Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

22/10/2024

 Chevrolet Ctmodfan (180Pts.)

0

EVO One with THAR-GM1 V2 in 2016 Chevy Cruze Limited Manual Transmission

Hello all, I am getting ready to install an EVO One Module as a remote starter only, with a THAR-GM1 V.2 Harness in my 2016 Chevy Cruze Limited, with Flip Key and manual transmission. The wiring diagram only shows the Pink wire from the High Power (6 Wire) Harness being used. Does that mean I don't have to hookup the other 5 High Power Wires, or are they required for the unit to function? I haven't been able to find any wiring schematic for where the wires (aside from power and ground) hook up in my car. I guess I am unlcear on whether or not the GM Harness renders those other 5 wires unnecessary. Thank you in advance.
Login to reply View 1 answer(s)

31/10/2019

 Chevrolet Tate Jeurink (180Pts.)

0

How do I Program standalone remote start on 2016 Impala?

I am doing an install on a 2016 Impala with standard key. Using the T-harness and EVO-ALL standalone remote start. When I get to step 5 and turn the ignition on the red and yellow LEDs flash. I have not been able to get past this step. I did already do as the troubleshooting guide said and plugged the red connector in and let the car run for a minute and then start over. This didn't get me any further.
Login to reply View 1 answer(s)

25/12/2018

 Chevrolet Roger Blais (130Pts.)

0

2011 chevy cruze only remote starts part of the time.

i installed THAR-GM1V2 using guide # 63361 and RF-ALL 642W using guide #25431.The car will start just fine normally with the flip key. the new 2 way fob also works for unlock/lock/trunk but the remote start only works every now and then. usually it'll just turn on the dash lights but thats it. its tries that like 3 times and then just stops. but every once in a while it'll actually start. it will show the anti theft light on the dash though. its also started and stopped after a couple seconds. any ideas?
Login to reply View 1 answer(s)

29/11/2018

 Chevrolet Brandon Sanderson (160Pts.)

0

Need to Reprogram to add new key?

I currently only have one key for me 2016 Cruze. I eventually plan on getting a secondary key, will I need to reprogram the unit once I get my new key for both to work?
Login to reply View 1 answer(s)

16/03/2015

 Buick Hui Zhou (130Pts.)

0

Regal 2010 on EVO ALL with THAR-GM1V2 programming fail

My car is Regal 2010 flip key with auto transmission I got EVO-All and THAR-GM1V2, everything is well installed. Firmware is upgraded to latest version of this car. When I follow the programming guide step4, that is a long step, some actions requires to be finished within 5 second. When I finish step4 within 5 seconds, the yellow light keeps on and red light flash rapidly, which is differenct as guide shows. Please help. What should I do? Add more info I want to use it with oem remoter. The issue I described above was follow the programming guide. And it was not success as I mentioned. Then I tried to follow the decryptor guide. It's also difference as the guide shows. In the guide the last status should be blue light flash rapidly then remove the key blue light flash slowly. In my case the blue light keep light on before and after remove the key. However I still finish the whole process with flash link updater. When I reconnect the 4-Pin connector back after all the remaining connector, both red, yellow and blue light keep flash. I don't know whether the status is correct or not. When I push unlock button 3 times, nothing happen. Any more info needs, please let me know.
Login to reply View 1 answer(s)

01/02/2015

 Chevrolet Brett Smith (250Pts.)

0

Key fob doesn't work while car is remote started

2011 Camaro SS When the car is under remote start, the key fob doesn't work. I cannot lock or unlock my doors during this period using the key fob. I assume this is because the car is running but that doesn't do me any good. GM V2 harness that is for this application
Login to reply View 1 answer(s)

23/01/2015

 Chevrolet Hank Rath (310Pts.)

0

EVO-ALL - Bypass function not working on 2012 Camaro

Hi I am installing an EasyGo Push-2-Start system on my 2012 Camaro with the THAR-GM1v2 harness. While all the connections seem to be working fine, neither push-button nor remote start work, but trigger the immobilizer system. The EVO-ALL programmed fine, I tried the standard procedure as well as the decryptor one, had the data send to you servers and the result loaded to the module as supposed to be. If trying to trigger the start manually using the dark blue (GWR-) wire and the purple-yellow (Starter) wire, nothig happens either. Please advise.
Login to reply View 1 answer(s)

28/01/2015

 Chrysler Chris H (260Pts.)

1

What is the amperage ouput of the parking light output on a EVO-ALL?

I have the EVO-ALL, hardware version 6. What is the amperage output of the parking light output? I understand this is a negative ouput, which the car does need for parking lights. I am just making sure not burn out the EVO-ALL. Does it have a built in relay for this or does it need to be hooked to a relay in order to handle any current?
Login to reply View 1 answer(s)

18/01/2015

 Buick brian streu (130Pts.)

0

The evo all light is solid yellow when key is turned on is this ok

Also the lc-7 will not flash to program remote i am using the thr gm1 v2 harness do i need to power the lc-7 seperatly
Login to reply View 1 answer(s)

07/05/2014

 Chevrolet (Pts.)

0

Thar-GM1 v2 2014 chevy cruze doors will not unlock once car starts.

I have installed everything and got the car starter to work, but now I can not get the doors to unlock once the car is started, unless I unlock with the key. Is there a fix for this? Also is there a way to turn the auto start off without getting into the car? Does it shut off automatically after a period of time? I used the stand alone installation.
Login to reply View 1 answer(s)

13/03/2014

 Chevrolet Gabriel Harant (140Pts.)

1

Installed the THAR-GM1v2. Why wont my 2014 chevy cruze start with remote

Service#001A06 294619. I have a 2014 Chevy Cruze. I bought the EVO-All with the Harness. Installed as Stand Alone. think programming went well. Car will not start. I only wired up the brown wire to OBD connector. Am I missing something?
Login to reply View 1 answer(s)

11/01/2014

 Chevrolet (Pts.)

1

What is the modification to modify EVO-GM1 to EVO-GMv2?

What is the modification required
Login to reply View 2 answer(s)

11/01/2014

 Chevrolet (Pts.)

1

What is the modification to modify EVO-GM1 to EVO-GMv2?

What is the modification required
Login to reply View 2 answer(s)

25/12/2013