English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

08/11/2024

 Nissan mobilesolutionsar (280Pts.)

0

2016 Nissan Altima PCM humming sound and park lights staying on

Installed compustar alarm with remote start using a EVO-NIST4 and diagram75491, d2d cable being used. For some reason the PCM is humming and the park lights are on, what can be the issue? Do I change out the power wire fuse to a 1 amp since it comes with a 30 but I am not using those, just the D2D as the diagram says.
Connectez-vous pour répondre Voir 1 réponse(s)

30/04/2023

 Nissan Benjamin Duran (130Pts.)

0

Interior lights stay on

Altima 2008 coupe lights stay on, even if vehicle is off and locked. Once driving interior lights stay on as well. Evo nist1.
Connectez-vous pour répondre Voir 1 réponse(s)

20/01/2023

 Nissan XainK (130Pts.)

0

Brakes light up when remote starting but the 2010 Hybrid Altima does not start

This is a weird one, because the car remote starts pretty much every other remote start session. I'm not sure what's causing that as I checked the wiring and it doesnt seem like anything is wrong. So here it goes, when i try to remote start the car from far I see my brake lights turn on* (as in the brakes are being pressed) but the car does not start. the problem is mainly that the brake lights STAY ON unless I actually go to the car and start it myself, however even when i get to the car nothing pretty much works. I press the brakes myself and when I press the the push to start button it stays on lock (it goes LOCK-ACC-ON) so i pretty much freak out, unlock and lock mulitple times, press and depress the brake while keep hitting the push to start untill it goes off and then I manually start it. INFO: 2010 Hybrid Altima (Push to start) EVO-ALL using RL1 red connector in the module * passanger side brake light does not LIGHT UP, the bulb itself works only when i run the headlights but not when i press the brakes
Connectez-vous pour répondre Voir 0 réponse(s)

05/01/2022

 Nissan Mark Bauer (130Pts.)

0

2007 Nissan Altima red light flashing 3 times when trying to start

I have completed the install and programming everything seems to be done correctly. I did not connect the 3 wires to the bcm foot lock unlock and door pin because I don't want to. When I hit the lock button 3 times the unit clicks and attempts to start but then red light flashes 3 times and doesn't start.
Connectez-vous pour répondre Voir 3 réponse(s)

05/01/2022

 Nissan Mark Bauer (130Pts.)

0

2007 Nissan Altima red light flashing 3 times when trying to start

I have completed the install and programming everything seems to be done correctly. I did not connect the 3 wires to the bcm foot lock unlock and door pin because I don't want to. When I hit the lock button 3 times the unit clicks and attempts to start but then red light flashes 3 times and doesn't start.
Connectez-vous pour répondre Voir 3 réponse(s)

05/01/2022

 Nissan Mark Bauer (130Pts.)

0

2007 Nissan Altima red light flashing 3 times when trying to start

I have completed the install and programming everything seems to be done correctly. I did not connect the 3 wires to the bcm foot lock unlock and door pin because I don't want to. When I hit the lock button 3 times the unit clicks and attempts to start but then red light flashes 3 times and doesn't start.
Connectez-vous pour répondre Voir 3 réponse(s)

30/11/2021

 Nissan Armand Annereau (280Pts.)

0

installing Evo-All in 2008 Nissan Altima PTS Hybrid module not finishing programming

using installation guide #84521. get to last step in programming(# 8 flashing yellow) which I get once I turn off ignition (by pressing the PTS button once) i get a Red & Yellow alternating flash. which would mean Decryptor is ready right? steps do not mention decryptor at all. And I dont get the decryptor option in the Flashlink Software. Have confirmed Hybrid mode is on and even attempting rolling FW back for minimum required as listed in guide
Connectez-vous pour répondre Voir 1 réponse(s)

28/04/2021

 Nissan Gavin S (180Pts.)

0

Why doesn't 3X lock turn off my vehicle?

Nissan Altima 2008 PTS EVO-ALL-NIST1 001A06848886 Guide # 84551 Blue led blinks twice while off from fob lock/unlock command. Red led blinks and brake lights turn on after 3x lock, engine starts. Red and Yellow led remain on while in remote start. Blue led flashes twice from unlock, but not lock, command. A1-A6 enabled A7-A11 disabled (No support for OEM fob takeover before 2009) B1-B2 disabled C1 enabled D1 enabled (15 minute runtime) D2 disabled (this didn't help) D3 disabled (so vehicle will stay on) D4 disabled (not a hybrid) Protocol - Fortin No special functions No RF kit
Connectez-vous pour répondre Voir 1 réponse(s)

22/02/2021

 Nissan Jeremy Boven (480Pts.)

0

09 altima evo-all w/thar-nis1 tharness. Wanted to add siren and shock sensor need wiring diag.

Evo,all w/thar-nis1 t harness, oem remote, standalone. Green wires are for lock n unlock. Where is siren wire ?
Connectez-vous pour répondre Voir 1 réponse(s)

15/12/2020

 Nissan Roach Coach (150Pts.)

0

OEM Remote Control for Altima 2007/2008

Has anyone been able to figure out a workaround to have OEM Remote Control ("Lock Lock Lock") work for the Altima 2007/2008. I plan to use a cell phone starter, and my biggest reason for wanting a workaround is so that I can use the "keyless" entry method of unlocking the car once I actually walk up to the car. I want to avoid having to unlock the car soley thru the cell phone app, but instead press the button on the door handle to unlock the car and not have it shutdown. Is this possible?
Connectez-vous pour répondre Voir 1 réponse(s)

02/12/2020

 Nissan Wesley Bridges (140Pts.)

1

2015 Nissan Altima Ignition Ignition 2 wire

Not a question so much as an update to your notes. On the installation instructions it shows Ignition 2 as Pin 9 Black 24 Pin plug as a Pink wire. Vehicle I had it is not a Pink Wire it is Brown but when tested goes + when PTS is hit for ACC or IGN.
Connectez-vous pour répondre Voir 1 réponse(s)

01/01/2020

 Nissan Mohammad Kassab (130Pts.)

0

Remote Start for Nissan Altima 2008. Which product?

Hello, I am just interested in installing a remote start for my NIssan Altima 2008. After using the website to show me which products are compatible, it gives me the EVO-ALL or the EVO-ONE and I'm not sure which one to choose. Is choosing one of these products all I need? or is there something else I need? I am just interested in the remote start and nothing else. Also, I prefer to use the original key FOB to remotely start the car. Thanks,
Connectez-vous pour répondre Voir 0 réponse(s)

29/12/2019

 Nissan Josh Teague (190Pts.)

0

Got the evo rs evo-nist4. The diagram doesnt really explain what wires get cut and sliced were

I need help with the wires and what I'm adding them with.
Connectez-vous pour répondre Voir 1 réponse(s)

23/09/2019