Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

24/09/2024

Ford Adrixe (180Pts.)

0

2017 ford escape starts when I turn ignition to RUN position and will shut down once I press the gear shift release.

Hi Guys,

need some help figuring out how to fix this problem.
My 2017 will start when I turn the ignition to run position. Then when I press the Shift gear release, the vehicle will turn off. Once I release the shift gear, the vehicle will turn on again.

I had the Fortin remote starter since 2019 and was working well. I added the rf kit and programmed fortin evo-all and was working.
I did some changes to the setting on the fortin evo all with the flashlink manager. after that, car won't start anymore with the remote start.
I reflashed the unit to see if it can work. but no dice. I was trying to do the 2 key programming but didnt work. turned the vehicle off.
Now the evo all wont go into program mode when attached to the vehicle and the car won't start. It wont even turn on when the unit is connected.

I removed the unit and that's when it will start when I turn the ignition to run. and shut off when I press the shift gear release. Then once I let go if the shift gear, it will start again.
It looks like its stuck into the remote stat system.
I removed all the t-harness wiring of the fortin and returned everything back to stock. But it's still doing the same.

I have removed the Negative battery that is attached to the frame and removed the positive terminal as well overnight. I haven't done anything yet today and will wait until I get back home to try and see if it would reset the ecu and go back to normal.

Question as well, can I short the Positive wire (Disconnected from the battery) and the Negative wire (Still connected to the battery) to reset the electronics or should I remove the negative battery terminal to do it? Its really hard to remove the negative terminal and easier to remove the one that is attached to the frame.
Or leaving the battery disconnected for 10+hrs is enough?

Thank you very much!

2

Evo All and RF Kit with Aftermarket Power Locks

Hey guys I got another quick question, I purchased the EVO All, THAR-FOR1 T-Harness and RFK442 RF Kit which I will be installing soon for remote start functionality. So my 2011 F-150 did not come with power locks so I wired up a relay with a momentary switch a few days ago which is working well so far (see link for wiring diagram below). https://www.caraudioforumz.com/attachments/car-alarm-mobile-security-85/14792-wiring-diagram-aftermarket-door-locks-trim.jpg My question was, would it be ok to hook up the lock pin A19 and unlock pin A5 on the EVO All (see Fortin wiring diagram below) to pin 85 and 86 which go to the momentary switch (see other wiring diagram). https://fortin.ca/download/94891/EVO-ALL_IG_RTS_BI_FOR-FSERIES-2011-2016_KEY80bits_D_94891.pdf My thought process here was that say for example, I click lock on the RF Kit which would send the command to the EVO All and then the EVO ALL would send voltage to the relay and finally the door will lock? Did I get this right? What's confusing me is why a diode is needed in that orientation, seems like it will be blocking the lock signal? Thank you so much!

2

Evo All and RF Kit with Aftermarket Power Locks

Hey guys I got another quick question, I purchased the EVO All, THAR-FOR1 T-Harness and RFK442 RF Kit which I will be installing soon for remote start functionality. So my 2011 F-150 did not come with power locks so I wired up a relay with a momentary switch a few days ago which is working well so far (see link for wiring diagram below). https://www.caraudioforumz.com/attachments/car-alarm-mobile-security-85/14792-wiring-diagram-aftermarket-door-locks-trim.jpg My question was, would it be ok to hook up the lock pin A19 and unlock pin A5 on the EVO All (see Fortin wiring diagram below) to pin 85 and 86 which go to the momentary switch (see other wiring diagram). https://fortin.ca/download/94891/EVO-ALL_IG_RTS_BI_FOR-FSERIES-2011-2016_KEY80bits_D_94891.pdf My thought process here was that say for example, I click lock on the RF Kit which would send the command to the EVO All and then the EVO ALL would send voltage to the relay and finally the door will lock? Did I get this right? What's confusing me is why a diode is needed in that orientation, seems like it will be blocking the lock signal? Thank you so much!

0

Trying to add compustar T13 RF kit and drone

I have 2012 Ford fusion, the evo all and compustar T13 RF kit and I can't get it to work

01/11/2022

Ford Moike (580Pts.)

0

rf 441 programming not responding?

2008 ford escape installed evo one (wire to wire) with 1 key, but when programming rf441 the antenna blue light is just on and does not respond when you step on the brake 4 times. I tried a different set of rfk441 but still the same result sn 002b04253021 Thanks, Mike

26/11/2021

Ford a a (190Pts.)

0

Rf remote program

Hello, i have a evo-all-442 installed into a 2009 f150, i have the evo all programmed fine lock lock lock works, when i go to program the fobs, the antenna does not flash and the fobs will not program, i was using the prgram instructions that came with the kit, is there any other way to program the fobs?

19/11/2021

Ford a a (190Pts.)

0

Evo one include an rf kit

Does an evo one for a 2009 f150 include an rf kit with a 2 way fob?

0

How to program Revo 4.1 to the Evo-One?

I have purchased the Revo 4.1 rf kit to go with the EVO-ONE. I went to program EVO-ONE with the Flash-Link 4 prior to receiving it. So I am ready to go when it arives. There is no option to select the Revo 4.1 rf kit. There is only the smartphone and Forin rf kit choices, or no rf kit. How do I select the Revo 4.1 rf kit ro program with the EVO-ONE?

0

Will the Crimestopper 2-way pager transmitter work with the Evo one?

I have several 1and 2 way remotes SPLCD52 from previous Crimestopper RS7-G5 remote start units. Will the 2-way 5 button remotes work with the EVO-ONE? If so is there any literature on programming? The antenna harness only has 3 pins. Where the EVO-one has a 4 pin antenna connection.

0

Horn and RF Kit with Drone

I have installed a Evo-one with t-harness on a 2015 Transit Cargo van. There is no horn chirp with lock or with alarm going off. Do i need to hook up a wire to horn or do i need a siren? Also i have purchased a RF kit and Drone, is there a way to hook up both? Thank you

0

How to program RM441 rf kit to Evo one

RM441 program to evo one

0

Evo-Fort1 with RFK942 only locks with RF remote on 2012 Ford Focus

When I hit lock button on the RFK942 remotes, the EVO-FORT1 locks fine. When I hit unlock on the RFK942 remotes, it will not unlock. OEM remotes both work fine and EVO-FORT1 starts with all remotes. Only issue is it will not unlock with the RFK942 remotes.

0

when uses 3x lock and rf 64-2w start button vehicle starts. But wont shut off using brake pedal

I installed evo fort-1 on escape 2008,standalone system,when pressing 3x lock,rf 64-2w starting button,vehicle starts.but vehicle wont shut off and also evo all module wont shut off when pressing the brake pedal,and using the rf 64-2w button vehicle wont shut off. i been installed this evo fort1 w/ rf kits on escape 2008 and 2010 before,i dont have any problem on pressing brake pedal, the vehicle will shut down and also on using rf remote vehicle will shut off.wondering if there is faulty on the evo all module or theres need to activate on the new module. this is the module number i installed on the vehicle. model evo all date 09/2019 sn 001a07071083 please give us advice thank you in advance.