English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

20/03/2024

 Volkswagen jessica keresturi (130Pts.)

0

RF741W remote has solid red light when batteries are in & antenna is flashing blue

I’ve had my vw for 4 years now, when I bought it the remote starter was already installed . I’ve never had a problem up until recently this winter, my remote batteries seemed like they were dying quicker than ever. And after the last time I replaced the batteries the red led on the remote comes on and doesn’t allow any function to be done. The remote starter is useless right now if i can’t start it
Connectez-vous pour répondre Voir 1 réponse(s)

13/10/2020

 Volkswagen Jefferson Mosman (180Pts.)

0

two blinks from red LED after step 11 Guide # 82421

I am using the following on a 2017 VW Golf Alltrack PTS w/automatic trans: EVO-VWT1 kit with harness, VW-TB, EVO-ALL, RF-Kit 411 and R-Link. when setting up the unit in fortin flashlink I get no other options for installatiom method than "key in a box" and when attempting to program the unit with the R-Link installed I get all the way to step 11 and then the the flashing blue light turns red, then starts blinking two red flashes, pauses, two flashes and so on. I cannot get anything to work to get past this.
Connectez-vous pour répondre Voir 2 réponse(s)

13/10/2020

 Volkswagen Jefferson Mosman (180Pts.)

0

two blinks from red LED after step 11 Guide # 82421

I am using the following on a 2017 VW Golf Alltrack PTS w/automatic trans: EVO-VWT1 kit with harness, VW-TB, EVO-ALL, RF-Kit 411 and R-Link. when setting up the unit in fortin flashlink I get no other options for installatiom method than "key in a box" and when attempting to program the unit with the R-Link installed I get all the way to step 11 and then the the flashing blue light turns red, then starts blinking two red flashes, pauses, two flashes and so on. I cannot get anything to work to get past this.
Connectez-vous pour répondre Voir 2 réponse(s)

03/02/2020

 Volkswagen James Jean (130Pts.)

0

Why am I getting 3 red LED blinks after step 7?

UPDATE: I plugged everything in and gave it a try. Car starts right up but dies immediately. Gives me the "no key" alert. dcryptor process will not complete for some reason. 2013 Passat standard key, standalone install. EVO-ALL (2/2019), THAR-VW2, and TB-VW (1/2017). Guide 62471 SN: 001A07 008702 Flashlink Firmware: 75.39 TB-VW wired into brown transponder wire. I have all of the harness installed as directed but when I start the dcryptor programming, all goes beautifullt until the end of step 6. When I release the programming button, I don't get the rapid 3-LED alternation. The red LED just continuously blinks 3 times. I've even tried resetting the
Connectez-vous pour répondre Voir 1 réponse(s)

09/03/2019

 Volkswagen Cory Mah (130Pts.)

0

EVO-ALL will not continue programming after solid red light

EVO-ALL, THAR-VW1 Harness, TB-VW Standalone installation with Key Bypass, Automatic, PTS . FIrmware 75.38, Hardware v6 Guide #62501 During programming Blue light flashes rapidly indicating CAN bus activity when ignition is turned on. Press and hold programming button, Blue LED turns off and Red LED turns on Solid. After 3 seconds release programming button, and red LED begins to flash 3x and then repeats continuously. Nothing happens, the LED’s do not rapidly alternate, even after waiting 20 mins or more. Step 7 never completes, unit does not program. Wiring has been checked and rechecked. Any ideas why it doesn’t want to program?
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer