Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

User

Mike Evans

Joined on the:

Dec. 12, 2013

Score

1960

Comment(s)

7

Voted question(s)

0

Voted answer(s)

0

Votes up

0

Votes down

0

Votes up received

2

Votes down received

0

Recent Activity

Question(s) asked

3

Answered question(s)

19

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question
RECENT ACTIVITY QUESTION(S) ASKED ANSWERED QUESTION(S) COMMENTED QUESTION(S)

09/11/2019

 Nissan Micheal Unger (2680Pts.)

0

2018 Nissan sentra pts no HVAC

Installed a Solace remote starter and evo-nist1, standard install, into a 2018 Nissan Sentra PTS, auto. First problem i overcame was that the NIS1 T harness was made incorrectly, getting power from obd connector instead of brake switch, would only have power with key on. Redirected 12v source from brake switch. Programmed great, starts and seemed ok. Let vehicle sit for about 5 mins or longer, try to remote start, starts ok but HVAC unit is off, have to physically turn the unit back on by pushing buttons on the hvac panel (has auto hvac system). I tried reprogramming evo- all, reloading the previous firmware level, reprogramming again, replacing evo, still no change. Any help would be greatly appreciated. Serial# 001A07 055068
Login to reply View 1 answer(s)

12/10/2019

 Nissan aaron boone (130Pts.)

0

Where is another location for the transponder connector wires?

2016 vera note standard key. I dont have the transponder connector in the location it says. Has one thick black cable in that location. Is there another spot to get the rx and tx wires? Thanks.
Login to reply View 3 answer(s)

26/08/2019

 Nissan Robb Millett (250Pts.)

0

2017 Nissan Altima check engine code P0462

I installed the Evo-All and everyting works correctly but my check engine light is on. I went and had it checked and it is throwing a code of P0462. Open circuit low input poor electrical connection faulty fuel sensor. This wasn't there before i installed it. Didn't cut any wires or anything like that. Maybe bad connections or bad module? everything works and starts just fine.
Login to reply View 1 answer(s)

05/02/2017

 Honda john Adock (210Pts.)

0

Cannot manually kill engine after remote start

Honda Pilot 2014. Evo One.Thon-5 harness. Car remote starts, but no way to manually kill engine. Have to wait for Evo One timeout, which I got set at 3 minute now. TO manually kill engine, I tried: 1. pressing break pedal 2. Insert key, turn to run, press brake pedal 3. insert key, turn to run, turn to off 4. Insert key, turn to run, turn to off, press brake pedal 5. FOB, lock , unlock, etc. 6.Master rest Evo one., then enable C1, D2, 32-3, 38-2. 7. Even tried A3 - key bypass enable/disble
Login to reply View 1 answer(s)

10/01/2017

 Nissan skylinewindowtinting (600Pts.)

0

The remote start will come on and not crank. It says brake on the dash.

The program went well
Login to reply View 1 answer(s)

08/01/2017

 Nissan Mike M (9800Pts.)

0

Why do I need to give up a key for install.

Hello, I have been a long time customer of fortin and belive you guys make the best products, you are the only brand i use for bypasses. I was looking to install a remote start in a 2016 Nissan Rouge PTS and I saw that it required a key for install. Now I searched around on the internet and saw that idatalink doesnt require a key for install. http://www.idatalink.com/search/search?vehicle_make_id=31&vehicle_year_id=2016&vehicle_model_id=696&vehicle_id=20302 Now I have never used their products but was just wondering what they do different that I dont have to give up a key, or if there was a way to tweak the evo all so i dont have to give up a key. Thanks
Login to reply View 2 answer(s)

07/01/2017

 Toyota Randy Smith2 (160Pts.)

0

Why will my doors not unlock with OEM fob after remote started 2015 Toyota Tundra SR5?

2015 Toyota Tundra SR5 all conections soldered, all other features seen to work correctly. factory key fob 3x press to start When i press unlock during a remote start session ths doors do not unlock, only the pakring lights flash.
Login to reply View 1 answer(s)

02/01/2017

 Nissan Dan Archer (260Pts.)

0

Juke will not 3x or RF start start without the OEM key in the car.. plus a few other problems

EVO ALL THAR-NIS1 with RF kit FTX64-2W installed in a 2015 Nissan Juke PTS. Easy install but had a heack of a time with the flashlink. Repeatedly told me that the device was disconnected when I would select save. Updated to the latest verion and went with the bare minimum selections only selecting what was shown in the manual.. D1 C1 H2. I know that theres more to be selected but seemed that when I would select what made sense.. it didn't like it and would disconnect when saved. So as of right now it is loaded with those basic commands. The module programming itself went smooth and ended with the slow blue pulse.. went through steps twice. I failed to include the service number last week.. same question but sn is now included. So with basic commands loaded I placed it back into the car and introduced the RF transmitters and moved on to the final steps... testing. I found that the car will not remote start with the oem fob or the RF fob unless the oem fob is in the car. Also, the rf fobs will not remote lock/unlock but does flash the lights.. can't remember if oem fob was in car or not? I did connect the lock/unlock wiring which was somewhat confusing by the diaagram.. it specifies in the instructions that 12 is blue and red is 13 but if you look at the pictures you have listed, its not that at all... If you count out the pins you'll see what I mean. I went by the picture.. Lastly, it was time to call it a day and button the car up and reschedule and I noticed that the parking lights were on. I can't recall but I believe it was while the car was locked but not 100% certain. The only way to get the lights to go away was by unplugging the module.. We're going to have another shot at this later today and any help is greatly appreciated.
Login to reply View 2 answer(s)

01/01/2017

 Dodge Clarence Leavitt (340Pts.)

0

What is wire A13(Yellow/Blk) - External Input for?

Is the A13 wire required in stand alone evo all
Login to reply View 1 answer(s)

01/01/2017

 Audi G M (15380Pts.)

0

2006 AUDI A6 remote start

Happy New Year! Here it is written about xpresskit. Can I ask a question about dball2?
Login to reply View 1 answer(s)

01/01/2017

 GMC Doug Millard (130Pts.)

0

Evo GMT-4 will not program for 2008 GMC Sierra 2500 Diesel

I purchased an EVO GMT-4 for installation in a 2008 GMC Sierra SLT 2500 HD. After instalation of the unit with the T-Harness, I attempted to program the unit. I followed the directions, but after I turned he key, instead of the blue light flashing, it just turns of and stays off. I attempted the programming several times to no availl It came with: Hardware Vr. 6 Firmware Vr. 70.16 Date: 11/2016 EVO-GMTx Preloaded
Login to reply View 1 answer(s)

31/12/2016

 Jeep Matt Fielder (130Pts.)

0

Will EVO allow non-chipped keys to start Wrangler

Once programmed/installed, will the EVO-CHRT5 allow a non-chipped key to start the Jeep? Or will it only be active during remote start?
Login to reply View 1 answer(s)

31/12/2016

 FAQ Clarence Leavitt (340Pts.)

0

Bought EVO-CHRT5 for 2005 dodge dakota be stand alone remote start?

Does my truck need aftermarket remote start module?
Login to reply View 1 answer(s)

31/12/2016

 Subaru Mark Mortenson (180Pts.)

0

T Harness wire tail color wrong?

I have a THAR-SUB1 T-harness for a 16 outback auto key start. The harness has a yellow and black wire tail coming out of it and the directions show a pink for + ignition. Is this wrong?
Login to reply View 1 answer(s)

30/12/2016

 Dodge Phil Ovenden (130Pts.)

0

Blue light not flashing on Evo-chrt4 setup in 2012 dodge grand caravan

Blue light goes out but does not flash when turning on ignition. Yellow wire connected together. Directions from other troubleshooting say the bus wires are are reversed. Do I modify the t-harness to fix this problem? I have the programmer and ref lashed the unit.
Login to reply View 1 answer(s)

30/12/2016

 Nissan Mike Evans (1960Pts.)

0

What settings for Rockford fosgate autolink

I am trying to conect a Rockford fosgate autolink to my evo all in a 2015 Nissan Rogue. I have option H1 enabled per the install guide and I am using the white connector on the harness. I can't get it to communicate. Do I need to change any other settings?
Login to reply View 1 answer(s)

28/12/2016

 Ram Ricky Gragg (130Pts.)

0

2006 Dodge Ram evo-chrt5 turns ignition to run but won't start.

Service no 003606 001496. I made all the connections and followed the program procedures. When I push the lock on keys 3x the truck will unlock then lock the leds will flash on eco all then the ignition will turn on but it won't start the truck. I can hear fuel pump prime but it doesn't turn truck over. I didn't use a resistor in the parking light wire tap but I had read that it only triggers lights and doesn't effect the remote start itself. Is this a programming problem? Or maybe software? I'm using and connecting thar-chr5 harness with out the data link like wire diagram c shows. I have the omevoall can bus interface module

Login to reply View 1 answer(s)

27/12/2015

 Nissan James G. (340Pts.)

0

Lock & unlock buttons work but no remote start (Evo-All)

I just completed an install & am attempting to remote start my 2012 Nissan Rogue (base model with standard key) with the Prestige APS787E alarm and it isn't starting. I have the Forting EVO-ALL bypass hooked up along side it in D2D (data to data) mode. I can confirm that my lock, unlock & trunk buttons work perfectly on my Prestige remote but once I attempt to do a remote start, my amber parking lights flash exactly seven times.    Also when I attempt to do a remote start, I notice no lights flash on the Evo-All, is this normal?   Moreover, I didn't hook up the hood pin switch that came w/ my alarm kit. Could that be the issue? Does the Prestige require the hood pin switch to be connected for the remote start to function? WIrecolor.com said my Nissan has a hoodpin switch but I physically couldn't find one under the hood.   Thanks & happy holidays
Login to reply View 1 answer(s)

07/12/2015

 Nissan Mike Evans (1960Pts.)

2

2015 Nissan Sentra door pin issue

2015 Nissan Sentra. Having problems with the driver's door pin function. All wires are connected as per the instructions but car will not start with door closed. If I open the door is starts fine. Seems the function is working opposite as it should. Tried backing firmware to an earlier one and it still does the same. Firmware or module issue? I think all of my settings are correct.
Login to reply View 1 answer(s)

25/11/2015

 Nissan JASON SMITH (130Pts.)

0

2015 rogue pts wont remote start says invalid key tried 2 tb boxs

vehicle will remote start with a fob in the car but with out it it comes up invalid key yes i install the tb box with fob chip as per instructions benn installing remote starts for 15 years not my firts install.
Login to reply View 2 answer(s)

12/07/2015

 Nissan Ara Her (770Pts.)

0

stand alone Nissan/Infiniti PTS no keyport

Hi, in order to activate lock and unlock from external output device , Do I need to connect the lock and unlock wires from the car or will be recognized from the evo all? Remote start works perfect on Stand alone , when I send negative pulse to the external input door look or unlock , the module blink blue but doors remains same . Remote start input works right, only lock and unlock not response. thanx
Login to reply View 1 answer(s)

11/07/2015

 Infiniti Ara Her (770Pts.)

1

Security light stays ON after start the vehicle

Hi there, Security light on infinit QX56 2013 stays ON after starting the vehicle and while driving. Installation mode: Standalone without Tharness. Remote start works perfect, the only issue is the security light stays ON when vehicle starts with remote start or without. after vehicle turn OFF, the security light blink like suppost to be. IVe tried to reset the ECU but still same. Any suggestion? Thanx
Login to reply View 2 answer(s)

11/07/2015

 Jeep AJBrown (320Pts.)

1

Optional Accessory Options - EVO-ALL CHRT5 (Jeep Wrangler)

Vehicle: 2015 Jeep Wrangler Alarm: No factory alarm, EVO-ALL configured for remost start with Alarm. Installation Type: Diagram C (https://fortin.ca/download/28831/evo-all_thar-chr5_(t-harness).rev-20150216.pdf) I have the EVO-ALL programmed and working using the instructions for diagram C at the above referenced guide. However, I want to add siren/horn, and dual stage proximity or shock sensor but there are no wiring diagrams to do this. Is it possible in the configuration I have? Is the parking light output (-) or (+) on my vehicle?
Login to reply View 1 answer(s)

06/07/2015

 Nissan Mike Evans (1960Pts.)

0

I can't get the RAP to shut down on my 2015 Nissan Rogue

I installed an EVO-ALL and tb-box along with a crimestopper rs2-g3 in a 2015 NIssan Rogue with standard key. The evo has the latest firmware 72.19. I can't get the RAP shutdown working. I have the light blue wire from the evo connected to the driver's door pin wire at the BCM. The wire never grounds after the remote start shuts down to trigger the door switch. The radio stays on. If the door is opened manually it shuts down as it should.
Login to reply View 1 answer(s)

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue