Questions & Answers

Hello,

I recently bought Evo start 2 for my Evo one which I have been using for more than 2 years on my Mazda cx 3 2019 with T harness. At that time I did not choose the app start option while programming the Evo one. Can some please help me where should i be connecting the Yellow wire. Does it goes into the A1. Also none of the other options like door unlock are not working. Do I have to reprogram the Evo one again. I know that the firmware should be atleast 1.21. When i push start from the app the green light on the evo start 2 is turning on but nothing is happening.

I have followed the following steps and it was not working.

Ignition ON - OFF - ON (While holding the brake?)

Press and release brake 4 times

Press and hold the Evo start button until green

Turn OFF Ignition

Thank you for reading any kind of help or suggestions is much appreciated 

I am following steps in Guide #68261.

1) As per large yellow "ATTENTION" warning, disconnected - terminal from battery.

2) Removed covers

3) Made the following connections: #4,#5,#6

7) Made the other required connections: Diagram on page 4 (Connect everything else)

6) Reconnect - battery terminal

Page 7 Step 1: Connect the 6-pin Main Harness

--already connected everything to Evo-One control at #7, however diagram show Evo-One control with NOTHING connected !

Are those connectors magically disconnected by themselves ? Maybe  missing instructions ? 

....disconnect battery - terminal ?   .....disconnect all connections from Evo_One control ? ...reconnect - battery terminal ?

Hi All,

I tried following the instructions to a T (https://cdn02.fortin.ca/en/download/62681/62681.pdf). It seemed based on the instructions that I needed to remove the Red (Door data) and lt. blue (Door lock) wires from the data connector and splice them directly into the relative cables from the T-Harness.

These wires were free and not connected to anything on the other end, so I assumed this would need to be done. However, after doing this and trying to program my remote, it will not turn yellow and only remain blue. Can anyone figure out what I may have done wrong here? Now, I can't get into my car with my key fobs anymore.

After installing the EVO ONE with THAR-ONE-MAZ3 everything seemed to be working, but now(4 days later) whenever I start the engine with the remote starter I get the folowing warning "Front Radar Sensor System Malfunction" and the only way that I know how to make it dissapear is to turn off the engine and turn it back on from the push to start button. Is there any other solution to this problem? 

Hey everyone,

I just installed the Fortin Evo-One in my 2020 Mazda CX-5 and everything works fine except the Auto Hold feature, but only when the car is started remotely. I've made sure all doors are closed, my seatbelt fastened, car fully stopped in drive and I just get 3 flashes.

When started normally, it works just fine.

I've tried re-flashing the Evo-One module and tried running the DCryptor sequence again but same issue both times. Unit was installed with the THAR-ONE-MAZ3 T-Harness.

Has anyone else had this issue or have any troubleshooting advice?

I boutght The mazda EVO-All with T-harness for my 2015 Mazda PTA automatic and I am confused about the wiring on number 2,3 and 4 in red circles.

On guide #62681 page 6 at the bottom of the page(#2 in red circle) it says that I need to connect LT.BLUE/BLACK Wire to Pin#8 and the Lt.Blue wire to #9 pin on 32-pin White connector.my question is how am I supposed to do this?Do I need to disconnect the 32-pin White connector from Car and connect these 2 wires individually to the part which is attached to the car or the part wich I disconnect from the car?there is no conncetor in the harness to connect these 2 wires.

I have the same issue with #3 and #4 in RED circles at the bottom of the page 6 as-well.how am I supposed to conncet the D section on Evo-All to #1 & #3 on the 8-pin White connector and also connect 4A an 4B on the engine compartment.

I do not see any part on the harness to coonect these parts.am I supposed to buy connectores,strip the wires and attach the wires by myself?there is no extra connector or pin or wire stripper in the package.

Thanks for your help.