Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

23/10/2024

 Chevrolet Ctmodfan (180Pts.)

0

Flashing EVO One for use with 2016 Chevy Cruze Limited and there's no option to use OEM key fob.

I have an EVO One with a THAR-GM1 and was able to successfully program it (using the program button and key/ignition), after wiring it into my 2016 Chevy Cruze Limited Manual Transmission. However when I attempted to flash it using a Flashlink 4 and my laptop, I don't have an option to use the factory key fob. I double and triple checked the settings, but under OEM Key Fob and it only says that it's not available. Am I doing something wrong? Thanks in advance for your help.
Login to reply View 1 answer(s)

27/12/2021

 Chevrolet Bobby B (390Pts.)

0

Doors Relock Immediately after Pressing Remote Unlock

Hello. Installing Evo-All into a 2014 Chevy Cruze with regukar key. Now, when unlocking the car with the factory remote, the doors relock one second later. It's not consistent but is happening frequently. 3x factory remote start function works fine. I can only test this with the engine off because the factory remotes are disabled during remote start (I know this is normal). I have the alarm settings turned off (tried it both ways) and also turned off the smart relocking feature. Firmware is correct. Looking for any advice Model: Evo-All Date: 07/2021 SN: 001A07 273090 THAR-GM7 T-Harness RM-441 RF Kit Thanks, Bobby
Login to reply View 1 answer(s)

06/05/2020

 FAQ Cam Cross (1070Pts.)

0

Excalibur RF51EDP Paging Notification

I am adding a Excalibur RF-51-EDP to my EVO-ALL Alarm/ Remote Start. My question before purchasing this unit is will paging notifications work with my EVO ALL? The only reason I am getting this kit over a fortin RF kit is the ability to recieve notifications on the remote if someone tries to get into my car or sets the alarm off when it's nearby. I found on the Fortin RF kit page that it is compatibile, but it doesn't say if paging will work or not.
Login to reply View 1 answer(s)

13/12/2019

 Chevrolet HARPREET SINGH DHILLON (670Pts.)

0

If check engine light is on

If check engine light is on already.can I still install evo all standalone remote start in 2011 Cruze.
Login to reply View 1 answer(s)

13/05/2019

 Chevrolet Harald Luksch (180Pts.)

0

Fortin EVO-ALL does not start Chevrolet Cruze 2011

I have installed and programmed the EVO-ALL in a 2011 Chevrolet Cruze. When I try to Start the engine with "3 times lock" I can see the blue LED correspond to when I push the lock button. It starts the process, unlocks the doors, ignition AC and radio go on, but does not crank. The procedure starts again - same result. Wat am I doing wrong? I also made a master reset and went through the complete programming and flashing again. And yes, C1 and D1 are activated .... No more ideas. Thanks in advance, Harald
Login to reply View 1 answer(s)

31/01/2019

 Chevrolet Roger lambalot (130Pts.)

0

Compustar Prime G15 RF-1WG15-AM compatible with EVO All

Purchased the EVO-GM1 for my 2012 Chevrolet Cruze. Want to install it in standalone but need to purchase an RF Kit since my factory FOB want function after car is started. Looking at picking up the Compustar Prime G15 FR-1WG15-AM RF Kit. Can't anthing on the internet to figure out if this is compatible with the EVO-GM1. Thanks
Login to reply View 1 answer(s)

20/12/2018

 Chevrolet Wilber Cancio (130Pts.)

0

My Evo-All does not start my Cruze 2017

I have a Cruze 2017 standard Key and I bought an Evo-All, followed all the steps of the guide,  the blue light flash slowly, after decryption complete, I installed the Evo-All again in the car, without pressing the programming button, when I press the lock buttom  three times the car does not start, every time I press the lock buttom the blue light comes on, but not nothing happens. The same is when i press, lock-unlock-lock.

Login to reply View 2 answer(s)

25/12/2018

 Chevrolet Roger Blais (130Pts.)

0

2011 chevy cruze only remote starts part of the time.

i installed THAR-GM1V2 using guide # 63361 and RF-ALL 642W using guide #25431.The car will start just fine normally with the flip key. the new 2 way fob also works for unlock/lock/trunk but the remote start only works every now and then. usually it'll just turn on the dash lights but thats it. its tries that like 3 times and then just stops. but every once in a while it'll actually start. it will show the anti theft light on the dash though. its also started and stopped after a couple seconds. any ideas?
Login to reply View 1 answer(s)

21/12/2018

 Chevrolet tony leonardi (130Pts.)

0

2017 chevrolet cruze wont start

2017 chevrolet cruze with a t harness style kit programing and dycriptor process went by the book all went well but, wont start when i press the lock button three times blue light flashes each time i push but no start. please advise
Login to reply View 1 answer(s)

20/12/2018

 Chevrolet Wilber Cancio (130Pts.)

0

My Evo-All does not start my Cruze 2017

I have a Cruze 2017 standard Key and I bought an Evo-All, followed all the steps of the guide,  the blue light flash slowly, after decryption complete, I installed the Evo-All again in the car, without pressing the programming button, when I press the lock buttom  three times the car does not start, every time I press the lock buttom the blue light comes on, but not nothing happens. The same is when i press, lock-unlock-lock.

Login to reply View 2 answer(s)

27/08/2018

 Chevrolet David Davis2 (310Pts.)

0

2014 CHEVY CRUZE FLIP KEY - SEVICE THEFT DETERENT SYSTEM Manual Transmission

I am still having issues with my Evo All and Crimestopper modules. I am able to get the car into reservation mode by putting the car in nuetral and setting the ebrake. Once the car is in reservation mode I can pull out the factory key and get out of the car and lock the doors and the car shuts off. Everything is good up until I try to remote start the vehicle. The driver information system starts doing its checks but then stops and says "Service Theft Deterrent System". I have already performed a master reset on the evo all module with no luck. All I am looking for here is a list of things to try. One thing that I am confused about is the disarming of the alarm since the Crimestopper can unlock the car before the remote start and so can the evo all. I have also read in some questions that the immo wire needs to be cut but I am using the GMT T-harness for connections to the car.
Login to reply View 1 answer(s)

13/01/2018

 Chevrolet Logan McElhatten (130Pts.)

0

2014 Cruze decrypted successful plugged back in does nothing for 3x lock start evo rs gm1

2014 Cruze lt standard key everything wired correctly did decryption and it said successful plugged back in will not start in 3x remote start mode. Gm1 evo rs package. Tried calling support center on hold 2 hrs without talking to a Damn person. Never blinked blue slowly when I tried the plug connector at the end of bypass programming just stayed solid but I did do decryption. Connected everything up right but does not work
Login to reply View 1 answer(s)

22/12/2017

 Chevrolet Gene Chiu (130Pts.)

0

Buying EVO-GM1 for 2014 Chevy Cruze

Hi there,

 

I would like to buy Fortin  EVO-GMT1 this remote starter system, but I have some question I wish that you help me.

 

Do I need to buy flash-link updater or I just need to buy Fortin  EVO-GMT1 then after installing I can use directly?

 

I'd use the 3X lock button on the OEM remote.

 

My car is 2014 Chevy Cruze LS.

 

Thank you.

 

Gene

Login to reply View 1 answer(s)

31/10/2017

 Chevrolet Jason Anderson2 (130Pts.)

0

No lights on the EVO-ALL, no remote start working on 2014 chevy cruze

Hello, I have a 2014 Chevy Cruze I'm trying to set up in stand-alone configuration with an EVO-ALL. Service number is 003606 007301. Flip-key, not push-to-start. I have the flash-link-4 module, which seems to be working fine. Unit appears to be doing nothing at all. Initially, when I plug it in, all 3 LEDs flash simultaneously a few times, then nothing happens. To be clear, after the initial plug-in, no lights appear on the EVO-ALL at all, even when a button is pressed on the remote (I believe I read that I should see the blue light flash indicating data is being passed, is that correct?). Does this mean my CAN-connector is not connected properly? I am plugging in the 4-pin connector first, as per the instructions, then the rest of the wires. I don't care whether it's lock-lock-lock or lock-unlock-lock (as I currently have it programmed). I've tried both ways. What am I doing wrong?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue