry. I have the after market remote start remotes and when I go to start it a blue light flashes once on the module but the Jeep does not start. Dash screen light comes on and so does the lights by the gear selector but that’s it.
Connectez-vous pour répondre Voir 1 réponse(s)

20/01/2023

 Volkswagen Tony Mercede (160Pts.)

0

NO FLASHING BLUE LIGHT AT STAGE 5

2014 VOLKSWAGON JETTA TDI AUTOMATIC TRANS AFTER REPROGRAMMING EVO ONE 3 TIMES STILL CANT GET THE EVO ONE BLUE LIGHT TO FLASH AFTER TURNING ON IGNITION, BLUE STAYS LIT THEN WHEN IGNITION IS ON LIGHT GOES OUT UNTILL YOU TURN IGNITION BACK OFF THEN BLUE LIGHT COMES BACK ON? FORTIN EVO-ONE W/ VWT1 T HARNESS DATE 12/2021 s/n 002b04 248922 firmware remote start = 1.[26] hardware 7.0 BYPASS = 75.[41] hardware 4.0 loaded suggested options on both with diesel option checked
Connectez-vous pour répondre Voir 1 réponse(s)

18/12/2022

 Chevrolet SAMANTHA ROOP (130Pts.)

0

Evo all stand-alone 07 Equinox blue light turns off as soon as I plug in the white connector

Guide #59161 module key bypass programming can not go past step 3 blue light will stay on until I plug in the white connector. I have verified there is no voltage on the ignition yellow (A1) wire when ignition is off. Any help is appreciated thank you
Connectez-vous pour répondre Voir 1 réponse(s)

12/12/2022

 Buick Eric McClish (130Pts.)

0

evo-gmt1 no red light no start

2011 buick regal evo-gmt1 sn001A07v253955 . Blue light flashes with door lock / unlock . oem remotes. no red light , no start. thar-gm1 rev2 harness. what is the correct wiring diagram ? at the moment brown wire to can sw pin 1. brown with white stripe to green /gray parking lights . cannot get ahold of tech
Connectez-vous pour répondre Voir 1 réponse(s)

05/06/2022

 Infiniti Charles Ong (130Pts.)

0

Red light disappears and Blue light stays solid

Hello, I have a 2015 Infiniti Q70 and when i program the module, I can get up to step 8 without any issues. When I press the brake for the second time, the red and blue light comes on, but after about 1 second, the red light disappears and the blue light stays solid. I'm unable to complete the programming of the module. Verified all connections are tight and correct. Please help!
Connectez-vous pour répondre Voir 1 réponse(s)

05/02/2022

 Nissan Domenick Desimone (130Pts.)

0

I can not get the blue light to flash on the module on the first step of programming

2013 nissan pathfinder 2013 nissan pathfinder
Connectez-vous pour répondre Voir 1 réponse(s)

11/02/2021

 Chevrolet marcus madden (220Pts.)

0

How to add a blue flashing light for when system is armed?

I want to add a flashing blue light to warn off vehicle burglar. I tried you white wire on evo all, but it's a staying a ground with car running or off.
Connectez-vous pour répondre Voir 1 réponse(s)

01/02/2020

 Ford Todd Aker (200Pts.)

1

Can not get past step 6 no blue light in step 7

I have a 2010 ford escape. auto trans and 6cyl engine. I can not get the blue light to light for step 7. Checked all the can connections and even solidered them. they are correct as the instructions ask them to be. HELP?
Connectez-vous pour répondre Voir 2 réponse(s)

01/02/2020

 Ford Todd Aker (200Pts.)

1

Can not get past step 6 no blue light in step 7

I have a 2010 ford escape. auto trans and 6cyl engine. I can not get the blue light to light for step 7. Checked all the can connections and even solidered them. they are correct as the instructions ask them to be. HELP?
Connectez-vous pour répondre Voir 2 réponse(s)

14/10/2020

 Ram Joshua Joyce (140Pts.)

0

Blue light never flashes

I have a 2020 ram 1500, tip key , gas model truck. When following the directions I get to step 7 which is where I get the red and blue lights when inserting the key but then my red light goes off where it should stay on and the next step completely fails as the blue light just goes out and does not flash when it should. Anyone have the answer to this issue or is there another wire that needs to be hooked up other than my 2 can high and low and yellow to ign?
Connectez-vous pour répondre Voir 1 réponse(s)

23/02/2020

 Ram mike S (130Pts.)

0

Module appears to pass dcryptor, but still slow flashes blue when installed.

After returning module to truck after Dcryptor processs completes, the module still slow flashes blue when installed. The truck still starts with the key, remotely locks and unlocks, but will not remote start. The module does nothing but slow flash blue. I don't see anything in the instructions or troubleshooting about this problem.
Connectez-vous pour répondre Voir 1 réponse(s)

01/02/2020

 Ford Todd Aker (200Pts.)

0

Can not get past step 6 no blue light in step 7

I have a 2010 ford escape. auto trans and 6cyl engine. I can not get the blue light to light for step 7. Checked all the can connections and even solidered them. they are correct as the instructions ask them to be. HELP?
Connectez-vous pour répondre Voir 0 réponse(s)

11/01/2020

 Mazda Alex Macharia (130Pts.)

0

Mazda Failing Decryption process (not able to get a solid blue)

I have tried to run the exact process for initializing decryptor for a CX-9 install, starting with diconnecting the neg battery terminal and then connecting the steering wheel white terminals into the T harness,reconnecting battery power and then holding down the button on the Evo one module while plugging in the 6 pin connector. I have not been able to get the module to set the blue solid light. Anyone run into this? Module was programmed correctly via flashlink
Connectez-vous pour répondre Voir 1 réponse(s)

22/12/2019