Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

2015 Corolla, flashes 4 red flashes & 3 red flashes

I have a 2015 Corolla with an automatic transmission start button. 

Installed with THAR-TOY6 T-Harness & EVO ALL

The device flashes blue when opening or closing the doors, but when trying to operate it with the remote, it flashes 4 red, I keep trying to program it and it gives me 3 red flashes.

SN:001A07261560

Flash blue once before red flashes

Please see the attached video.

https://photos.app.goo.gl/6rfod5uAwRBQ7MgUA

0

RF741W remote has solid red light when batteries are in & antenna is flashing blue

I’ve had my vw for 4 years now, when I bought it the remote starter was already installed . I’ve never had a problem up until recently this winter, my remote batteries seemed like they were dying quicker than ever. And after the last time I replaced the batteries the red led on the remote comes on and doesn’t allow any function to be done. The remote starter is useless right now if i can’t start it

0

INT-SL+ not programming on 05 sequoia.

Int-sl+ not responding when hit the lock button. Red light just stays on.. no flashing, no nothing. Any idea? It's flashed to firmware 0.17

13/01/2024

Audi Dsk (140Pts.)

1

EVO ALL - 2012 Audi A4 Step 7 flashes red 3 times

I am in the process of installing this and I get to step 7 and it is supposed to be solid red then in step 8 red and yellow alternating. At step 7 after Blue red yellow alternate it goes to 3 red flashes over and over. What could be causing this?

0

Solid Red Light even after using dcryptor/adapter

After installing, as per instructions provided, there was only a solid red light on my module. I notified tech support, and the person sent an dcryptor adapter. I followed the instructions in that video as well, but the program states: "the module was not able to sample the vehicles immobilizer data. Reconnect the module to the vehicle and follow the programming instructions from STEP 1 to sample the immobilizer data." Now I feel stuck, because it seems as though the module doesn't connect to my car. Please advise.

0

Red light is blinking after installation and using Dcryptor , what does that mean?

I connected all the wires, set up the dcryptor but remote start is not working and when I click on lock 3x red flashing light turns on, what might be the issue since everything is connected and remote is encrypted

0

Civic 16' (Manual) w/FTX64 2W - Ready mode no longer saving my dashboard preferences

Hi, I Have a Honda Civic 2016 (Manual). I bought an aftermarket remote starter in 2019. The controller is an FTX64 2W. I used it without issues up until this winter. I would stop the car, leav it in neutral put the park brake on, and then press the ON button on the controller to start the Ready Mode. With the exception of the rear-window defroster which never worked, any preferences that I had on my dashboard would turn on when I activated the remote start later on (seat heaters, front window defroster, temperature, etc). This winter I noticed that when I get out of the car after activating my ready mode (after about 3-5s) the remote emits a red light and makes the descending noise (same on as if I remote stopped the car). When I then remote start the car, it will turn on, but none of the preferences on my dashboard will be on (cold seats, no defroster, no temperature, etc). The only thing that has changed is that one of the remotes (I have two) is dead. I will be replacing the batteries this week and trying that one out too. Anyone know what could be causing this? As I said, it worked well up until this winter and then stopped out of nowhere.

0

EVO All works a few times then won't start and red led flashes 5 times

2009 Toyota Venza Push-to-start. Installed EVO All and worked gopod for a couple days and then when customer tried to used the remote start, the parking lights blinked and the red led flashed 5 times but car did not start. SKU #: B-3475-455

0

INT-SL+ won't program to 2000 Silverado or be discovered by Flashlink Manager

I have a Fortin INT-SL+. HW Ver 2 Firmware Ver 3.01 mfg date 04/2018 Service number 002102061867 I also purchased a Fortin flashlink-lite updater I have a 2000 Chevy Silverado with an older Chrime Stoppers remote start, and had on omega IB-GMBP.DB-PAS-23A Passkey override. The omega unit went bad and appears to be discontinued. I purchaesd the Fortin unit to replace it. I just need the passkey function of the Fortin. Wired it in configuration 5 without data link. When I follow the programming instructions, the red light will come on, but not start blinking when the key is switched on. I have checked my wiring. I'm pretty sure I have it right. The red light also does not go out after I start the engine. I read on this forum that GM trucks can be particularly hard to program and that there is a firmware version 3.06 that resolves the issue. I bought the Fortin flashlink-lite updater to upgrade my firmware from 3.01 to 3.06 The flashlink-lite updater seems to be working with my laptop correctly. The Flashlink manager 4 shows the flashlink-lite updater as connected. When I plug in my INT-SL+ the red light comes on for a few seconds and goes out. Flashlink Manager4 always shows the "module status" as disconnected. I tried holding the INT-SL programming button before plugging the INT-SL into the Flashlink-lite. The red light stays on but the "module status" doesn't change. I have seen youtube videos that show the Fortin modules connecting almost instantly when plugged into the Flashlink devices, so I think something is wrong. I suspect the INT-SL I don't want to buy more stuff until I'm sure that I'm going to solve the problem. I feel that I should troubleshoot the connection between INT-SL+ and Flashlink first, since those are Fortin factory connections. That eleminates my wiring as a potential issue in the flowchart. Is there a way to tell if the INT-SL+ is bad?

0

Evo-ALL - try reset but getting 3 solid LED lights

Hello, I was getting the solid red light on my Evo-all. I decided to do a reset. I installed firmware 0.99 and while pressing programming button and connecting datalink from the car Instead of getting the solid red light I got all three solid lights. Can anyone tell me what does it mean and how do I get it to work ? I'm trying to install remote start to 2020 Rav4 XLE premium with push start.

0

Flashing red near programming button and module not responding to remote

Remote doesnt work after change car battery. Tried reprograming but not helping. Noticed red light blinking near programming button not the red with the other yellow and blue led. What could be wrong?

0

EVO-ALL won't code after cluster removed

Hello.

I have an Audi A3 2016 PTS that has an EVO-ALL V7 installed through a THAR-VW1 harness and it all woked seamless for months, with very minor glitces.

In while AC maitenance; namely the front door air actuator, I had to remove the imstruments cluster to have more room to work. It was a major pain, but I got it done.

Then I decided to check for a newer suggested firmware of my EVO-ALL and found v64.09, from v64.05 I was currently using.

The Cluster removal happened early in my project and only about 7 hours later the car was all reassembebled with some with some expected DTCs present, that were easily cleared to 0 DTC. When installed, the cluster was 100% operaciotnal, as everything else in the car - I only had to ajust it's clock .

But EVO-ALL was dead.

I came to the conclusion that the unit was not programmed any more in the car, so Idecided to try re-programming it all over again, but it keeps on failling on step 13: The LEDs keep flashing in 5x groups.

Installation manual used  with RLINK: https://cdn02.fortin.ca/download/82471/evo-all_ig_reg_bi_aud-a3-s3_2015-2016_pts_tb_a_82471.pdf
q

And this troubleeshooting guide says this is Cluster Protection Mode.

https://fortin.ca/en/vehicles/audi/a3/2016-push-to-start/troubleshooting.html

I don't see any issues or error message in he cluster, or in the infotaiment system.

I already left the car with the battery ON for 20+ minutes, but the issue persists.

I tried flashing back the version I had before, and also a master reset, but the 5x RED is always the final result.

How can I fix this situation??

 

Can I get a hand please?

0

Hi there! how to re-program or re-start the installation for evo rs all. red lit stay on

how to re-program or re-install evo all red lit stay on truck not start

0

Red LED not coming on with lock,lock,lock

Hello i have a 2012 Jeep liberty with EVO RS EVO-CHRT5. Flashlink updater also. Current software installed 74.{39} The rapid flash for programming occurred as the instuctions stated. Option C1 and D1 D1.6 and D1.10 are chosen. When trying the LOCK,LOCK,LOCK the blue LED occurs in sequnce with the lock button but nothing happens thank you in advance .

0

Solid red light after downgrading firmware.

0

Does the Red led always need to come on 2020 Silverado 1500, Evo-one?

Hello, thanks for looking at my question. I am using an Evo one, with A GM 7 T harness in a 2020 Chevy Silverado 1500 Everything has gone pretty well I installed the T harness, attached both unlock leads to the gray BCM plug, and the tailgate/trunk lead to the pink BCM plug, double checked pins, and that looks good. The Evo1 lights up like it is supposed to, except after the step where I hit the program button 5 times under the yellow LED and turn to run, the RED Solid never comes on the first try. After failing 3 times, I expiremented and turned the key a few tries until it eventually turned red. The steps resumed as expected I got the rapid flashing blue lights at on postion, went inside to windows computer and used the Dcrypter to record the key. that went well, no errors or issues with the fortin software. The problem is that the remote start does not work. Tried both the lockx3 and the lock+tailgate and it does not work to start car. Since the key flashed properly, and the LEDs resumed normally, is that red led lighting after the original 5 program button taps the issue, or are the 7 loose wires needing to be connected to something two greens, one blue, black, orange, orange and black wire. I followed the wiring diagram, these 7 loose wires I find unnerving, was it inferred what to do with these wires as a profession because I am DIY and might need just a little more of an explanation.

1

red flashing instead of red and yellow flashing?

Mazda cx-5 2018   Evo all guide # 66311   on step 13 I have an only red light flashing once every second and did not stop!!   I tried and read different solution founded here, but it ends with the same red flashing   all wires connected correctly 

0

EVO-ALL won’t switch from yellow light to red light after I start engine during programming.

2018 GMC Terrain using EVO-ALL and thar-gm6, yellow light turns solid but won’t switch to red while programming, tried reset and re flashing but still won’t work, light blue is connected to light blue/black.

0

Red flashes 6 times but does not crake

Trying to install on a 2010 Ford Escape, I have an Evo All with THAR-FOR1 harness. I get through step 3 and start doing the first key and the red and yellow light blink then stay solid after the 3 seconds. I then do the second key but only the red light comes on as solid. I pushed the programming button and the red light flashes 6 times, the ignition process begins but doesnt crank or have blue lights flashing. The anti theft light keeps flashing on the dash. I tryed to take it out of valet mode like I read in another QA, but that didnt do anything. I tryed to reflash the moduel and change settings. I rechecked all of the wireing. The SN is 001A07041799

0

Cranked but doesn't start; solid red & yellow light (after it cranked)

Hello, I've installed Evo-One on Toyota Camry 2014 G Key. After successful programming (installation), when I use OEM 3x lock to start the car, it cranked but failed to star; the unit shows solid RED and Yello clor. Any hi9nt pleasee? Thanks, Qamar

0

Red Light flashes 6 times and won't start

07 Durango, Evo All standalone with T-Harness, was working perfectly fine using 3x lock on OEM remote, or using a compustar remote that came programmed when I bought the vehicle. Blue light activates when locking or unlocking, orange light activates when ignition is turned on, battery hasn't been disconnected at all, power is fine, ground is fine, resistor from brown/white to parking lamps is fine, new battery in remotes, tested the hoodpin, I've pulled it entirely apart and checked all of the connections, and yet it blinks the red light 6 times, as well as the parking lamps and headlights, which I find extremely odd considering the troubleshooting only goes 1-5 flashes. Spent 2 days trying to sort it out and I've come up with nothing, any help or guidance would be appreciated.

0

My Evo One has yellow and red light on. What does this mean? I can't finish programming because of this.

I am following guide # 80961 for manual transmission. On page seven step step 5, the yellow light turns on but the red light never turns off. They both stay on even when I turn the key back to the off position. I have checked all connections twice and can't seem to figure this one out. Also, do I need a seperate harness so that my OEM remote works to control the EVO one?

0

Remote start works solid red light on evo-all illuminated 2009 RX350. Does not switch over to yellow or blue

Everything is connected. This is not my first time using evo-all. 2009 rx 350. Remote start cranks vehicle, red light on evo all illuminates, but will not turn on. Red light never changes over to yellow or blue light status. Car originally had an older remote start system with bypass. A New key was programmed. Car would crank with remote start, but would never run. Would repeat 3 times before shutting down. So, installed updated remote start system along with evo-all, same thing. Cranks will not run. Updated evo with latest software, still same issue. Did the key that got programed, effect the system?

0

two blinks from red LED after step 11 Guide # 82421

I am using the following on a 2017 VW Golf Alltrack PTS w/automatic trans: EVO-VWT1 kit with harness, VW-TB, EVO-ALL, RF-Kit 411 and R-Link. when setting up the unit in fortin flashlink I get no other options for installatiom method than "key in a box" and when attempting to program the unit with the R-Link installed I get all the way to step 11 and then the the flashing blue light turns red, then starts blinking two red flashes, pauses, two flashes and so on. I cannot get anything to work to get past this.

0

two blinks from red LED after step 11 Guide # 82421

I am using the following on a 2017 VW Golf Alltrack PTS w/automatic trans: EVO-VWT1 kit with harness, VW-TB, EVO-ALL, RF-Kit 411 and R-Link. when setting up the unit in fortin flashlink I get no other options for installatiom method than "key in a box" and when attempting to program the unit with the R-Link installed I get all the way to step 11 and then the the flashing blue light turns red, then starts blinking two red flashes, pauses, two flashes and so on. I cannot get anything to work to get past this.

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer