Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

25/11/2023

Ford Ben308 (130Pts.)

0

No crank on 06 Ford Focus (Evo One and RM442 Remotes)

Using the 1 key with Decryptor method, I programmed my evo one and paired the key fobs to the antenna, but when I try to remote start, it doesn't crank. It's sending power to the ignition and the anti-theft is not blinking so I think the bypass is working, just not sure why it doesn't crank. I should also add that the fob doesn't work to lock/unlock the doors, nor does it open the trunk. The antenna and module are clearly receiving commands but aren't able to do anything with them. I'm confused how this is supposed to work anyway, as the installation guide doesn't have me splicing lock signal wires to the module. Is it supposed to send the lock/unlock signal through the RX wire at the ignition cyclinder? I have a basic level of experience with electronics but I'm stumped here. Thanks in advance for your help.

29/06/2023

Ford smrick2 (190Pts.)

0

Why does it only honk now when I remote start

Installed evo all with my car telematics with 944 rf kit and has worked beautifully since 2019 with the occasional horn honking when I remote start but I had to remove module and wiring from dash for some audio upgrades now all it does is honk the horn when I try to remote start. Does not try to crank everything powers up as it should then nothing. Thats on first attempt 2nd attempt does even do that. I have since go in and tried to reprogram module as t

29/06/2023

Ford smrick2 (190Pts.)

0

Why does it only honk now when I remote start

Installed evo all with my car telematics with 944 rf kit and has worked beautifully since 2019 with the occasional horn honking when I remote start but I had to remove module and wiring from dash for some audio upgrades now all it does is honk the horn when I try to remote start. Does not try to crank everything powers up as it should then nothing. Thats on first attempt 2nd attempt does even do that. I have since go in and tried to reprogram module as t

0

What setting would be needed to enable using RF 442 kit with Evo all kit and a Fort1 T harness

what setting woule be needed to enable for using RF 442 kit with Evo all

0

Horn and RF Kit with Drone

I have installed a Evo-one with t-harness on a 2015 Transit Cargo van. There is no horn chirp with lock or with alarm going off. Do i need to hook up a wire to horn or do i need a siren? Also i have purchased a RF kit and Drone, is there a way to hook up both? Thank you

0

RF-Kit install DIY

If I install a RF-Kit with the DIY method, where do I connect the 2 remaining wire in the antenna wiring in pin #1 and 2? Thanks

0

RF-Kit install on FOR2 T-Harness

Is it possible to install a RF-Kit on a 2018 F150 with a EVO-ALL standalone and THAR-FOR2? If yes how can I do it? I saw some guides that show how to wire pwr and gnd but non for the 2 remaining wire. Thanks

0

T9 not programming though Ft-D100 with EVO-ALL

I have a EVO-ALL installed in a 2014 ford focus hatchback with a key start, and i'm trying to add a compustar T9 rf kit to it. I have installed the FT-D100 (switching the blue and white wire before pluging into the unit) to go between the two and flashed the correct firmware for the unit. When I replug the 4 pin connector and go into the programing mode the lights do not flash. I do get all lights on when in the programing mode but it does not seem to see the remotes.

0

Connecting RM411 RF Kit to EVO-ALL

About a year ago I installed the EVO-FORT1 with the EVO-ALL and was using the 3x Lock on OEM remote and that works just fine and still does. I recently bought the RM411 rf kit with the ANT-FMH-SW antenna and have been trying to get the remotes to start my 2011 Ford Escape. I used the flash link and manager to update the EVO-ALL for the correct settings to allow the RF kit to work with it. When I go to try and program the transmitter, following this guide https://cdn02.fortin.ca/download/69291/rm411-install-guide-69291.pdf, it doesn't seem to work. At step 5 all three LEDs are on as expected but when I hold down the transmitter button for 12 seconds and release it the yellow light never blinks so the remote transmitter never programs correctly. 

 

What I am struggling with is that at step 5 all three LEDs on the EVO-ALL are on and the LED on the antenna is flashing. So this would mean the the EVO-ALL is in programming mode and has communicated to the antenna correctly so it is looking to program the remotes. So I have the data-link connection made and the antenna has power. When I hold the transmitter button for 12 seconds and release it the LED on the antenna momentarilly stops flashing indicating that it is communicating with the remote just fine. So for some reason the antena seems to not be communicating back to the EVO-ALL, or the EVO-ALL isn't picking up the right information from the antenna. Any ideas how to work around this? Thanks.

 

For information, I have the H2 option turned on (Fortin2 for the RF Kit) and the 3x lock on the OEM remote still works so I know the EVO-ALL is communicating with the car.

0

2012 Ford Fusion using EVO RS - Fort 1 - Which RF Kits works with this unit.

Has anyone hooked and RF kit up to the EVO RS. Have a Ford Fusion 2012. Hoping to use a single button RF kit to reduce size of fob.

0

T9 not programming though Ft-D100 with EVO-ALL

I have a EVO-ALL installed in a 2014 ford focus hatchback with a key start, and i'm trying to add a compustar T9 rf kit to it. I have installed the FT-D100 (switching the blue and white wire before pluging into the unit) to go between the two and flashed the correct firmware for the unit. When I replug the 4 pin connector and go into the programing mode the lights do not flash. I do get all lights on when in the programing mode but it does not seem to see the remotes.

0

T9 not programming though Ft-D100 with EVO-ALL

I have a EVO-ALL installed in a 2014 ford focus hatchback with a key start, and i'm trying to add a compustar T9 rf kit to it. I have installed the FT-D100 (switching the blue and white wire before pluging into the unit) to go between the two and flashed the correct firmware for the unit. When I replug the 4 pin connector and go into the programing mode the lights do not flash. I do get all lights on when in the programing mode but it does not seem to see the remotes.

0

Evo all + xl202 + viper 2 way rf kit = car starts then shuts off (sometimes twice)

My car (2014 ford escape) starts with viper two way remote press, then turns off after 5 seconds. Sometimes it starts twice, each time shutting down after 5 seconds. Options A1-A11, C1, D1, D1.6, and H5 set to ON My research tells me I need to set the tach at the viper control center (antenna) however the LED doesn't blink. All componants are talking to one another, but the car won't stay on. Any help is much appreciated. Thanks!

20/08/2016