Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

1

Evo All w/ Evo Start no RF kit programming

2018 Ford Edge, Standalone Evo All install, and adding Evo Start. Can not get the Evo Start to program or "mate" to the Evo all. I do have temp, GPS, and bluetooth telemetry to cell via Evo Start but can not get any functions to work via cell app. Programming, I have tried hold program button, plug in black data, release on RED AND BLUE, push till RED AND BLUE, release while constant RED AND BLUE, ignition ON...but do not get the quick flash of RED AND BLUE w/ YELLOW ignition led on. Can you please guide me to what my issue is PLEASE? Remote start via factory lock unlock lock works along with door lock/ unlock like it should. Located in the eastern states. THANK YOU IN ADVANCE ! ABSOLUTELY LOVE THE FORTIN BRAND AND PRODUCTS.

0

rfk442 program on a 2015 ford escape with evo one and t harness

what options need to be turned on in evo one to install a rfk442 long range antenna ,i can not get the blue light on antenna to flash properly am using a t harness on the 2015 ford escape

0

Trying to add compustar T13 RF kit and drone

I have 2012 Ford fusion, the evo all and compustar T13 RF kit and I can't get it to work

0

when the engine stops, the focus 2015 radio does not turn off

good afternoon. installed evo all. remote startup is working. I set it for 15 minutes, at the end the engine stops, the dashboard goes out, but the radio does not go out. help please

0

Why does my 2017 Ford C-Max Energi SE turn off seconds after successfully initiating a remote start?

I am currently utilizing the Evo One with my 2017 Ford C-Max Energi SE plug-in hybrid in conjunction with the T-Harness. I have checked wiring, factory reset and re-programmed the Evo one, and ensured the recomended bypass/remote starter settings are properly checked. If I had to guess, I would say that becasue my combustion engine does not start when the vehicle is started, until power is required, that the module considers it a false start and shuts down the vehicle. Any advice would be much appreicated. And since I'm here, when wiring the evo one into the horn, is the T-Harness(Orange/Black) wire spliced into the existing connection(Brown), or is the (Brown) horn wire being redirected through the module? The installation makes it clear that it appears that the connection is being redirected, but I wanted to be sure. Thank you!

05/12/2022

Ford Gene B (130Pts.)

0

Differentiate between fob and door keypad on ford / lincoln

Is there an option I can activate to tell my Evo All to ignore the input from the door keypad? I would like the fob to be the only option when remote starting the car. Should this not be possible, is there anyway the system can be changed from starting with Lock being pressed three times to starting with Unlock, followed by two lock combination.

0

flash limit reset EVO-ALL

my unit is showing that i need to update the firmware, but it states that i have reached my flash limit. Not sure how to get this done. plaese advise.

0

Parking light out put on fortin evo all

I'm looking at doing parking lights for my focus but i cant seem to find which wire is for the parking lights output for the fortin evo all. I can see on the diagram parking lights in but not out

0

Being able to add an rf kit and Parking Light t Harness

Im looking at adding a parking light t harness for my 2018 Ford Focus I found a parking t harness but the end of the Blue connetor that that plugs into the Evo- one is being currently occupied by my rf kit. Im wanting to add my rf kit and my Parking light t harness could i get a spliter that would be male to the Evo and split to two female ends allowing me to plug in the rf kit and the parking light harness. Finally in the end would i just need to get the evo all?

0

2014 fusion starts correctly, fan blows but will not engage heater controls for warm air?

Everything works correctly but the heater controls will not turn on and it only is blowing cold air from all exits. as soon as the key is inserted it turns on and hot air comes out of the designated vent.

0

FORD FUSION 2015 STARTS ONCE , AFTER THE FIRST START EVO ALL DONT START THE VEHICHLE

FORD FUSION 2015 EVO ALL STARTS ONCE , AFTER THE FIRST START EVO ALL DONT START THE VEHICHLE , it try to start but HORN ONLY AND NOTHING HAPPENS< PLEASE HELP

0

I can not get evo one to link with imoblizer on 2000 excursion

I purchased a flashlink programmer and still can not get this to work correctly. I also purchased a RF641 key fob set and still no luck. It cranks the ignition as it should but will not activate the imoblizer bypass. I have tried to program this at least 50 times using a stopwatch. I have also checked the wires and probed them no less than 20 times. I get a red light as normal then insert the first key for 3 seconds with solid red light and yellow turns on solid as soon as ignition is activated. Insert second key and yellow stays lit and a second into it the red starts flashing until the both go out. Can you please help?

0

F150 EVO ALL Strangeness

Hello, I am hooking up an EVO-ALL to operate my OEM remote starter via a CARLINK ASCL6. I am also attempting to add a shock sensor and blinking LED. I am using t-harness THAR-FORT4. It took quite a bit to get the ASCL6 to talk to the EVO-ALL. I could only get it to "talk" by sending a lock command during the learning process. For some reason I did it on a whim after trying all sorts of plug combinations etc. However, now it has no confirmation of the commands it sends. It send 3 separate pulses for the lock and unlock commands. I had to wire the Lock [(white/black) to BCM (blue/green)] and Unlock [(white) to BCM (yellow/violet)] for the lock commands to send. Why am I not getting a status reading? Do I have to wire the Driver Door Pin? I thought this would be mostly plug and play, but it seems like there is some wiring that needs to be done. Also, LED is wired to 12v+ and negative to white wire on the 20 pin but it is not working. I also have a shock sensor on the way and need help with that. I've been at this for 3-4 days off and on. Programmed as standalone remote start and EVO alarm via Flashlink. HELP! Thanks

09/10/2020